Loading...
HomeMy WebLinkAbout629 Portage Avenue_AA 2026-0910Sarah Andrews, President HISTORIC PRESERVATION COMMISSION OF SOUTH BEND AND ST. JOSEPH COUNTY CERTIFICATE OF APPROPRIATENESS The Historic Preservation Commission of South Bend and St. Joseph County has approved the following work: Tear off existing asphalt shingle roof and replace with new asphalt shingles. *No work to be done on soffit, facsia or gutters* A&M HOME SERVICES, Contractor for the following location: 629 PORTAGE AVE South Bend, IN, 46616 Chapin Park Application No. 2026-0910 in the County of St. Joseph; State of Indiana; which is: Located in a Local Historic District A Local Historic Landmark and found this application to be appropriate according to the Standards pertaining to Local Historic Landmarks and/or Local Historic Districts. Regulations pertaining to the Historic Preservation Commission are found in Chapter 21 (Zoning), South Bend Municipal Code and Chapter 26 of the St. Joseph County Code. The issuance of this certificate does NOT in any manner, release the recipient from the responsibility of complying with the requirements of the zoning ordinances, building codes, safety codes, ADA or other requirements of the City of South Bend, the County of St. Joseph, the State of Indiana, or the United States Federal Government. This certificate is good for one year from the date of issuance and is effective from the date entered herein. Plans are on file and open for public inspection at the office of the Historic Preservation Commission of South Bend and St. Joseph County, 227 West Jefferson Blvd., Suite 1400 S, South Bend, Indiana, during normal business hours. THIS CERTIFICATE IS NOT TRANSFERABLE NAME OF APPLICANT:Michael Gerencser CERTIFICATE ISSUED BY: Ross Van Overberghe Historic Preservation Administrator POST IN A CONSPICUOUS PLACE ON THE STREET SIDE OF THE PROJECT UNTIL COMPLETION OF ALL WORK. Phone: (574) 235-9371 E-mail: SBSJCHPC@southbendin.gov ROSS VAN OVERBERGHE Historic Preservation Administrator 9/25/2026DATE CERTIFICATE TAKES FORCE:9/25/2027DATE CERTIFICATE EXPIRES: Ord No. 9574-05 Chapin Park ADMINISTRATIVE APPROVAL Thursday, September 10, 2026 Application for Certificate of Appropriateness Important Information Regarding this Request REQUIRED DOCUMENTATION AND SITE PLANS The Historic Preservation Commission of South Bend and St. Joseph County cannot process an Application without required documentation. Comprehensive documentation provides a complete understanding of the project. Problems often occur during a project review or during the execution of the project when the property owner, staff or commissioners are unclear as to project specifics. Applications will NOT be processed without required documentation. Photographs may be submitted in digital format or in photographic print. When a project involves blueprints and/or site plans, one (1) set shall be submitted with the Application. Any documentation submitted to this office cannot be returned to the applicant. APPLICATION FEE The application processing fee for any Application for a Certificate Of Appropriateness is $20 Payment must accompany the application at the time of submission. For an electronically submitted application, payment must reach the HPC office within 48 hours following transmission. Payment can be made by credit card by contacting Business License Administrator Michelle Adams at (574) 235-5912; by cash in person in the Department of Community Investment on the 14th floor of the County City Building; or by check made out to City of South Bend. Applications will NOT be processed without the required fee. MEETING ATTENDANCE When an Application has been scheduled for any meeting, the owner, architect or contractor(s) retained for the project shall attend the meeting where their project will be reviewed and a decision rendered. Failure by the owner, architect, or contractor to attend such meetings may result in denial of the Application due to insufficient representation. CERTIFICATE ISSUANCE Certificates of Appropriateness will be filed with the Building Department of South Bend and St. Joseph County. A copy of the Certificate will be emailed directly to the owner and/or contractor(s) listed on the application. INSPECTION AUTHORITY All projects will be inspected during and following execution for compliance with the decision(s) rendered by the Historic Preservation Commission of South Bend and St. Joseph County. 1 Owner acknowledges that while the Historic Preservation Commission only considers Certificates of Appropriateness for exterior features, under certain circumstances it may be necessary for the Commission Staff to have access to the interior of the building in order to accurately assess the condition of the exterior feature and that the lack of access to the interior may prevent the Commission Staff from making a favorable recommendation. Any work performed on a historic landmark or in an historic district which does not conform to the Certificate of Appropriateness certificate shall be immediately halted by the Historic Preservation Commission and the Building Department of South Bend and St. Joseph County. Fines may be levied for projects not in compliance. I read and understand the information above:Yes, Continue Date Thursday, September 10, 2026 2 Property Information Property Address for Proposed Work:629 Portage Ave Property City south bend Property Zip Code 46616-1356 Property Owner Information:Mike Gerencser Owner Email Owner Address 629 Portage Ave South Bend In 46616-1356 Proposed Work and Project Information All projects must comply with applicable building and zoning codes. South Bend Zoning Ordinance St. Joseph County Zoning Ordinance Does your project involve any of the following? (Check all that apply):Roofs Contractor Information A&M Home roof trisha RYNEARSON Contractor Phone Number (574) 855-1050 Contractor Email trisha@callamnow.com Description of Proposed Work: Re roof with IKO shingles. Full tear off with I&W File Upload Site Plans, Aerial Views, and/or Blueprints: One (1) set shall be submitted with the Application. Uploaded documentation must show existing property lines, buildings, structures, and proposed project location(s). Hand Drawn Plans/Elevations are ok Photographs to include: each area affected by project, close up detail of project areas. Windows, Siding, and/or Door projects must include photographs of each window/door/siding affected by the project and detailed close up of condition Applications will not be processed if the required photographs and/or documentation are not included. Any documentation submitted to this office cannot be returned to the applicant. Project Type - List:Roofs 3 September 22, 2026 MA CK No. 1645 $20.00 Overhead View of Proposed Project Location(s):PDF all_star_home_services_inc._dba_a_m….pdf Quote/Evaluation(s) by Repair Professional (Optional): PDF all_star_home_services_inc._dba_a….pdf Photographs: PDF 783008c9-de32-4932-9a83-c5e9a351….pdf Payment Invoice ID # INV-000289 Payment Method Pay via Check in Mail 4 A&M Home Services, Inc. 602 East Jefferson ST , Plymouth, Indiana 46563 (574) 855-1050 IMG_3465.jpeg Photo Taken Date: Thursday, August 13, 2026 2:29 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3459.jpeg Photo Taken Date: Thursday, August 13, 2026 2:28 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3457.jpeg Photo Taken Date: Thursday, August 13, 2026 2:28 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3453.jpeg Photo Taken Date: Thursday, August 13, 2026 2:28 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3448.jpeg Photo Taken Date: Thursday, August 13, 2026 2:27 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3441.jpeg Photo Taken Date: Thursday, August 13, 2026 2:22 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3438.jpeg Photo Taken Date: Thursday, August 13, 2026 2:20 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 IMG_3426.jpeg Photo Taken Date: Thursday, August 13, 2026 2:19 PM Upload Date: Thursday, August 13, 2026 2:53 PM Uploaded By: Eric Teall 11101-11488: Mike Gerencser Job Location: 629 Portage Avenue South Bend, IN 46616-1356 We can help you with Roofing, Waterproofing & Gutters Jared@callamnow.com (Sales Director) 574-855-1050 IKO ROOFING QUOTE AUG 13, 2026 MIKE GERENSCER 629 Portage Avenue, South Bend, IN, US, 46616-1356 INTRODUCTION Hi Mike , We recognize that safeguarding the people and possessions that hold the most value to you is of utmost importance. Your roof serves as the primary shield against the forces of nature, shielding your home from the elements and ensuring that everything inside remains safe and dry. Thank you for the opportunity to quote on the repairs and improvements to your home. Please find your estimate below along with upgrade options for potential improvements to your project, if applicable. The following estimate is for: 1. Remove and disposal of old materials 2. Supply and install new materials 3. Clean up of entire work area (all nails and other materials) 4. We are fully licensed to work in your location Once the job is complete, one of our Quality Control Officers from our Audit Division inspects your project to make sure we did everything correct and up to our strict standards and site is spotless. If you have any questions, please give me a call. We always want to provide the best value to our clients. If we are outside your budget, please let me know and we will do our best to work within that. Kind regards, Eric Teall | Project Estimator erict@callamnow.com 574-780-9474 CLASS 3 IMPACT RESISTANCE RATING3 HIGH-WIND RESISTANCE Wind resistance and fast installation — nailed. IKO’s Dynasty line stands a cut above the industry for shingles that perform from installation to weathering homeowners’ toughest storms. These laminated performance shingles offer: •ArmourZone 1 ¼-inch reinforced nailing surface for unparalleled holding power. •Class 3 impact resistance rating3. •A wide range of enhanced color blends. •True Square Advantage sizing providing exactly 100 square feet of coverage in every three bundles, helping minimize waste and installation costs. •Resistance against blue-green algae streaks and discoloration. •FastLock® sealant, activated by the warmth of the sun to seal down and help protect against wind uplift. High-Performing Laminated Shingles for the Weather-Conscious Homeowner. When your customers want a roof that’s a step above the rest, Dynasty Performance shingles provide an upgraded experience in multiple ways. Dynasty shingles feature our ArmourZone® 1 1/4-inch reinforced nailing surface, offering roofers a wider margin compared to standard architectural shingles. This tear-resistant band also makes Dynasty shingles less susceptible to wind uplift and includes a high-wind warranty for coverage up to 130 mph. Plus, Dynasty shingles feature enhanced colors and a Class 3 impact resistance rating for upgraded defense against hail3 *. *This is not a guarantee of impact resistance against hail. Damage from hail is not covered under the limited warranty. See full details3. The IKO Difference With a legacy of craftsmanship that spans over 75 years, we know quality. That’s why contractors and their customers trust IKO to deliver beautiful, high-performing roofing systems that can withstand rigorous conditions — and continue protecting families for generations to come. IKO.COM/NA IKO ARMOURZONE® ENHANCED COLORS IKO.COM/NA Note: Product and color availability may vary by region. Products with Miami Dade NOA and FBC product approval listings are available. Meets Texas Department of Insurance requirements. Contact IKO for details. ¹Refer to the Limited Warranty at IKO. com for full terms, conditions, restrictions and application requirements. Shingles must be installed per application instructions and local building codes. 2“Lifetime” refers to the period from installation until the original Owner no longer owns the building. 