My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - American Response Vehicles
sbend
>
Public
>
Public Works
>
Board of Works Documents
>
2020
>
Opening of Bids
>
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - American Response Vehicles
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
4/9/2025 1:40:53 PM
Creation date
11/12/2020 11:10:06 AM
Metadata
Fields
Template:
Board of Public Works
Document Type
Contracts
Document Date
11/10/2020
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
340
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
Show annotations
View images
View plain text
American Response Vehicles <br />POWER SOURCE: The aforementioned power provision will be wired through a relay and controlled by the <br />vehicle's ignition switch. Power for the aforementioned device or power supply will not pass through the <br />ignition switch itself. <br />LOCATION: The power source will be located behind the Action area control panel in the patient cabin. <br />POWER SOURCE FOR COMMUNICATION RADIO(S) No 4: Positive and Negative polarity ten gauge wires will be <br />supplied and installed for subsequent installation of communications radio(s). The wires will be barreled off <br />and protected by a thirty (30) ampere automatic reset circuitbreaker. <br />POWER SOURCE: The aforementioned power provision will be wired directly to the main vehicle batteries. <br />LOCATION: The power source will be located behind the Action area control panel in the patient cabin. <br />POWER SOURCE FOR COMMUNICATION RADIO(S) No 5: Positive and Negative polarity ten gauge wires will be <br />supplied and installed for subsequent installation of communications radio(s). The wires will be barreled off <br />and protected by a thirty (30) ampere automatic reset circuit breaker. <br />POWER SOURCE: The aforementioned power provision will be wired through a relay and controlled by the <br />vehicle's ignition switch. Power for the aforementioned device or power supply will not pass through the <br />ignition switch itself. <br />LOCATION: The aforementioned power source will be located in the cabinet "P" on the upper curbside wall <br />forward of the squad bench and curbside upper cabinets. <br />POWER SOURCE FOR COMMUNICATION RADIO(S) No 6: Positive and Negative polarity ten gauge wires will be <br />supplied and installed for subsequent installation of communications radio(s). The wires will be barreled off <br />and protected by a thirty (30) ampere automatic reset circuit breaker. <br />POWER SOURCE: The aforementioned power provision will be wired directly to the main vehicle batteries. <br />LOCATION: The aforementioned power source will be located in the cabinet "P" on the upper curbside wall <br />forward of the squad bench and curbside upper cabinets. <br />ANTENNA LEADS <br />ANTENNA BASE: The antenna base will be a series K-94 with an integrated cable. The origination point will be <br />lined up with the edge of the curbside entry door, centered side to side as near as possible. The coaxial cable <br />will terminate inside the add on console. <br />ANTENNA BASE: The antenna base will be a series K-94 with an integrated cable. The origination point is <br />located approximately 24 inches back rearward of roof port #1. This coaxial cable will terminate behind the <br />main action area board. <br />M <br />
The URL can be used to link to this page
Your browser does not support the video tag.