Opening of Bids - Spec L - One or More 2018 or Newer 3 1-2 Ton Utility Truck with Crane - Truck Centers, Inc

Home Browse Search

F'ffled �iri Plumbing all hydraulic plumbing to conform to SAE standards. All pressure, return and suction hoses to utilize swivel fittings on both ends for ease of maintenance. Suction hose shall be —20 10OR4, pressure hose —8 10OR2, return hose —12 10ORI . Hoses to be F71Yes FINo supported every 24" minimum with rubber covered steel clamps. Consideration shall be taken to chafing and routing around corners and hoses must be properly sleeved with abrasion sleeve. Cooler: System will include an oil cooler equipped with a twelve- (12), volt fan and thermal bypass. The cooler will be sized to maintain oil temperature below 150 degrees F�,Yes FjNo F under full load for one hour at 199 degrees F ambient temperature. Hydraulic Tools: The following Hydraulic tools shall be provided with the unit upon [DYes F_1No delivery: Trash Pump: There shall be a hydraulic 3" trash pump provided with the body. Pump shall be similar to the one in use by the Water Department now (Stanley TP03). Pump EjYes [:]No must be capable of 800 gpm. Hydraulic drill: There shall be a hydraulic drill included with the unit. Drill shall be F7Yes [:]No equal to a Stanley HD45. Crane: There shall be a hydraulic crane mounted on the passenger side The crane shall be a pedestal mounted service crane that operates from the Vanair V3 multi -drive system. It shall have a single line capacity of 2250 lbs. and a 450�O lb� []Yes EjNo capacity with a two part line. The maximum overturning moment rating shall be 18,000, ft. lbs, HYDRAULIC REQUREMENTS: The crane shall have an open center system that operates on 1-3/4 GPM (non -proportional) or 3-1/2 GPM (prop�ortional) at 3000 psi. The hydraulic reservoir shall have an 8 gallon capacity with a 100 mesh suction filter. FY, Yes [:]No The hydraulic system shall include a 10 micron return filter. The valve block shall include valve coils with manual overrides for each function, TELESCOPIC BOOM: The boom shall telescope to provide a horizontal reach range of 8 ft. to 16 ft, using a 4 ft, hydraulic power extension section and a 4 ft, manual extension section, The power extension boorn shall have bearing pads on all sides made [ZlYes [:]No from UHMW polyethylene to provide low friction and wear rate without the use of lubricants. POWER EXTENSION: The boom shall be extended by a double-acting hydraulic cylinder with an integral counterbalance valve to prevent the boom from retracting should a loss of hydraulic pressure occur. The cylinder shall be mounted inside of the E]Yes ONo boom. The extension speed shall be 12 ft./min, at 1-3/4 GPM (non -proportional) or 24 ft/min at 3-1/2 GPM (proportional) BOOM ELEVATION: The boom elevation angle range shall extend from 8 degrees below horizontal to 75 degrees above horizontal. The boom shall be elevated by a 1AYes E]No double-acting hydraulic cylinder with an integral Counter balance valve to prevent the boom from lowering should a loss of hydraulic pressure. SHEAVES: The boom end load hoisting sheave shall be made of polyrner composite material and have a pitch diameter of at least 18 tirries the 5/16 wire rope diameter per ANSI B30.5, Sheave bearings shall be made of maintenance free composite niaterial. MYes E]No HYDRAULIC WINCH: The winch shall have a high efficiency planetary gear reduction with a spring applied -hydraulic released multi -disk brake with spring and shall be driven by a hydraulic gear motor. The winch line capacity shall be 2300 lbs. on MYesE]No the first layer with a line speed of approximately 52 ft./min. at 3-1/2 GPM (26 ft,/rnin. at 1-3/4 GPM). WINCH DRUM: Winch _�drurri first —layer wi�e rope pitch diameter shall be at least 18 tinics the 5/16 wire rope diameter per ANSI 1330.5. The winch drum shall be at least 6 E]Yes DNo in, wide between