My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - Crossroads Ambulance Sales & Service, LLC
sbend
>
Public
>
Public Works
>
Board of Works Documents
>
2020
>
Opening of Bids
>
Opening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - Crossroads Ambulance Sales & Service, LLC
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
11/12/2020 11:15:42 AM
Creation date
11/12/2020 11:14:10 AM
Metadata
Fields
Template:
Board of Public Works
Document Type
Contracts
Document Date
11/10/2020
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
210
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
Show annotations
View images
View plain text
2021 International MV/PL Custom Titan 170 <br />Type I Ambulance Proposal Specification <br /> <br /> <br />A5347-0002 11/05/20 <br />8 <br /> <br />designed for hinged doors. It shall be a "Dynamic" type seal with vent holes on the outside edge to allow for easier closing <br />of door against seal. Flat open or closed cell solid rubber "Static" seals are not acceptable for hinged doors. <br /> <br />DOOR HINGES: <br /> <br />Each door shall be hung with stainless steel continuous hinges. The hinge shall have a 1/4" pin which is staked every six <br />inches to prevent the pin from sliding. The hinges shall be held to the door and to the body using 1/4-20 stainless steel <br />threaded machine fasteners every, 4" on both sides, use of rivets on hinges is not acceptable. All hinges installed on the <br />body shall include a closed cell foam barrier between the dissimilar stainless steel hinge surface and the painted <br />aluminum body. A close cell gasket shall be added between hinge and body to seal any gaps caused by securing the <br />hinge. <br /> <br />DOOR LATCH HARDWARE: <br /> <br />Every door shall utilize an automotive type rotary slam latch. All doors used for personnel access shall utilize two latches ; <br />one located on the top of the door the other at the bottom. All compartment doors taller than 70" shall utilize two latches; <br />one located on the top of the door and the other at the bottom. Single point hardware for this type or any other type of <br />door hardware is unacceptable. The latches shall meet FMVSS 206 standard and shall not be modified in any way to <br />jeopardize its integrity. Latch pins without heads intact shall be cause for immediate rejection of vehicle. <br /> <br />All rotary slam latches shall be activated by adjustable steel rods. Cable activated rotary latche s are unacceptable. All <br />door hardware and rod assemblies shall be designed to minimize hardware rattle. <br /> <br />Compartments that require double opening doors shall incorporate (2) point latches on first closing door in addition to <br />second closing door. The latches shall be activated by a handle in each compartment door on the exterior which matches <br />the other exterior handles on the vehicle. <br /> <br />All door hardware, including rods and latches, shall be concealed within the inner door panel. Doors with any exposed <br />latching hardware are unacceptable. <br /> <br />All door systems, including latches, hinges and body/door components shall be tested and certified to meet AMD -002. <br />Test documentation shall be provided upon request. <br /> <br />ANODIZED ALUMINUM DRIP MOLDINGS: <br /> <br />Anodized extruded aluminum drip moldings shall be provided above all exterior compartment and entrance doors. The <br />moldings shall be attached without the use of unsightly screws and shall be easily replaceable if damaged. This molding <br />shall direct excess water away from the compartment and entrance door opening. <br /> <br />COMPARTMENT DOOR BUMPERS: <br /> <br />Heavy duty tape on type rubber (Styrene butadiene rubber, SBR) bumpers shall be installed on all compartments that <br />may come in contact with one another. <br /> <br />LOCKTITE/FASTENERS: <br /> <br />All exterior door hinge bolts, inner door panels on both compartment and entrance door panel, and door latching bolts <br />shall be installed with the use of Locktite thread locking material.
The URL can be used to link to this page
Your browser does not support the video tag.