Encroachment and Revocable Permit - 1425 E. LaSalle Ave

Home Browse Search

i S fl ?`i ,I � 4. The %z`-wlde rabbet is cut%" deep into It/e" face of the trim material. 5. The rear -comer side p Intts fit otst llte tildes el rho roartttmer «ar piecn.0. The roof deck panels meet at the roof peak and overhang the box sides equally, 7. Fasten the roofing boards so the lower nails go through the roofing board below. bottom edge of the panel. Drill a 3/x-inch startei hole (see Making Curves and Interior Cutouts on page 32) on the inside of each corner of the rectangle, Then make the cutout with a jigsaw (photo 2). Assemble the Box Apply wood glue to both side edges and the rear edge of the plywood base and to the rear -side edge of each side panel. Assemble the base, sides, and back so the base fits inside the assembly and the back panel firs over The edges of the side panels. Clamp The parrs together. Fasten the pieces wirh Three FIX -inch screws along each joint. Glue the front edges of the base and side panels. Fit the front panel over the sides and base so all pieces are flush on the outside and the bottom. Fasten through the front panel and into the sides and base with three 1-inch screws along each edge (photo 3). Prepare the Front -Corner Trim The two front -corner trim pieces are first rip -cut from 2 x 3 lumber. Then They each get a 1'z z %a-incli rabbet cut along one long edge, creating a lip that overlaps the corner of the plywood box (see Making Doors with [or without] Rabbets on page 34 for help with cutting rabbets). T}tcy are also mitered on their rop ends at 36 degrees, Its easiest to make the long rip curs and rabbet on a single piece of 2 x 3, then cut the trim to final size with a miter saw or miter box. Cut a 6-foot 2 x 3 roughly in half and set one of the halves aside; you will use it later for the roof cap, Use a straightedge guide to rip -cut the 2 x 3 to 17A inches wide x IIA inches thick. Then, cut a'/z-inch-wide x N-inch- deep rabbet using a router and'/_ -inch rabbeting hit or a circular saw and straightedge guide (photo 4). Cut each trim piece to length, mirering The top end at 36 degrees. Install the Front -Corner Trim Apply glue to both sides of the rabbet on each piece of front -corner trim. Position the trim at the front corner of the box assembly so he top (mitered) end of the trim is flush with the angled Top edge of the side panel and the lip is up against the side panel. Drill '/te-inch pilot holes, and fasten each trim piece with three 2Y_-inch finish nails driven through the front of the trim and into the edges of the side panels. Set the nails with a nail set. Install the Remaining Box Trim Cut the rear -corner trim side and rear pieces to length, mitering their top ends at 36 degrees, The side pieces are mitered across rlieir IAA -inch faces. The rear pieces are mitered across rbeir'A-inch edges. Apply glue to The longer 1-inch-wide face of each rear piece and position it over the back panel, flush with the outside edge and bottom of the panel. Fasten each ti im piece with three 1'/a-inch finish nails. Apply glue To the inside face of each side trim piece and position it over a rear trim piece so their mitered ends are flush. Fasten the side trim to the box with Three 1'/s-inch finish nails (photo 5). Cut the base trim side and rear pieces to length. Apply glue to one face of the rear trim and fit it against the back, between the rear -corner trims and flush with the bottom of the base. Fasten The rear Trim with Three 1'/4-inch finish nails. Do the same with the two base trim side pieces, fitting them between the front- and rear -corner Trims. Prepare the Roof Deck Cut the two roof eave trim pieces to length. Glue the front (r/a-inch-wide) trim to the bottom (square) edge of one of the roof panels so it is flush with The rop face and aide edges of the panel; it will overhang The bortom face of the panel by about'/s inch. Fasten the trim with three 1'/a-inch finish nails, Glue and nail the rear (1Y inch -wide) cave trim to the other roof deck panel so the trim is flush with the top face and side edges of the panel, overhanging the bottom face. Apply glue to the top edges of The side panels. Fit the mof deck panels onto The side panels so they meet at 0. Tho gable trim covers the ends of the ewe trim. the roof deck, and the overlapping portions of the roofing boards. 9. Make opposing 1'/z -deep bevel cuts to create the V-groove in the roof cap. 10. Drill pilot holes al a 45° angle forjoiningihe mitered doorframe places wilh screws.