Laserfiche WebLink
11/09/2020 Page 6 <br />PART NO S DESCRIPTION QTY <br />02-B0-CC08 |-- Compartment Door Panel: Diamond Plate 112-DC-GA10 |-- Compartment Finish: Diamond Plate Standard 1 <br />02-B0-CC13 < |-- Compt Venti - Compartment Ceiling O O O O and Square Holes Horiz <br />ARV STYLE <br />1 <br />MTB NOTE: hat channel with three (4") holes above the hat at the ceiling level. >> Additional Horizontal square holes in out facing vertical hat channel. <br />02-B0-SWFL |-- Compt Floor: Sweep-out, even with bottom door jamb.102-B0-CC41 |-- Compartment floor thickness .125" standard 1 <br />02-BC-10A5 |-- Compartment Door: SINGLE DOOR, Forward hinged 2-point Latch 1 <br />02-B0-09B0 |-- Compt Door Check: Double Action Gas Shock 104-EA-09B1 |-- Door Swing Angle: Set to 90-100 degrees 1 <br />04-TS-19M5 S < |-- M-5 Divider, Fixed, (1) 14x60 H 1 <br />Divider to be Located Approx. 10" From Wall #1 as Close to Stair Chair Pull Out Tray <br />as Possible. <br />02-B0-CFN1 S |-- Component Finish (Divider & Shelf): Speedliner Black Each 2 <br />04-TS-1001 |-- Divider Material: .125 Aluminum Sheet 1 <br />04-TS-1200 S< |-- M-5 Shelf, Adjustable, Ext: .125 Aluminum, Partial Width 2" lips upward 1 <br />NOTE: Adj. Shelf to be From Divider to Wall #3 Above Stair Chair Slide Out Tray <br />04-TS-4010 |-- Shelf Bracket: CPI 90 Deg with Slotted Holes 1 <br />04-TS-2110 S< |-- Stair Chair Tray, Roll-out: Std Duty .125 Thick tray, Fixed position 1 <br />NOTE: Mounted on Wall #3 and Tray to store the stair chair in an upright position with <br />Lip around bottom of tray. <br />To be constructed .125 Aluminum Speed Lined Black <br />02-B0-CFN1 S |-- Component Finish (Stair Chair Holder): Speedliner Black Each 1 <br />04-TS-21A2 S< |-- Slides: Pair of Accuride AH760 250 lb 18" Full Extension with Top Slide <br />locking <br />1 <br />One locking slide with yellow thumb catch release <br />(1) SLID-9301Non-locking <br />(1) SLID-9308 Top Slide Locking typical 18" <br />04-TS-STR3 S< |-- Strap: 2" Webb, w/ Chrome Metal Seatbelt buckle w footman loops IATS 1 <br />This strap is to secure things from moving while the vehicle is in motion, and is not <br />designed to be a crash stable securing device. <br />Strap Installed on Stair Chair Tray to Hold Stair Chair <br />04-TS-STR2 S |-- 2" Footman Loops 1 <br />04-TS-STR8 S< |-- Straps: (2), 2" Webb, w/ Quick Release Seatbelt style Buckle, IATS 1 <br />(1) From Divider to Wall #1 40" Up From Floor <br />(1) From Divider to Wall #3 54" Up From Floor Above Shelf <br />This strap is to secure things from moving while the vehicle is in motion, it is not <br />designed to be a crash stable securing device. <br />04-TS-STR2 |-- 2" Footman Loops: Locate back from jamb 205-EL-40X5 < <br /> |-- Light, Compt, LED, M-5 (RR): Intertek Model No ZY-156-LEDC, STD 1 <br />MTB Note: 1" Hole, Centered in Compartment ceiling <br />05-EL-49X2 S < |-- Light, Compartment: LED, Intertek #ZY-156-LEDC X-Series, IATS 1 <br />MTB Note: No light hole required <br />ON BOTTOM OF SHELF <br />09-ZZ-ZZZZ |--1 <br />02-M1-X600 |-- M-6 Compt (RRFwd): Delete 1 <br />02-M1-M7N5 |-- M-7 Compt (RF): None 1