|
PER SCHED.PER SCHEDULE5"x20" CLEAR
<br />TEMPERED
<br />INSULATED
<br />GLASS
<br />PER SCHEDULE
<br />PER SCHEDULEFULL WIDTH CLEAR VISION PANEL
<br />3'-8"PUSH TO EGRESS
<br />SIGNAGE
<br />"D""E"
<br />PER SCHED.PER SCHEDULE"C"
<br />PER SCHED.PER SCHEDULE"A"
<br />PER SCHEDULE
<br />PER SCHEDULE"B"
<br />OVERHEAD COILING DOOR
<br />PER SCHEDULE
<br />8'-0""F"
<br />PER SCHED.
<br />"2"
<br />PER SCHED.PER SCHEDULE"1"PER SCHEDULEDOOR TYPESFRAME TYPES
<br />22"x30" CLEAR
<br />TEMPERED
<br />GLASS -
<br />INSULATED ON
<br />EXTERIOR
<br />DOORS
<br />REMOVABLE TRANSOM
<br />2'-0"DIVISION 08 -OPENINGS
<br />I. DOORS
<br />A. HOLLOW METAL DOORS (ANSI/SDI A250.8)
<br />1. CONSTRUCTION
<br />a. THICKNESS: 1 3/4 INCHES
<br />b. STEEL SHEET: ASTM A568
<br />1. CORROSION RESISTANT COATING
<br />a. HOT DIP GALVANNEALED: A60 PER ASTM A653
<br />b. MINIMUM ZINC-IRON ALLOY COATING: 0.6 OZ/FT2
<br />2. PROVIDE ABOVE CORROSION RESISTANT COATING AT DOOR AND FRAME COMPONENTS
<br />WHERE USED AT EXTERIOR AND INTERIOR WET AND HUMID LOCATIONS DEFINED BY THE
<br />FOLLOWING:
<br />a. EXTERIOR OPENINGS:
<br />1. OPENINGS LOCATED IN AN EXTERIOR WALL
<br />2. OPENINGS EXPOSED TO WEATHER EVEN IF PROTECTED BY A CANOPY
<br />3. OPENINGS USED FOR ROOF ACCESS
<br />b. INTERIOR OPENINGS
<br />1. OPENINGS TO AND FROM LOADING DOCKS AND TRASH COLLECTION AREA
<br />2. OPENINGS TO CONTROLLED ENVIRONMENTAL ROOMS
<br />3. PRIMER:
<br />a. CLEAN AND PHOSPHATIZE DOORS AND FRAMES
<br />b. ONE COAT OF BAKED-ON RUST INHIBITING PRIMER PAINT IN ACCORDANCE WITH
<br />ANSI A250.10
<br />c. SUITABLE AND COMPATIBLE AS BASE FOR SPECIFIED FINISH PAINTS
<br />c. HM DOOR LEVEL, PER ANSI A250.8
<br />1. LEVEL 4, MAXIMUM DUTY, PHYSICAL PERFORMANCE LEVEL A
<br />a. FACE SHEET THICKNESS: 0.067 INCHES (14 GA.)
<br />2. LEVEL 3, EXTRA HEAVY DUTY, PHYSICAL PERFORMANCE LEVEL A
<br />b. FACE SHEET THICKNESS: 0.053 INCHES (16 GA.)
<br />d. TYPICAL MODEL, PER ANSI A250.8
<br />1. MODEL 2, SEAMLESS
<br />e. END CLOSURES AT TOP AND BOTTOM OF DOOR
<br />1. TOP: FLUSH CLOSURE CAP. MINIMUM SHEET THICKNESS 0.032 INCHES (20 GA.)
<br />2. BOTTOM: FLUSH CLOSURE. MINIMUM SHEET THICKNESS 0.032 INCHES (20 GA.)
<br />f. CORES
<br />1. STEEL STIFFENERS WHERE STRUCTURALLY REQUIRED
<br />2. EXTERIOR DOORS:
<br />a. THERMALLY INSULATED CORE
<br />1. POLYSTYRENE
<br />2. MINIMUM R-VALUE: 5 WHEN TESTED ACCORDING TO ASTM C1363
<br />3. INTERIOR DOORS:
<br />a. NON-RATED DOORS: KRAFT HONEYCOMB LAMINATED TO FACE SHETS
<br />b. RATED DOORS: FIRE RESISTANT CORES AS REQUIRED BY LABEL
<br />c. WET/HUMID AREAS: MOISTURE RESISTANT MATERIALS; FIRE RESISTANT WHERE
<br />APPLICABLE
<br />g. VERTICAL DOOR EDGES
<br />1. LOCK STILE EDGES: BEVELED 1/8 INCH PER 2 INCHES
<br />a. EXCEPTION: FABRICATE IN-ACTIVE LEAVES: FABRICATE INACTIVE LEAVES WITH A
<br />SQUARE EDGE AT THE LOCK STILE EDGE.