3Impact rating is solely for potential insurance premium reductions and is not a performance guarantee, implied or express warranty of any kind. Hail damage is not covered under the Limited Warranty. IKO recommends Class 4 or 3 impact resistance rated Hip and Ridge capping shingles be installed with corresponding impact rated shingles (refer to FM Approvals for more details on the FM 4473 impact resistance testing standard). 4All values are approximate. 5Products are developed with reference to these standards. 6Blue granules may tend to fade with prolonged UV exposure. 7Matte Black roofs may show shading (lighter or darker in some locations), which is not considered a defect under the terms of our warranty. © Copyright 12/24 · MR9L326 Information is subject to change without notice. We assume no responsibility for errors or omissions in this literature. Find out more about our products now by talking to an IKO sales representative or contact us directly: 1-888-IKO-ROOF (1-888-456-7663). Or visit our website at: IKO.COM. BROWNSTONEGLACIER FROSTONE GREY CORNERSTONE/ WEATHERWOOD GRANITE BLACK SHADOW BROWN DRIFTSHAKESUMMIT GREY STANDARDS5ASTM D3462 ASTM D3018 ASTM D7158 — Class H ASTM D3161 — Class F ASTM E108/UL 790 — Class A FM 4473 — Class 33SPECIFICATIONS4Limited Warranty1 Limited Lifetime2 Dimensions (L x W) 40 7/8 in (1,038 mm) X 13 3/4 in (349 mm) Iron Clad Protection1 15 Years Exposure 5 7/8 in (149 mm) Limited Wind Warranty1 130 mph Coverage per Bundle 33 1/3 sq. ft. (3.1 sq. m) Limited Algae Resistance Warranty¹10 years (blue-green)Shingles per Square 60 SENTINEL SLATE AVAILABLE IN SELECT MARKETS MATTE BLACK7ATLANTIC BLUE6 MONACO RED EMERALD GREEN BISCAYNE Become an IKO ROOFPRO Member. Call 1-866-ROOFPRO or visit us online ikoroofproconnect.com IMPORTANT! For complete satisfaction, view full-size shingles and an actual roof installation before selecting a color. Online swatches, brochures, and our ROOFViewer® tool may not accurately reflect the shingle color or full color blend range, nor show the impact of sunlight. IKO.COM/NASEE IT ON A ROOF IKO CAMBRIDGE/DYNASTY IKO - Cambridge or Dynasty Architectural Shingle Roof Item Qty IKO Architectural (10/12)4 IKO Architectural (12/12)4 IKO Architectural (6/12)12 Roof Scope Package Item Qty IKO Iron Clad Protection Period Limited Warranty 15/20 ROOF PREPARATION (REMOVAL/TEAR OFF HAUL AWAY) Remove the existing shingles along with current roof system down to the decking 3 Sheets of Decking Replacement Included IKO StormShield Ice & Water SYNTHETIC UNDERLAYMENT Installed directly on the roof deck providing a secondary layer of protection from the elements, including rain, snow, and wind IKO ARMOUR STARTER™LEADING EDGE PLUS™ Long, narrow shingles installed along the edges of the roof creating a watertight seal at the edge of your roof. Their pre-applied properly-positioned adhesive helps prevent shingle uplift and blow-off INSTALL RIDGE VENT Covers the cost of time and labor of installation of ridge vent. 2" Drip Edge ADDITIONAL WORK SCOPE Item Qty 3-4" Pipe Boot - EA 2 COUNTER FLASHING Additional flashing installed over top of areas where the roof meets a masonry wall 8 Remove Antenna 1 Quote subtotal $11,786.36 Cash/Check/9.9% Financing ($0.00) Discount ($0.00) Total $11,786.36 SF3060 (0% for 60 months) est. $196.83/mo AUTHORIZATION PAGE IKO Cambridge/Dynasty $11,786.36 Name:Mike Gerenscer Address:629 Portage Avenue, South Bend, IN, US, 46616-1356 Estimates are valid for 14 days. A 30% deposit or proof of financing must be received before a project can be scheduled. Final Price $11,786.36 Customer Comments / Notes My Product Selections IKO Series Shingle Color Drip Edge Color Mike Gerenscer:Date: 8/19/2026 LIMITED WARRANTIES IRON CLAD EXTENDED PROTECTION What You Get When You Choose an IKO ROOFPRO * Your roof should endure the elements to protect not only your family and your home, but everything you hold dear. With a roof installed by an IKO ROOFPRO Select or Craftsman Premier Contractor, you are eligible for an extended Iron Clad Protection Period Limited Warranty, giving you even more peace of mind. Compare the ROOFPRO Iron Clad Extended Protection Limited Warranty and the CodePlus™ Iron Clad Extended Protection Limited Warranty to our standard shingle limited warranty and see how they stack up. STANDARD WARRANTY IRON CLAD EXTENDED PROTECTION IN THE U.S. ROOFPRO Select and Craftsman Premier Shingle Products Architectural Shingles Performance Shingles Designer Shingles CodePlus2 Cambridge® & Cambridge® Cool Colors™ Dynasty® & Nordic™ Crowne Slate™, Royal Estate™ & Armourshake™ Dynasty & Nordic Installation Requirements See below for high wind requirements. Four-nailed, except five-nailed for Crowne Slate & Armourshake, IKO Hip & Ridge 12™, Hip & Ridge™ Class 4, IKO UltraHP®, IKO UltraHP® IR Four-nailed, Proformax™ Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Four-nailed, Proformax Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Four-nailed (Royal Estate), Five-nailed (Crowne Slate & Armourshake) Proformax Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Six-nailed, Proformax Accessories3, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Enhanced installation requirements apply. Iron Clad Protection Period (ICP) 10 years Cambridge & Cambridge Cool Colors 15 years Dynasty, Nordic, Crowne Slate, Armourshake & Royal Estate 15 years Cambridge & Cambridge Cool Colors 20 years 20 years 25 years Wind Warranty High Wind Warranty 4 110/130 mph Cambridge, Cambridge Cool Colors, Crowne Slate, Armourshake & Royal Estate 130 mph Dynasty & Nordic (Four-nailed) 110 mph (Four-nailed) 130 mph (Six-nailed) 130 mph (Four-nailed) 110 mph (Four-nailed, except five-nailed for Crowne Slate & Armourshake) 130 mph (Six-nailed, except eight-nailed for Crowne Slate) 130 mph (Six-nailed) Algae Resistance Warranty 10 years Cambridge Cool Colors Dual Grey only, 10 years 10 years** Cambridge & Cambridge Cool Colors Dual Grey** 10 years**10 years**10 years** Transferability Once during first 10 years only; coverage continues for a maximum of 10 years from installation. