Laserfiche WebLink
VL-G I-J3I VA J I—0'1V-VVdJIr. IVWIVC <br />02-B1-ELEH < I-- Electrical Compartment: Circuit Board Storage relocated to cabinet H <br />02-BC-10DO I-- Doors, Compartment, DOUBLE DOORS (std) <br />02-BO-09B0-- Compt Door Check: Double Action Gas Shock <br />04-EA-09131 I-- Door Swing Angle: Set to 90-100 degrees <br />04-TS-11 D3 I-- M-2 Shelf, Adjustable, Ext:.125 Alum, 2" Upward lip <br />04-TS-4010 1— Shelf Bracket: CPI 90 Deg with Slotted Holes <br />05-EL-40X2 < I-- Lights, (2) Compartment: Kinequip #KSLC8 8", Strip Light, M-2, STD <br />MTB Note: No light hole required <br />(1) on ceiling, centered near door jamb, on angled bracket and (1) on Wall #3, near door <br />jamb, on angled bracket, to illuminated under shelf. <br />05-HB-1335 <br />< I-- Condenser, 12V: Pro -Air Dual Fan, FRKG 126 under the module body Included <br />1 <br />70,000 BTU <br />04-HA-1300 <br />1— Condenser Brackets: Under M-2, angled down <br />1 <br />06-RR-13ZO <br />I-- Standard Conduit: 1-1/2"", with pull wire <br />1 <br />06-RR-1304 <br />S I-- CONDUIT ORIGINATION POINT: M-1A compartment <br />1 <br />06-RR-13T3-- <br />CONDUIT TERMINATION POINT: Behind A/A Board (Panel) <br />1 <br />09-ZZ-ZZZZ-- <br />1 <br />02-1142-X364 <br />S< 1-- M-3 Compt (LR): 63.5" H x 43" W x 20.O" D <br />1 <br />WILL NARROW TELEMETRY AREA, LP WILL NOT FIT <br />02-BO-CCO2 <br />< I-- Compartment Construction: STANDARD Diamond Plate <br />1 <br />Sides and Back: .100 Polished Aluminum Diamond Plate <br />Compartment Ceiling: .090 Aluminum Sheet <br />02-BO-CC08-- <br />Compartment Door Panel: Diamond Plate <br />1 <br />12-DC-GA10-- <br />Compartment Finish: Diamond Plate Standard <br />1 <br />02-BO-SWFL <br />I-- Compt Floor: Sweep -out, even with bottom doorjamb. <br />1 <br />02-BO-CC41 <br />I-- Compartment floor thickness .125" standard <br />1 <br />02-BC-1000-- <br />Compartment Doors: DOUBLE DOORS, ILOS single <br />1 <br />02-BO-09BO <br />I-- Compt Door Check: Double Action Gas Shock <br />1 <br />04-EA-09B1 <br />I-- Door Swing Angle: Set to 90-100 degrees <br />1 <br />04-TS-11B4 <br />1— (2) Shelves, Adjustable, Ext..125 Aluminum, 2" Upward Lips IATS <br />1 <br />04-TS-4010 <br />I-- Shelf Bracket. CPI 90 Deg with Slotted Holes <br />2 <br />04-TS-1016 <br />XS < I-- Tool plate on uni-strut, .25 Smooth Aluminum/DA sanded in compartment <br />1 <br />Location BOTTOM PORTION OF M3 COMPT <br />24" HIGH AND FULL WIDTH <br />TOOL PLATE TO BE .25" <br />05-EL-40X3 < I-- Light, Compt, LED, M-3 (LR): Intertek Model No ZY-156-LEDC, STD <br />MTB Note: 1" Hole, Centered in Compartment ceiling <br />05-EL-49X2 S < I-- Light, Compartment: LED, Intertek #ZY-156-LEDC X-Series, IATS 2 <br />MTB Note: No light hole required <br />(1) ON BOTTOM OF EACH SHELF <br />09-ZZ-ZZZZ 1-- 1 <br />02-M1-X572 S I-- M-5 Compt (RR): 72 HR, 84.5" H x 21 " W x 22.0" D 1 <br />02-130-CCO2 < I-- Compartment Construction: STANDARD Diamond Plate 1 <br />Sides and Back: .100 Polished Aluminum Diamond Plate <br />Compartment Ceiling: .090 Aluminum Sheet <br />