<br />2. HINGE STILES EDGE: BEVELED 1/8 INCH PER 2 INCHES
<br />a. EXCEPTIONS FOR DOUBLE ACTING DOORS: PROVIDE CONVEX, RADIUSED EDGES
<br />AT LOCK STILES AND HINGE STILES
<br />h. HARDWARE REINFORCEMENT
<br />1. FABRICATE ACCORDING TO ANSI/SDI A250.6 WITH REINFORCEMENT PLATES FROM SAME
<br />MATERIAL AS DOOR FACE SHEETS
<br />2. MINIMUM THICKNESS: AS PRESCRIBED IN ANSI/SDI A250.6. UPGRADE AS NECESSARY FOR
<br />CONDITIONS SUCH AS DOOR WEIGHT, SIZE, FREQUENCY, ETC. AND AS FOLLOWS:
<br />a. BUTT HINGES: 0.167 INCHES (7 GA)
<br />b. CONTINUOUS HINGES: REINFORCE WITH 0.067 INCHES (14 GA) THICK x 1 1/4 INCH WIDE
<br />STRAPPING EXTENDING FULL HEIGHT AND WELDED TO HINGE EDGE OF DOOR
<br />c. CLOSERS AND OVERHEAD STOPS: 0.067 INCHES (14 GA)
<br />i. LITES
<br />1. PROVIDE LITE KITS WHICH ARE LABELED FOR INTENDED OPENING
<br />B.RAPID ROLL UP FABRIC DOORS
<br />1. BASIS OF DESIGN: ASI TECHNOLOGIES, CLEANSEAL DIVISION; MODEL 415 ISO-ROLL OR EQUIVALENT AS
<br />APPROVED BY ARCHITECT.
<br />2. COMPONENTS:
<br />a. SIDE FRAME COVERS: 304 STAINLESS STEEL
<br />b. DOOR MATERIAL: 0.040" THICK POLYESTER MULTIFILAMENT PVC COATED CURTAIN MATERIAL, FDA
<br />COMPLIANT. COLOR TO BE SELECTED FROM MANUFACTURERS STANDARD COLORS.
<br />c. VISION PANEL.
<br />d. TWO-WAY BREAK AWAY UPON IMPACT.
<br />e. STANDARD 304 STAINLESS STEEL, #4 DIRECTIONAL FINISH, FULL HEADER SHROUD.
<br />f. DOOR SPEED AND OPERATION: TWO SPEED OPERATION; 48 INCHES PER SECOND OPENING SPEED
<br />AND 21 INCHES PER SECOND CLOSING SPEED.
<br />g. SIZE: AS INDICATED ON DRAWINGS.
<br />3. ELECTRICAL OPERATION:
<br />a. ELECTRICAL CHARACTERISTICS:
<br />1. ELECTRIC MOTOR: SIZE AS RECOMMENDED BY DOOR MANUFACTURER FOR
<br /> SIZE AND TYPE OF DOOR; SELF DIAGNOSTIC CUSTOM MICROPROCESSOR WITH VARIABLE
<br /> FREQUENCY MOTOR DRIVE ALLOWING FOR FULLY ADJUSTABLE SPEED.
<br />2. ELECTRIC CONTROL PANEL: NEMA-4X RATED ENCLOSURE, WITH PUSH BUTTON EMERGENCY
<br />STOP, ASSEMBLED AND READY FOR CONNECTION BY OTHERS.
<br />3. 120 VOLT SINGLE PHASE POWER
<br />4. WIRING TERMINATIONS: PROVIDE TERMINAL LUGS TO MATCH BRANCH CIRCUIT CONDUCTOR
<br />QUANTITIES, SIZES, AND MATERIALS INDICATED. ENCLOSE TERMINAL LUGS IN TERMINAL BOX
<br />SIZED TO NFPA 70.
<br />5. SAFETY EDGE: FULL WIDTH AT BOTTOM OF DOOR PANEL, FREE OF RIGID STRUCTURAL
<br />PIECES. BOTTOM EDGE EQUIPPED WITH FLEXIBLE WIRELESS REVERSING EDGE. REVERSING
<br />EDGE SEALED WITHIN FULL WIDTH OF BOTTOM CURTAIN AND ACTIVATED ONLY WHEN
<br />PRESSURE IS APPLIED. REVERSING SIGNAL IS WIRELESSLY TRANSMITTED.
<br />a. PHOTO EYES: SEND AND RECEIVE PHOTO EYES, LOCATED WITHIN DOOR SIDE FRAME.
<br />b. PUSH BUTTON DOOR CONTROL: PIEZO PUSH BUTTON.
<br />c. HAND HELD RADIO CONTROL ACTUATOR: DIGITAL CONTROL, RESETTABLE (2 PER
<br />DOOR).
<br />4. INSTALLATION:
<br />a. INSTALL DOOR UNIT ASSEMBLY IN ACCORDANCE WITH MANUFACTURERS
<br />INSTRUCTIONS.
<br />b. SECURELY BRACE DOOR TRACKS SUSPENDED FROM STRUCTURE. SECURE TRACKS
<br />TO STRUCTURAL MEMBERS ONLY.
<br />c. COORDINATE INSTALLATION OF ELECTRICAL SERVICE. COMPLETE POWER AND
<br />CONTROL WIRING FROM DISCONNECT TO UNIT COMPONENTS.
<br />DIVISION 08 -OPENINGS -CONTINUED
<br />ND WIDTH: AS INDICATED ON DRAWINGS
<br />4. TEMPERED
<br />V. DOOR HARDWARE:
<br />A. PROVIDE ALL HARDWARE SPECIFIED IN DOOR AND HARDWARE SCHEDULE AND THESE SPECIFICATIONS OR AS
<br />REQUIRED TO MAKE DOORS FULLY FUNCTIONAL, COMPLIANT WITH APPLICABLE CODES, AND SECURE TO THE
<br />EXTENT INDICATED.