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Application Processing Fee $0 $0 $75 $75 $75 Reasonable Tear-Off and Disposal During the ICP Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above * IKO ROOFPRO is IKO’s contractor loyalty program. Membership in the program requires payment of annual membership fees to IKO and a commitment to purchase IKO products. The program provides its members access to valuable benefits, including rebates and rewards based on purchase volume, discounts or preferred rates with third-party providers and the ability to offer the Extended Iron Clad Protection limited warranties. For further information on the Program, please go to www.IKO.com/na, email IKOROOFPRO@IKO.com or call toll-free 1-866-ROOFPRØ (1-866-766-3770). Note: ROOFPRO Extended Limited Warranty can only be offered on roofs installed by an IKO ROOFPRO Select or Craftsman Premier Contractor. See Extended Limited Warranties for complete terms, conditions, restrictions and application requirements. Shingles must be applied in accordance with application instructions and local building code requirements; and for CodePlus, in accordance with the CodePlus Application Manual and local building requirements. The contractor is not a subcontractor, an agent, or a representative of IKO. IKO does not warrant or guarantee or make any representation regarding the workmanship or performance of this or any other contractor, nor provide any warranty or guarantee or assume any liability in respect to the CodePlus Application Method. The limited warranties, including the CodePlus Extended Limited Warranty, do not provide coverage in the event of improper installation by the contractor. ** Same as standard warranty. 1At least three qualifying Proformax Roofing Accessories are required. 2 CodePlus Extended Iron Clad Protection Limited Warranty can only be provided by an IKO ROOFPRO Select or Craftsman Premier Roofing Contractor who has met the requirements to install. 3For the Hybrid and Full-Coverage Ice & Water application methods (options 1 and 2 in section 2.2.1 of the CodePlus Application Manual), Nordic or Dynasty Shingles must be used and installed together with all five of the Proformax Integrated Roofing Accessories, items a., b., c., d. (ii.) and e. on the reverse. For the Warm Weather application method (see section 2.2.2 in the CodePlus Application Manual), intended for markets where Ice & Water is not required by building code, Nordic or Dynasty Shingles in conjunction with four Proformax Accessories are required, items b., c., d. (ii.) and e. on the reverse. Review all applicable building codes, minimum property standards and requirements before applying these products. 4High wind application requirements apply. 1. IKO Shingles must be used and installed together with at least three of the following IKO Proformax Integrated Roofing Accessories: Note: An IKO-approved Hip and Ridge cap shingle product is required. For CodePlus Extended Iron Clad Protection: For the Hybrid and Full-Coverage Ice & Water application methods (options 1 and 2 in section 2.2.1 of the CodePlus Application Manual), five Proformax Integrated Roofing Accessories are required, items a., b., c., d. (ii.) and e. below. For the Warm Weather application method (see section 2.2.2 in the CodePlus Application Manual), intended for markets where Ice & Water is not required by building code, four Proformax Accessories are required, items b., c., d. (ii.) and e. below. Review all applicable building codes, minimum property standards and requirements before applying these products. a. The use of IKO’s GoldShield™ Premium Ice & Water Protector, ArmourGard™ Ice & Water Protector or StormShield™ Ice & Water Protector membrane for sealing eaves and valleys. b. The use of an approved IKO synthetic underlayment under all shingle installations, such as Stormtite® or RoofGard-Cool Grey™. c. Required: Installation of any IKO-approved Hip and Ridge cap shingle product, which includes IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP or IKO UltraHP IR shingles. IKO recommends the use of its Class 4 impact resistance-rated Hip and Ridge cap shingle in conjunction with the use of Class 4 impact resistance-rated shingles, and the use of no less than its Class 3 impact resistance-rated Hip and Ridge cap shingle in conjunction with the use of Class 3 impact resistance-rated shingles. d. (i.) For IKO ROOFPRO Extended Iron Clad Protection: For Nordic and Dynasty, the application of IKO’s Leading Edge Plus™ starter strip installed at the eaves. For Crowne Slate, Royal Estate, Cambridge and Cambridge Cool Colors, the application of IKO’s Leading Edge Plus starter strip installed at the eaves and rakes. For Armourshake, the application of Leading Edge Plus with Armour Starter™ at the eaves. Alternatively, IKO EdgeSeal® can be used as the starter for all laminated shingles. (ii.) For CodePlus Extended Iron Clad Protection: How to submit warranty application. In order to obtain the IKO ROOFPRO Extended Iron Clad Protection or the CodePlus Extended Iron Clad Protection, your IKO ROOFPRO Contractor must submit an application for the extended limited warranty online at WWW.IKOROOFPRO.COM or by mail with a copy of the proof of purchase listing all the IKO products required for the roof system, along with the applicable nonrefundable application fee (the “Fee”). The extended limited warranty application and Fee must be received within 90 days after completion of the installation. The extended limited warranty is not effective until the homeowner receives written confirmation of approval from the IKO warranty program coordinator, whereupon the effective date shall be the date of completion of the installation. Application of IKO EdgeSeal self-adhering starter at the eaves and rakes. e. For CodePlus Extended Iron Clad Protection only: Application of IKO GoldSeam™ sealing tape. 2. The Shingles must be installed in strict accordance with the instructions on the wrapper; and for the CodePlus Extended Iron Clad Protection, in strict accordance with the instructions contained in the CodePlus Application Manual in effect at the time of the installation. 