My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - American Response Vehicles
sbend
>
Public
>
Public Works
>
Board of Works Documents
>
2020
>
Opening of Bids
>
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - American Response Vehicles
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
4/9/2025 1:40:53 PM
Creation date
11/12/2020 11:10:06 AM
Metadata
Fields
Template:
Board of Public Works
Document Type
Contracts
Document Date
11/10/2020
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
340
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
Show annotations
View images
View plain text
that penetrate the body. <br />3. On screws and screw holes for any accessory whose holes are drilled and tapped <br />are drilled and tapped. <br />4. On the body surface when any accessory without a rubber or composite gasket is <br />to be mounted (i.e. entry or compartment door hinges or light assemblies without <br />gaskets) or composite gasket is to be mounted, i.e. entry or compartment door <br />hinges or light assemblies without gaskets. <br />ECK shall not be applied in the following conditions: <br />1. When mounting any accessory that has a rubber or composite gasket. <br />2. On light assemblies, which have plastic inserts for mount screws. Y N <br />25.1 PAINT <br />To produce a high -quality paint finish and to comply with the paint manufacturer's <br />certification requirements for support of the warranty, the preparation and painting <br />process described below must be used. <br />Prior to initiating the surface preparation process, all hardware, handles, light <br />fixtures, door hinges, corner trim, etc. shall be removed from the body. Additionally, <br />any portion of the chassis, which does not require refinishing, shall be protected from <br />the ensuing process. <br />To rid the aluminum body of any extraneous materials or material impurities the <br />entire surface shall be washed and wiped dry with a certified wax and grease <br />remover. Excess weld material shall be removed by grinding all welds, seams, and <br />any other body imperfections. The entire surface shall then be sanded with 80 - 150 <br />grit dry sandpaper to provide good adhesion for any fillers and primers. The required <br />areas will be filled with approved premium lightweight filler and sanded smooth. A <br />premium polysurfacer will be applied directly over these areas to ensure adequate <br />base for application of primers. <br />The entire surface shall be cleaned again with certified wax and grease remover <br />before application of any primers. A self -etching primer shall be applied to provide a <br />base for adequate adherence of materials to be applied in subsequent steps of this <br />process. A high -quality urethane primer surfacer shall then be applied. The entire <br />surface to receive topcoat will be sanded smooth to ensure a level and defect free <br />surface. <br />Door edges and doorjambs shall be prepared similarly to other body surfaces and <br />finish painted with a certified topcoat paint. The entire surface of vehicle body shall <br />be DA finish sanded with no coarser than 320 grit dry sandpaper. The surface shall <br />be washed and wiped once again with certified wax and grease remover and tacked <br />for application of urethane sealer. <br />A full wet coat of urethane primer sealer shall be applied and allowed to flash per <br />specifications. Basecoat color will be applied to ensure color correctness then clear <br />coated with a minimum of 2 full wet coats of qualified urethane clearcoat and baked <br />at 140 degrees for 30 minutes. <br />Surfaces to receive striping and graphics shall then be sanded with 800 grit dry <br />sandpaper and masked off for application of additional color(s). Basecoat color shall <br />be applied to stripe and graphic areas until color is correct. Entire sanded surface <br />
The URL can be used to link to this page
Your browser does not support the video tag.