<br />B. PROVIDE ALL ITEMS OF A SINGLE TYPE OF THE SAME MODEL BY THE SAME MANUFACTURER.
<br />C. PROVIDE PRODUCTS THAT COMPLY WITH THE FOLLOWING:
<br />i. APPLICABLE PROVISIONS OF FEDERAL, STATE, AND LOCAL CODES.
<br />ii. ADA STANDARDS FOR ACCESSIBLE DESIGN.
<br />iii. ANSI/ICC A117.1, AMERICAN NATIONAL STANDARD FOR ACCESSBILE AND USABLE BUILDINGS AND
<br />FACILITIES.
<br />iv. APPLICABLE PROVISIONS OF NFPA 101, LIFE SAFETY CODE.
<br />vii. PRODUCTS REQUIRING ELECTRICAL CONNECTION: LISTED AND CLASSIFIED BY UL AS SUITABLE FOR THE
<br />PURPOSE SPECIFIED AND INDICATED.
<br />D. FUNCTION: LOCK AND LATCH FUNCTIONS AND DESCRIPTIONS AS LISTED IN DOOR AND HARDWARE SCHEDULE.
<br />E.ELECTRICALLY OPERATED AND/OR CONTROLLED HARDWARE INCLUDING DOOR INTERLOCKING: PROVIDE ALL
<br />POWER SUPPLIES, POWER TRANSFER HINGES, RELAYS, AND INTERFACES REQUIRED FOR PROPER OPERATION;
<br />PROVIDE WIRING BETWEEN HARDWARE AND CONTROL COMPONENTS AND TO BUILDING POWER CONNECTION.
<br />F. PROVIDE BHMA 630 BASE MATERIAL WITH US32D STAINLESS STEEL FINISH FOR ALL DOOR HARDWARE AT DOORS
<br />AND FRAMES.
<br />G. PROVIDE DOOR HARDWARE COMPATIBLE WITH THE DESIGN, MATERIALS, AND CONSTRUCTION OF ASSOCIATED
<br />DOOR AND FRAME.
<br />H. PROVIDE LOCK-TITE OR EQUIVALENT AT ALL SCREWS USED DURING INSTALLATION OF DOOR HARDWARE.
<br />I. PRODUCTS
<br />ITEM:MANUFACTURER:
<br />HINGES IVES
<br />CLOSERS LCN
<br />LOCKS AND CYLINDERS SCHLAGE
<br />FLUSHBOLTS AND ACCESSORIES IVES
<br />EXIT DEVICES VON DUPRIN
<br />ELECTRONICS VON DUPRIN
<br />W/S, THRESHOLD AND SWEEPS NGP
<br />J. HARDWARE SETS
<br />SET NUMBER 1 -
<br />DOORS TO HAVE;
<br />3 5BB1HW-652 NRP 4.5x4.5 HINGES
<br />1 99L-26D x 996L TRIM EXIT DEVICE
<br />1 6300-FSE-32D ELECTRIC STRIKE
<br />1 PS902-2RS POWER SUPPLY
<br />1 4050-SCUSH-AL X TBSRT CLOSER
<br />1 20-022-626 RIM CYLINDER
<br />1 160V-3070 WEATHERSTRIP
<br />1 425-3' X WS/PA THRESHOLD
<br />1 200NA-3'SWEEP
<br />1 16A-3'-4"DRIP EDGE
<br />1 679-05HM DOOR POSITION SWITCH
<br />SET NUMBER 2 -EXTERIOR DOORS -EXIT ONLY -NO ENTRY
<br />DOORS TO HAVE;
<br />EXIT DEVICES (PUSH BARS) WITH NO EXTERIOR HARDWARE
<br />CLOSER
<br />SET NUMBER 3 -
<br />DOORS TO HAVE;
<br />3 5BB1HW-652 4.5x4.5 HINGES
<br />1 99L-26D x 996L TRIM EXIT DEVICE
<br />1 20-022-626 RIM CYLINDER
<br />1 4050-CUSH-AL X TBSRT CLOSER
<br />1 20-022-626 RIM CYLINDER
<br />1 679-05HM DOOR POSITION SWITCH
<br />1 PS902-2RS POWER SUPPLY
<br />1 6300-FSE-32D ELECTRIC STRIKE
<br />SET NUMBER 4 -
<br />DOORS TO HAVE;
<br />3 5BB1HW-652 4.5x4.5 HINGES
<br />1 QEL9927L-26D x LBR x 996L EXIT DEVICE
<br />1 9927L-DT-26D x 996LDT EXIT DEVICE
<br />1 EPT10.SP28 POWER TRANSFER
<br />1 20-022-626 RIM CYLINDER
<br />1 679-05HM DOOR POSITION SWITCH
<br />1 4050-CUSH-AL X TBSRT CLOSER
<br />1 PS902-2RS POWER SUPPLY
<br />SET NUMBER 5 -
<br />DOORS TO HAVE:
<br />3 5BB1-652 4.5x4.5 HINGES
<br />1 ND10S-RHO-626 LEVER PASSAGE
<br />1 4050-CUSH-AL X TBSRT CLOSER
<br />1 WS406/407.630 WALL STOP
<br />SET NUMBER 6 -
<br />DOORS TO HAVE:
<br />3 5BB1-652 4.5x4.5 HINGES
<br />1 ND40S-RHO-626 LEVER PRIVACY
<br />1 4050-RW/PA-AL X TBSRT CLOSER
<br />1 8400 10 x 34.630 KICKPLATE
<br />1 WS406/407.630 WALL STOP
<br />SET NUMBER 7 -
<br />DOORS TO HAVE:
<br />6 5BB1-652 4.5x4.5 HINGES
<br />1PR FB458.626 FLUSHBOLTS
<br />1 DP2.626 DUST PROOF STRIKE
<br />1 ND80EU-RHO-626 ELECTRIC LEVER LOCKSET
<br />1 EPT10.SP28 POWER TRANSFER
<br />1 PS902-2RS POWER SUPPLY
<br />1 4050-RW/PA-AL X TBSRT CLOSER
<br />1 679-05HM DOOR POSITION SWITCH
<br />DIVISION 08 -OPENINGS RAPID ROLL UP FABRIC DOORS -CONTINUED
<br />C.OVERHEAD COILING DOOR
<br />1. COMPONENTS:
<br />a. CURTAIN (PROVIDE RATED CURTAIN WHERE FIRE RATED DOORS ARE INDICATED)
<br />1. 2 TO 3 INCH TALL SLATS, INTERLOCKED TO FORM AN UPWARD COILING CURTAIN
<br />2. NOMINAL THICKNESS: 3/4 INCHES
<br />3. GAUGE AS DETERMINED BY APPLICATION, WIND LOAD, DOOR WIDTH, AND MATERIALS
<br />4. TYPE OF MATERIAL AND FINISH AS INDICATED FOR EACH DOOR
<br />5. TYPICAL SLAT STYLE:
<br />a. INSULATED DOOR
<br />1. DOUBLE WALL SLATS INJECTED WITH POLYURETHANE FOAM
<br />2. THICKNESS: 15/16 INCH
<br />3. THERMAL VALUE: R-10.9 MINIMUM
<br />4. SLAT TYPE: FLAT, INSULATED, TYPE FIT-265
<br />5. BASE PRODUCT: STORMTITE AP MODEL 627 BY OVERHEAD DOOR; OR EQUAL
<br />2. FENESTRATED SLATS:
<br />a. PROVIDE ON DOORS WHERE INDICATED
<br />3. ENDLOCKS
<br />a. MINIMUM REQUIRMENT: PROVIDE MALLEABLE IRON ENDLOCKS AT EACH END OF
<br />ALTERNATING SLATS TO ACT AS A WEARING SURFACE AND TO MAINTAIN SLAT
<br />ALIGNMENT
<br />b. ENDLOCKS AT MOTORIZED DOORS: CONTINUOUS ENDLOCKS, (EVERY SLAT)
<br />c. ENDLOCKS AT EXTERIOR DOORS WHERE DOOR WIDTH EXCEEDS 12'-4": PROVIDE
<br />ROLLER ENDLOCKS WHERE ROLLER WINDLOCKS ARE REQUIRED
<br />4. BOTTOM BAR
<br />a. CURTAIN TO BE REINFORCED WITH BOTTOM BAR CONSISTING OF 2 BACK-TO-BACK
<br />ANGLES
<br />b. MATERIAL AND FINISHES: AS INDICATED FOR EACH DOOR TYPE, GENERALLY
<br />MATCHING THE CURTAIN MATERIAL AND FINISH
<br />c. NEOPRENE BOTTOM SEAL TO PROTECT FLOOR SURFACE AT SILL
<br />1. EXCEPT WHERE SAFETY EDGE IS INDICATED
<br />5. BRACKET PLATES
<br />a. MINIMUM THICKNESS: 1/4 INCH
<br />b. FITTED WITH SEALED BALL BEARING ON DRIVE END
<br />c. MATERIAL AND FINISH AS INDICATED FOR EACH TYPE OF DOOR
<br />6. SPRING COUNTERBALANCE
<br />a. HOUSED IN A STEEL PIPE OF DIAMETER AND WALL THICKNESS TO LIMIT DEFLECTION
<br />TO 0.03 INCHES PER FOOT.
<br />b. SPRINGS: HELICAL TORSION TYPE DESIGNED TO INCLUDE AN OVERLOAD FACTOR OF
<br />25% AND FOR EASE OF OPERATION
<br />c. MOTORIZED DOORS: UTILIZE HIGH CYCLE SPRINGS RATED AT 100,000 CYCLES
<br />1. SPRINGS TO BE GREASE PACKED AND MOUNTED ON A COLD-ROLLED STEEL INNER
<br />SHAFT
<br />2. SPRING TENSION: ADJUSTABLE FROM END OF BRACKET PLATE
<br />3. INCLUDE SAFETY DEVICE THAT PREVENTS FREE FALL OF CURTAIN IN ANY POSITION,
<br />IN THE EVENT OF FAILURE OF AN OPERATING MECHANISM
<br />4. SEALED BALL BEARINGS TO MINIMIZE WEAR OF PIPE SHAFT ROTATION AROUND INNER
<br />SHAFT
<br />7. MOUNTING:
<br />a. TYPICAL CONFIGURATION: FACE OF WALL (INSIDE).