3. Valid only on complete single-family dwelling residential roofing applications with a minimum roof area of 10 squares, a maximum roof area of 100 squares and a roof pitch of 4:12 or steeper. CodePlus Extended Iron Clad Protection is available for roof pitches between 3:12 and 4:12 if enhanced installation requirements set out in the CodePlus Application Manual are met. 4. The attic is properly vented according to the highest of either ARMA, IKO or local building code requirements. A properly balanced ventilation system requires ridge, static vents and under-eave or soffit ventilation, and per ARMA’s requirements, the vents shall be uniformly distributed on opposite sides of the building in such a way that approximately 50% are near the lower part of the roof (inflow), and approximately 50% are near the ridge (outflow). 5. Installation on a clean, dry and stable roof deck without any of the previous shingles or roofing materials remaining on the roof. (Note: Installation of shingles directly over an existing layer will void the IKO ROOFPRO Extended Iron Clad Protection and the CodePlus Extended Iron Clad Protection.) 6. The roof must be installed by an IKO ROOFPRO Select or Craftsman Premier Contractor. For CodePlus Extended Iron Clad Protection to apply, the contractor must additionally meet the training and application requirements, and install the roof in accordance with the instructions set out in the CodePlus Application Manual. ROOFPRO Select or Craftsman Premier Contractors who have met this requirement will be so designated on the Find a Contractor lookup at www.IKO.com/na. 7. This warranty cannot be used in conjunction with a warranty claim settlement. In order to be eligible for the IKO ROOFPRO Extended Iron Clad Protection or the CodePlus Extended Iron Clad Protection, your roof must meet the following requirements: IKO Industries, Inc. 235 West South Tech Drive Kankakee, IL 60901-8426 The information in this literature is subject to change without notice. We assume no responsibility for errors that may appear in this literature. © 2023 IKO Industries Ltd. and IKO Industries, Inc. IKO ROOFPRO and the IKO (logo) are registered trademarks of IKO Industries Ltd. or IKO Industries Inc. All rights reserved. 03/23 MR8L136 IMPORTANT INFORMATION ABOUT YOUR IKO ROOFPRO WARRANTY I acknowledge that I have read and understand this page. Initials:MG TERMS AND CONDITIONS SAFETY A&M takes pride in providing a safe work environment for its employees and customers. Please refrain from climbing on ladders, scaffolding and your roof during the time A&M employees are working. This will allow for everyone to have a safe work environment during tear off and installation of your new roof, siding, soffit, fascia, or gutters. SECURITY SYSTEMS A&M is not responsible for security systems or alarms. It is the responsibility of the homeowner to disconnect the system prior to A&M performing any work on their home. A&M will not be responsible for security systems or alarms that may go off during the course of our work. EXISTING STRUCTURAL CONDITIONS A&M is not responsible for any existing structural problems, loose or cracked plaster, sags in rafters, bowed out walls. EXCESS MATERIALS Our proposals are based on a complete job. Any excess materials remain the property of A&M. LIGHT FIXTURES, PICTURES, and MIRRORS These items could fall and break due to the vibration of the work being done. We suggest that you check all fixtures, pictures, mirrors, etc. to make sure they are secure. If in doubt, take them down. We will not assume responsibility for these items as a result of the normal vibrations of home improvement work. ACCESS We plan to utilize driveways and walkways where they provide the necessary access to your home. If there is not sufficient access, we will put plywood down before driving on your lawn. We will not be responsible for any damage that occurs to the concrete or asphalt during this process. Please notify us in writing, five days prior to the job starting if you have a sprinkler system, septic field, a well or if you do not want us to use your driveway for our services. SCHEDULING Your material will be delivered by third party distribution. The office will contact you one day before your job is to begin. If there is no answer, we will leave a message. Please be advised that scheduling conflicts can occur due to circumstances beyond our control. SCHEDULING MULTIPLE PROJECTS If more than one project is being completed at your home, please be advised that there will be a brief period of time between each installation. Each project will also be invoiced separately. We appreciate your cooperation and patience during this process. Please ask your salesperson to explain this procedure in more detail if necessary. PAYMENT A&M will invoice you separately for the different types of work that are completed. Each of these invoices will be due as stated in each contract. Please ask your Sales Rep to explain this procedure more in detail. Your balance is due based on contract fulfillment. Warranty work and service request are outside the scope of the contract and will be serviced upon payment in full. A&M cannot cover the cost of deductibles from insurance companies. If declined for financing, we will require a 75% down payment in order to begin the work. RETAINAGE A&M will request 90% of the funds when job is substantially complete, to be paid either via cash, check, credit card, or by activating and approving financing. 