<br />8. GUIDE ANGLES AND WALL ANGLE ASSEMBLIES
<br />a. MINIMUM THICKNESS: 3/16 INCHES
<br />b. PROVIDE ADEQUATE OVERLAP OF GUIDE FLANGES OVER CURTAIN TO SATISFY
<br />DESIGN WINDLOAD
<br />c. MATERIAL AND FINISHES: AS INDICATED FOR EACH DOOR TYPE
<br />d. INCLUDE REMOVABLE SECTION ON COIL SIDE FOR INSTALLATION AND SERVICE
<br />1. EXCEPTION: OMIT REQUIREMENT WHERE STAINLESS STEEL OR ALUMINUM
<br />GUIDES ARE SPECIFIED
<br />9. HOOD:
<br />a. TYPICAL PROFILE: ROUND
<br />b. REINFORCE TO PREVENT SAG
<br />c. INCLUDE INTERMEDIATE HOOD SUPPORTS WHERE DOOR WIDTH EXCEEDS 16 FEET
<br />d. MATERIAL AND FINISHES: AS INDICATED FOR EACH DOOR TYPE
<br />e. INCLUDE NEOPRENE HOOD BAFFLE AT DOORS USED ON THE EXTERIOR
<br />f. INCLUDE FLAME BAFFLE AT FIRE RATED OPENINGS
<br />g. OMIT HOOD WHERE DOOR COIL IS LOCATED ENTIRELY ABOVE THE CEILING (EXCEPT
<br />EXTERIOR DOORS AND FIRE RATED DOORS)
<br />10. FINISHES:
<br />a. GALVANIZED STEEL CURTAIN SLATS
<br />1. PRIMER: BAKED-ON PRIMER
<br />2. FINISH: POWDER COAT
<br />b. GALVANIZED STEEL BOTTOM BAR
<br />1. PRIMER: BAKED-ON PRIMER
<br />2. FINISH: POWDER COAT
<br />c. FERROUS STEEL WALL / GUIDE ANGLES
<br />1. SHOP COAT PRIMER
<br />2. PAINT IN FIELD
<br />d. FERROUS STEEL HOOD
<br />1. SHOP COAT PRIMER
<br />2. PAINT IN FIELD
<br />e. FERROUS STEEL END BRACKET PLATES
<br />1. SHOP COAT PRIMER
<br />2. PAINT IN FIELD
<br />f. FERROUS STEEL FASCIA
<br />1. SHOP COAT PRIMER
<br />2. PAINT IN FIELD
<br />11. MOTORIZED UNITS
<br />a. MANUFACTURER'S HEAVY DUTY, HIGH STARTING TORQUE MOTOR RATED FOR
<br />CONTINUOUS DUTY. SIZED TO MEET REQUIREMENTS
<br />b. COMPLY WITH UL 325
<br />c. OPENING RATE: BETWEEN 8 AND 9 INCHES PER SECOND
<br />d. GEAR REDUCTION
<br />e. SOLENOID BRAKING
<br />f. LIMIT SWITCHES FOR UPPER AND LOWER LIMITS OF DOOR TRAVEL
<br />g. MAGNETIC RELAY CONTACTOR
<br />h. OVERLOAD PROTECTION
<br />i. SAFETY SYSTEM
<br />1. WIRELESS ELECTRIC SAFETY EDGE
<br />a. CAUSES CURTAIN TO STOP AND REVERSE WHEN AN OBSTRUCTION IS
<br />ENCOUNTERED WHEN CLOSING
<br />b. SELF-MONITORING, WIRELESS
<br />c. DOORS WHICH ARE BOTH MOTORIZED AND USED ON EXTERIOR:
<br />USE COMBINATION ELECTRIC SAFETY EDGE DEVICE AND WEATHERSEAL
<br />j. BACK-UP OPERATION
<br />1. HAND CHAIN WITH ELECTRICAL INTERLOCK TO BREAK MOTOR CIRCUIT WHEN
<br />HAND CHAIN IS ENGAGED
<br />k. CONTROLS
<br />1. KEY ACTIVATED, FLUSH MOUNTED, 3 PUSH BUTTON CONTROL
<br />2. OPERATION
<br />a. "OPEN" BUTTON TO FULLY OPEN DOOR WHEN BUTTON IS DEPRESSED
<br />b. "CLOSE" BUTTON TO CLOSE DOOR WHEN BUTTON IS DEPRESSED
<br />c. "STOP" BUTTON STOPS DOOR IN EITHER DIRECTION
<br />3. INTERLOCK MOTOR SO THAT "CLOSE" BUTTON WILL BE DEACTIVATED WHEN
<br />DOOR IS IN FULL DOWN POSITION AND "OPEN" BUTTON WILL DE-ENERGIZE WHEN
<br />DOOR IS IN FULL OPEN POSITION
<br />4. ELECTRONIC INTERLOCK, WHICH DISCONTINUES THE MOTOR OPERATOR
<br />WHEN IT SENSES THAT THE CURTAIN HAS BEEN SECURED BY THE MECHANICAL
<br />LOCKING DEVICE
<br />5. CONTROL DEVICES: 1 PER OPENING
<br />DIVISION 08 -OPENINGS -CONTINUED
<br />II. FRAMES
<br />A.HOLLOW METAL FRAMES
<br />1. COMPLY WITH ANSI/SDI A250.8
<br />2. FABRICATE FRAMES WITH MITERED OR COPED CORNERS AND 1/2 INCH NOMINAL BACKBEND
<br />3. TOUCH-UP GALVANIZED / GALVANNEALED FRAMES WITH ZINC-RICH PRIMER
<br />4. FABRICATE FRAMES AS FACE WELDED
<br />a. FACE JOINTS: CONTINUOUSLY BACK WELD FACE JOINTS (WELD ON CONCEALED SIDE)
<br />b. FILL AND FINISH EXPOSED SIDES TO BE FREE OF VISIBLE SEAMS
<br />c. INTERSECTIONS OF RABBETS, STOPS, AND SOFFIT JOINTS: FABRICATE TO HAIRLINE JOINTS. STITCH
<br />WELD ON CONCEALED SIDE.