10% should be the remaining balance to be kept by customer as good faith that the project will be completed in a timely manner once materials needed for completion are available. HOMEOWNERS ASSOCIATION / PROPERTY OWNERS ASSOCIATION It is the responsibility of the homeowner to notify A&M of any specific rules, colors or specifications that pertain to their list of covenants. CANCELLATIONS OF CONTRACT Customers have three business days from the date of contract signing to rescind their contract without penalty. If a customer chooses to cancel their contract after that time, they will incur a processing fee equal to 25% of their contract price plus the cost of any custom product. When applicable, these fees will be deducted directly from the customer’s down payment, otherwise the customer will be billed for these fees. FINAL PAYMENTS It is the sole responsibility of the customer to arrange payments from their insurance or mortgage companies. All invoices will be due as stated per the contract. I acknowledge that I have read and understand this page. Initials:MG SPECIFICS PERTAINING EXTERIOR PROJECTS: I understand that if roof rot is discovered during tear-off A&M reserves the right to replace sheathing and bill me up to $500 to the estimated cost below without notifying me in advance and will call me for authorization if wood replacement exceeds $500. Currently wood replacement is $85.00-$125.00 per 4'x8' sheet of OSB. Wood Fascia Replacement is $10.00 a Linear ft. [ M G ] ROOF WARRANTIES: A Golden Pledge Warranty, by GAF was offered. ME ID 25290 SKYLIGHTS A&M strongly recommends the replacement of skylights with the replacement of a new roof. If at the request of the customer the existing skylight(s) are not to be replaced with the roof, A&M cannot be held responsible for leaking after the installation or damage to the existing skylight(s) during the installation. [ M G ] AWNINGS, GRILLS, LAWN FURNITURE, AND ANY OTHER EXTERIOR FIXTURES These items should be removed, protected, rolled up, etc. by the homeowner before our crew arrive to start any exterior home improvement work. TREES AND BUSHES, If you have low hanging branches over your roof or against your siding, some trimming will be necessary. Homeowner will be responsible for cutting back any branches that limit A&M’s ability to do an efficient workmanlike job. Trees and bushes must be cut back prior to scheduling the start of your project. TEAR OFFS When it is necessary to remove your existing roof, some debris and/or asphalt may fall through the sheeting boards into your attic or garage. We suggest covering or removing items which require protection. A&M will not be responsible for any interior cleaning up. Nails will be used to install the shingles on your roof. These nails will protrude through the roof deck and be visible in the attic. WOOD REPLACEMENT A&M is not responsible for any moldy or damaged wood, which is visible from the interior of the building only. Homeowners should notify us, in writing, prior to the start of their job, should they wish to have us replace this type of decking. Any wood that is replaced by A&M will not be primed or painted unless otherwise stated. Any rafter work performed by A&M will be sistered onto existing rafters for additional support unless otherwise noted. PLYWOOD DECK If it becomes evident, once your existing roof has been removed, that the plywood deck was installed without proper spacing, A&M, will make the necessary repairs to the existing roof deck to ensure that the plywood underlayment is properly spaced. This may result in an extra charge at an hourly rate of $85 per hour. HIDDEN LINES A&M is not responsible for air conditioning lines, electrical wiring or conduit, plumbing pipes, cable or antenna wires that are mounted to the interior rafters, studs, decking or siding. It is the responsibility of the homeowner to inform A&M of any of these conditions prior to the start of the job. PLUMBING VENT PIPES Over time, cast iron pipes can rust and may need to be replaced by a plumber when pipe flashings are removed and replaced. In addition, built up corrosion on the inside of the pipe can become dislodged, due to the vibration that occurs during the tear off process. Should this be the case, A&M will not be responsible for the additional charges or for any damage that may occur if the pipe falls from its original position. MULTIPLE LAYERS A&M will not be responsible for stains and gaps that become visible along your siding walls after multiple layers are removed, and only one layer is installed. If you have questions, please ask your salesman. DISCOLORATION Airborne pollutants can cause staining or discoloration to appear on your gutters and other exterior products on your home. This discoloration or staining can be seen especially when light-colored products are installed. Neither A&M nor their manufacturers are responsible for stains or discoloration on your new gutters or other exterior products because of environmental factors, which are beyond their control. VENTILATION If not contracting with A&M for these services, it is the responsibility of the homeowner to ensure that their attic is insulated properly, and that the insulation is not restricting intake ventilation from eave vents. It is also the responsibility of the homeowner to make sure that all exhaust vents (i.e. dryers, range hoods, bathroom vents, etc.) are properly ventilating to the exterior of the home. A&M is not responsible for moisture buildup, condensation, installation of soffit vents, mold or mildew growth in your home relating to improper or insufficient air intake and insulation. If it is discovered that cathedral areas of your roof do not contain baffles which facilitate proper air flow A&M will need to install at $4.00 per baffle. If boards need to be removed and replaced to install baffles, the charge will be $3.00 per foot. Plywood will be removed to determine if baffles are present. If the existing plywood is found to be in good condition, those sheets will be reinstalled. The price to REMOVE AND REINSTALL Plywood is $35 per sheet. If the existing plywood is found to be rotten or cracked and needs to be replaced with NEW plywood, the plywood price on the first page of the contract will be charged. BROAN VENTS When applicable, A&M will install new broan vent(s) into existing locations or cut in additional broan vents and connect to existing bath fans with a flex hose. This will allow for the warm, humid air to escape out the roof instead of into the attic space. A&M is NOT responsible for broan vents or bath fans that come dislodged after the