<br />d. SPLIT TYPE FRAMES AND KNOCK DOWN TYPE FRAMES ARE NOT ACCEPTABLE
<br />e. FASTENERS WHICH ARE EXPOSED TO VIEW ARE NOT ACCEPTABLE
<br />5. LITES:
<br />a. PROVIDE LIGHT KITS LABELED FOR INTENDED OPENING
<br />b. FIXED STOP:
<br />1. LOCATE AT EXTERIOR FACE
<br />2. INTEGRAL TO DOOR / FRAME
<br />c. REMOVABLE STOP:
<br />1. LOCATE ON INTERIOR FACE
<br />2. SNAP-IN STOPS OR STOPS SECURED WITH COUNTERSUNK PHILLIPS HEAD MACHINE SCREWS
<br />6. SILENCERS
<br />a. QUANTITY
<br />1. THREE ON STRIKE JAMB OF SINGLE DOOR FRAMES
<br />2. TWO PER DOOR FOR PAIR DOORS, LOCATE AT HEAD
<br />7. HARDWARE REINFORCEMENT
<br />a. FABRICATE ACCORDING TO ANSI/SDI A250.6 WITH REINFORCEMENT PLATES FROM SAME MATERIAL AS
<br />FRAMES
<br />b. MINIMUM THICKNESS: AS PRESCRIBED IN ANSI/SDI A250.6; UPGRADE AS NECESSARY FOR
<br />CONDITIONS SUCH AS DOOR WEIGHT, SIZE, FREQUENCY, ETC AND AS FOLLOWS:
<br />1. BUTT HINGES: 7 GA.
<br />2. CONTINUOUS HINGES: REINFORCE WITH 0.067 INCH (14 GA.) THICK x 1 1/4 INCH WIDE
<br />STRAPPING EXTENDING FULL HEIGHT AND WELDED TO HINGE JAMB DOOR RABBET OF FRAME
<br />3. CLOSERS AND OVERHEAD STOPS: 0.093 INCH (12 GA.) THICK x 12 INCH LONG STRAPPING
<br />WELDED TO VERTICAL FLANGE OF FRAME
<br />8. JAMB ANCHORS -ASTM A879 COMMERCIAL STEEL, 4 OZ/SF COATING; MILL PHOSPHATIZED. FRAMES BUILT
<br />INTO EXTERIOR WALLS; SHEET STEEL COMPLYING WITH ASTM A1008 OR ASTM A1011, HOT
<br />DIPPED GALVANIZED ACCORDING TO ASTM A153, CLASS B
<br />a. STUD FRAMED WALLS:
<br />1. Z-SHAPED CLIPS, WELDED TO INSIDE OF FRAMES; NOT LESS THAN 0.042 INCH (18 GA.) THICK
<br />2. ATTACH ANCHORS TO STUDS WITH SCREWS
<br />b. MASONRY WALLS:
<br />1. ADJUSTABLE STRAP-AND-STIRRUP OR T-SHAPED ANCHORS TO SUIT FRAME SIZE, NOT LESS
<br />THAN 0.042 INCH (18 GA.), WITH CORRUGATED OR PERFORATED STRAPS NOT LESS THAN
<br />2 INCHES WIDE x 10 INCHES LONG; OR WIRE ANCHORS NOT LESS THAN 0.184 INCHES (6 GA.)
<br />2. EMBED LONG LEG INTO MASONRY WALL AS IT IS LAID
<br />c. POST INSTALLED EXPANSION TYPE FOR IN PLACE CONCRETE OR MASONRY
<br />1. MINIMUM 3/8 INCH COUNTERSUNK, FLAT HEAD EXPANSION BOLTS WITH EXPANSION SHIELDS
<br />OR INSERTS
<br />2. INCLUDE PIPE SPACER FROM FRAME TO WALL, WITH THROAT REINFORCEMENT PLATE,
<br />WELDED TO FRAME AT EACH LOCATION
<br />9. FLOOR ANCHORS -SAME MATERIAL FOR JAMB ANCHORS BUT NOT LESS THAN 0.053 INCH (12 GA.) THICK
<br />a. MONOLITHIC CONCRETE SLABS: CLIP TYPE ANCHORS, WITH TWO HOLES TO RECEIVE FASTENERS
<br />b. TOPPED SLABS: ADJUSTABLE ANCHORS WITH EXTENSION CLIPS ALLOWING NOT LESS THAN 2 INCH
<br />HEIGHT ADJUSTMENT. TERMINATE BOTTOM OF FRAMES AT FINISH FLOOR SURFACE
<br />c. INCLUDE CONCEALED FASTENERS
<br />d. PROVIDE ANCHORS IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS ON FIRE RATED
<br />DOORS
<br />10. HEAD ANCHORS
<br />a. PROVIDE TWO HEAD FRAME ANCHORS FOR DOUBLE EGRESS FRAMES
<br />b. LOCATE AT THIRD POINTS OF SPAN
<br />11. SCHEDULE OF FRAMES
<br />a. STANDARD EXTERIOR FRAMES -0.067 INCHES (14 GA) -GALVANIZED / GALVANNEALED
<br />b. STANDARD INTERIOR FRAMES -0.053 INCHES (16 GA)
<br />c. FIRE RATED INTERIOR FRAMES -0.053 INCHES (16 GA)
<br />d. FRAMES FOR DOORS WITH AUTOMATIC OPENERS -0.067 INCHES (14 GA)
<br />e. FRAMES IN WET / HUMID AREAS -0.053 INCHES (16 GA)
<br />B. ALUMINUM FRAMES
<br />a. BASIS OF DESIGN: KAWNEER TRIFAB 451UT; OR EQUAL
<br />1. 4 1/2 INCH x 2" WITH THERMAL BREAK IN ACCORDANCE WITH AAMA TIR-A8 AND AAMA 505
<br />b. BRACKETS AND REINFORCEMENTS: MANUFACTURER'S STANDARD HIGH STRENGTH ALUMINUM WITH
<br />NONSTAINING, NON FERROUS SHIMS FOR ALIGNING SYSTEM COMPONENTS
<br />c. FASTENERS AND ACCESSORIES: MANUFACTURER'S STANDARD CORROSION-RESISTANT,
<br />NON-STAINING, NON-BLEEDING FASTENERS AND ACCESSORIES COMPATIBLE WITH ADJACENT
<br />MATERIALS. USE STAINLESS STEEL FASTENERS WHERE EXPOSED
<br />d. GLAZING: AS SPECIFIED IN THE GLAZING SECTION
<br />e. GLAZING SEALANTS -AS RECOMMENDED BY MANUFACTURER AND AS FOLLOWS:
<br />WEATHERSEAL SEALANT: ASTM C920 FOR TYPE S, GRADE NS, CLASS 25,
<br />USES NT, G, A, AND O; SINGLE-COMPONENT NEUTRAL-CURING FORMULATION THAT IS COMPATIBLE
<br />WITH STRUCTURAL SEALANT AND OTHER SYSTEM COMPNENTS WITH WHICH IT COMES IN CONTACT.
<br />III. GLAZING
<br />A.EXTERIOR GLASS AND GLAZING
<br />1. GLASS TYPES
<br />a. GLASS TYPE EXT-1:
<br />1. INSULATING GLASS; TWO SHEETS OF 1/4 INCH THICK GLASS, HERMETICALLY SEALED
<br />TOGETHER AT EDGES WITH SPACERS AND SEALANT, WITH 1/2 INCH DEHYDRATED AIR
<br />SPACE.
<br />2. OUTSIDE GLASS: 1/4 INCH THICK, SOLARBAN 90; OR EQUAL
<br />3. INSIDE GLASS: 1/4 INCH THICK, HEAT STRENGTHENED FLOAT GLASS, CLEAR, WITH
<br />LOW E COATING ON INSIDE SURFACE
<br />b. GLASS TYPE TYPE EXT-2:
<br />1. SAME AS EXT-1, TEMPERED BOTH LITES
<br />c. GLASS TYPE EXT-3: SPANDREL GLASS
<br />1. INSULATING GLASS; TWO SHEETS OF 1/4 INCH THICK GLASS, HERMETICALLY SEALED
<br />TOGETHER AT EDGES WITH SPACERS AND SEALANT, WITH 1/2 INCH DEHYDRATED AIR
<br />SPACE.