initial installation, nor re-connecting broan vents at a future date. It’s the responsibility of the customer to ensure the vents are properly secured and fastened to exhaust pipes. I acknowledge that I have read and understand this page. Initials:MG ICE DAMMING Ice damming occurs when gutters and downspouts freeze. Melting snow has nowhere to go, so water gets between shingles, which can cause leaks. This is not a problem related to the roofing workmanship. This problem is out of our control. A&M will not be responsible for leaks that occur because of ice damming. SEEPAGE AND WATER IN BASEMENTS A&M is not responsible for any seepage or water leakage in basements, which may occur in the absence of gutters and downspouts. If not written and specified on the contract where the downspouts should go, they will be installed back at the original location. ANTENNAS, please notify the office before work begins if you want your antenna removed. We will remove and/or dispose of antennas. We will not install new antennas. A&M will not be responsible for antenna reception. SATELLITE DISHES A&M will lift your satellite dish and will reset it where it is currently located and will ensure proper flashing of the dish. However, A&M is not responsible for any damage caused to the dish during this process or responsible for the reception of the dish. No exceptions will be made. If you prefer, you may contact your Satellite provider and have them remove the dish prior to the start of the job and reinstall it upon completion of the job. GUTTER REMOVAL AND REINSTALL If A&M is replacing fascia and soffit, but not existing gutters, and wood fascia boards need to be replaced we will charge $75.00 per every 50’ of gutters that need to be removed and reinstalled. This price does not include wood charges that are stated in the contract. GUTTER GUARDS If you have existing gutter guards and A&M needs to remove and replace them to complete your project. A&M cannot be responsible for minor damage due to this process. If you would prefer to remove them yourself prior to the installation, please have this done no later than one week from the date of your contract signing. SPECIFICS PERTAINING TO WINDOW AND DOOR PROJECTS: WINDOW TREATMENTS It is the responsibility of the homeowner to remove and later reinstall any and all window treatments prior to the start of your job. A&M will not be responsible for shades, blinds, or window treatments of any kind if not removed prior to job start. When installing replacement windows there is the possibility that your existing blinds/window treatments may no longer fit in the opening. M&M cannot be responsible for this. Please see the measure technician for further explanation, if necessary. FURNITURE & APPLIANCES It is the responsibility of the homeowner to remove all furniture and appliances a minimum of three feet away from all windows and doors to allow access for installation. A&M is not responsible for damage caused to furniture or appliances that are not moved prior to the start of your job. CAULKING is considered routine maintenance and therefore it is the responsibility of the homeowner. WOOD REPLACEMENT Unless previously agreed upon, any weak or rotten wood which is visible to our crew during the window/door installation will be replaced as necessary. The additional cost for the customer will be as follows: $4.85 per foot for all 1x4, 1x6 and 1x8 replacement and $10.50 per foot for any 2x4, 2x6 and 2x8 replacement. Any wood that is replaced by A&M will not be primed or painted unless otherwise stated. HAND STAINING As is the nature of hand-applied stains on wood, colors and grain patterns may vary slightly on all windows, wood trim and other wood products. CONDENSATION A&M is not responsible for conditions beyond its control, including condensation. Condensation is the result of excess humidity in your home. GLASS SPACE The glass space in your custom vinyl replacement windows could be slightly less than your existing windows. This is due to the construction of the window and is not a result of mismeasuring. LIFETIME LABOR WARRANTY Only applies to windows and sliding patio doors that have a manufacturing defect. If damage or defect is a result of an accident in the home, vandalism, or an act of God there will be a labor fee associated with the warranty. I acknowledge that I have read and understand this page. Initials:MG SPECIFICS PERTAINING INSULATION PROJECTS: CONDENSATION A&M is not responsible for conditions beyond its control, including condensation. Condensation is the result of excess humidity in your home. EXTERIOR VENTILATION A&M is not responsible for pre-existing conditions in your attic space including but not limited to the presence of mold & mildew. As manufactured, fiberglass insulation is resistant to mold growth. However, mold growth can occur on building materials, including insulation when it becomes contaminated with organic material and when water is present. A&M is not responsible for mold or mildew formation in your attic space for any reason. HVAC A&M is not responsible for pre-existing damage or deficiencies with your HVAC system. ELECTRIC USAGE A&M will need to use your electricity for the powering of the insulation machine. ATTIC ACCESS It is the responsibility of the customer to clear a path to allow access to your attic. If your attic access is in a closet, all shelving, clothing and contents must be removed by the homeowner prior to the installation. ATTIC CONTENTS It is the responsibility of the customer to remove all attic contents prior to the installation of your insulation. If you fail to remove attic contents, A&M will not be responsible for any damage to these items. EXHAUST VENTS A&M is not responsible for venting stove/range exhaust hoods, bathroom exhaust fans and dryer ventilation. These vents must be ventilated to the exterior of the home and are the responsibility of the customer to ensure that they are properly ventilated. VENTILATION If any of the requirements of intake and exhaust ventilation are not contracted