<br />2. OUTSIDE GLASS: 1/4 INCH THICK, SOLARBAN 90; OR EQUAL
<br />3. INSIDE GLASS: 1/4 INCH THICK, HEAT STRENGTHENED FLOAT GLASS, CLEAR, COATED ON
<br />ONE
<br />SIDE WITH OPAQUE CERAMIC COATING
<br />B.INTERIOR GLASS AND GLAZING
<br />1. GLASS TYPES
<br />a. GLASS TYPE A -ANNEALED:
<br />1. CLEAR FLOAT, 1/4 INCH THICK
<br />b. GLASS TYPE T -TEMPERED:
<br />1. CLEAR, FULLY TEMPERED TONGUE-LESS FLOAT, 1/4 INCH THICK
<br />c. GLASS TYPE INT-1: LAMINATED FIRE AND SAFETY GLASS
<br />1. LAMINATED, WIRELESS, UL LABELED FOR ASSEMBLY INDICATED
<br />2. IMPACT -SAFETY RATED PER ANSI Z97.1 AND CPSC 16CFR1201
<br />3. THICKNESS -5/16 INCH THICK, LAMINATED
<br />4. SURFACE -POLISHED
<br />5. BASE PRODUCT -FIRELITE PLUS BY TECHNICAL GLASS PRODUCTS; OR EQUAL
<br />d. GLASS TYPE M -MIRROR GLASS
<br />1. COLOR: CLEAR
<br />2. THICKNESS: 1/4 INCH THICK
<br />3. UNIT LENGTH AND WIDTH: AS INDICATED ON DRAWINGS
<br />4. TEMPERED
<br />PROJECT NUMBER:
<br />jedson.com
<br />One Centennial Plaza
<br />705 Central Ave
<br />Cincinnati, OH 45202
<br />P: 513.965.5999
<br />F: 513.965.5998
<br />THIS DRAWING AND ITS RELATED COPYRIGHTS, INTELLECTUAL PROPERTY RIGHTS AND TRADE SECRETS ARE THE PROPERTY OF JEDSON
<br />ENGINEERING, INC. AND CONTAINS CONFIDENTIAL INFORMATION, WHICH SHALL NOT BE USED, COPIED OR DISCLOSED WITHOUT WRITTEN PERMISSION
<br />OF JEDSON ENGINEERING, INC. ©2013 JEDSON ENGINEERING, INC. ALL RIGHTS RESERVED.
<br />1
<br />2
<br />3
<br />4
<br />5
<br />6
<br />7
<br />8
<br />9
<br />1
<br />2
<br />3
<br />4
<br />5
<br />6
<br />7
<br />8
<br />9
<br />ABCDEFGHKLM
<br />REVISIONS
<br />ABCDEFGHJKLM
<br />PROJ. NO.:
<br />DRAWN BY:
<br />CHECKED BY:
<br />APPROVED BY:
<br />SCALE:11/4/2021 1:10:44 PMApprover
<br />Checker
<br />Designer
<br />200199
<br />McCORMICK & COMPANY
<br />DOOR SCHEDULESB-A502SB-A502 -I
<br />200199
<br />DOOR SCHEDULE
<br />DOOR
<br />NUMBER
<br />DOOR FRAME
<br />HARD
<br />WARE
<br />FIRE
<br />RATING
<br />INTERLOCK
<br />ED WITH COMMENTSTYPEWIDTHHEIGHTTHICKNESSMATERIALFINISHGLAZINGTYPEMATERIALFINISH
<br />140A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 1
<br />140B A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 1
<br />140C A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 1
<br />140D C 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 2 HOLLOW METAL PAINT 5 -
<br />141A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 3
<br />142A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 1 HOLLOW METAL PAINT 1
<br />142B B 30'-0" 15'-0" 3/4" GALVANIZED STEEL - GALVANIZED STEEL OVERHEAD COILING DOOR
<br />142C C 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 2 HOLLOW METAL PAINT 1 -
<br />143 V 3'-0" 8'-0" 1 3/4" HOLLOW METAL PAINT - 2 HOLLOW METAL PAINT 7 DOUBLE DOORS
<br />144 A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 3
<br />147A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 5
<br />147B A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 5
<br />148A C 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 2 HOLLOW METAL PAINT 3 -
<br />148B B 9'-0" 10'-0" 3/4" GALVANIZED STEEL - STAINLESS STEEL OVERHEAD COILING DOOR
<br />149A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 5
<br />149B E 8'-0" 8'-0" FABRIC - - STAINLESS STEEL -RAPID ROLL DOOR WITH VISION WINDOW
<br />149C A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 1
<br />150A A 3'-0" 6'-8" 1 3/4" HOLLOW METAL PAINT X 2 HOLLOW METAL PAINT 5
<br />150B B 8'-0" 8'-0" 3/4" GALVANIZED STEEL -OVERHEAD COILING DOOR
<br />151A A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 1 HOLLOW METAL PAINT 5
<br />151B A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 1 HOLLOW METAL PAINT 5
<br />151C E 9'-0" 10'-0" FABRIC X STAINLESS STEEL RAPID ROLL DOOR WITH VISION WINDOW
<br />151D A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 1 HOLLOW METAL PAINT 5
<br />151E A 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT X 1 HOLLOW METAL PAINT 5
<br />151F JJ 10'-0" 10'-0" FABRIC -RAPID ROLL DOOR WITH VISION WINDOW
<br />152 C 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 1 HOLLOW METAL PAINT 5
<br />153 C 3'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 1 HOLLOW METAL PAINT 6
<br />201 F 6'-0" 7'-0" 1 3/4" HOLLOW METAL PAINT - 2 HOLLOW METAL PAINT 3 DOUBLE DOORS
<br />3425 LATHROP ST. SOUTH BEND, INDIANA 46628
<br />NO DESCRIPTION DATE DB CB AB
<br />B LAYOUT D 7/13/2021 DLR DLR
<br />C LAYOUT E 8/3/2021 DLR DLR
<br />D LAYOUT PROGRESS 8/11/2021 DLR DLR
<br />E LAYOUT G 8/25/2021 DLR DLR
<br />F REVISIONS 9/14/2021 DLR DLR
<br />G GENERAL REVISIONS 9/20/2021 DLR DLR
<br />H GENERAL REVISIONS 10/1/2021 DLR DLR
<br />I ISSUED FOR REVIEW 11/01/2021 DLR DLR
|