with A&M, we will not be responsible for condensation, mold and mildew formation, or for any improper functioning of your attic insulation or ventilation. PAINTING It will be the responsibility of the homeowner to paint any added soffit vents cut into your existing wood soffit. COMPRESSION / SETTLING A&M is not responsible for settling your new insulation when installed over any type of existing insulation. SPECIFICS PERTAINING TO REPAIR PROJECTS: COLORING The color of all products installed for Repair Work may vary from the original products due to age, fading, discoloration of product, etc. WARRANTY Repair projects do not include a labor warranty, unless otherwise specified on the contract. THERE WILL BE SOME VIBRATION DUE TO THE SHINGLING ROOF, RE-SIDING, OR INSTALLATION OF WINDOWS OR DOORS ON YOUR HOME. A&M AND OUR SUPPLIERS CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE DUE TO THIS NORMAL VIBRATION, SUCH AS NAIL POPS, HAIRLINE CRACKS, LOOSENED FIXTURES, ETC. I HAVE READ AND FULLY UNDERSTAND THE DISCLAIMER SHEET. Mike Gerenscer 2026/08/19 I consent to receive personalized marketing communications on my work, products, promotions & events from A&M (e-mail, SMS, MMS, and telephone calls), by using the contact details that I provided. I understand that I can opt out at any time by emailing accounts@callamnow.com. FINAL AUTHORIZATION SUMMARY Status: Signed Agreement Completed: Wed, 19 Aug 2026 21:08:30 GMT • Document emailed for signature: Wed, 19 Aug 2026 19:51:34 GMT Document e-signed by: Mike Gerenscer (gerencserm@yahoo.com) Signature date: Wed, 19 Aug 2026 21:08:30 GMT IP address: 172.242.181.15 We can help you with Roofing, Waterproofing & Gutters Jared@callamnow.com (Sales Director) 574-855-1050 IKO ROOFING QUOTE AUG 13, 2026 MIKE GERENSCER 629 Portage Avenue, South Bend, IN, US, 46616-1356 INTRODUCTION Hi Mike , We recognize that safeguarding the people and possessions that hold the most value to you is of utmost importance. Your roof serves as the primary shield against the forces of nature, shielding your home from the elements and ensuring that everything inside remains safe and dry. Thank you for the opportunity to quote on the repairs and improvements to your home. Please find your estimate below along with upgrade options for potential improvements to your project, if applicable. The following estimate is for: 1. Remove and disposal of old materials 2. Supply and install new materials 3. Clean up of entire work area (all nails and other materials) 4. We are fully licensed to work in your location Once the job is complete, one of our Quality Control Officers from our Audit Division inspects your project to make sure we did everything correct and up to our strict standards and site is spotless. If you have any questions, please give me a call. We always want to provide the best value to our clients. If we are outside your budget, please let me know and we will do our best to work within that. Kind regards, Eric Teall | Project Estimator erict@callamnow.com 574-780-9474 CLASS 3 IMPACT RESISTANCE RATING3 HIGH-WIND RESISTANCE Wind resistance and fast installation — nailed. IKO’s Dynasty line stands a cut above the industry for shingles that perform from installation to weathering homeowners’ toughest storms. These laminated performance shingles offer: •ArmourZone 1 ¼-inch reinforced nailing surface for unparalleled holding power. •Class 3 impact resistance rating3. •A wide range of enhanced color blends. •True Square Advantage sizing providing exactly 100 square feet of coverage in every three bundles, helping minimize waste and installation costs. •Resistance against blue-green algae streaks and discoloration. •FastLock® sealant, activated by the warmth of the sun to seal down and help protect against wind uplift. High-Performing Laminated Shingles for the Weather-Conscious Homeowner. When your customers want a roof that’s a step above the rest, Dynasty Performance shingles provide an upgraded experience in multiple ways. Dynasty shingles feature our ArmourZone® 1 1/4-inch reinforced nailing surface, offering roofers a wider margin compared to standard architectural shingles. This tear-resistant band also makes Dynasty shingles less susceptible to wind uplift and includes a high-wind warranty for coverage up to 130 mph. Plus, Dynasty shingles feature enhanced colors and a Class 3 impact resistance rating for upgraded defense against hail3 *. *This is not a guarantee of impact resistance against hail. Damage from hail is not covered under the limited warranty. See full details3. The IKO Difference With a legacy of craftsmanship that spans over 75 years, we know quality. That’s why contractors and their customers trust IKO to deliver beautiful, high-performing roofing systems that can withstand rigorous conditions — and continue protecting families for generations to come. IKO.COM/NA IKO ARMOURZONE® ENHANCED COLORS IKO.COM/NA Note: Product and color availability may vary by region. Products with Miami Dade NOA and FBC product approval listings are available. Meets Texas Department of Insurance requirements. Contact IKO for details. ¹Refer to the Limited Warranty at IKO. com for full terms, conditions, restrictions and application requirements. Shingles must be installed per application instructions and local building codes. 2“Lifetime” refers to the period from installation until the original Owner no longer owns the building. 3Impact rating is solely for potential insurance premium reductions and is not a performance guarantee, implied or express warranty of any kind. Hail damage is not covered under the Limited Warranty. IKO recommends Class 4 or 3 impact resistance rated Hip and Ridge capping shingles be installed with corresponding impact rated shingles (refer to FM Approvals for more details on the FM 4473 impact resistance testing standard). 4All values are approximate. 5Products are developed with reference to these standards. 6Blue granules may tend to fade with prolonged UV exposure. 7Matte Black roofs may show shading (lighter or darker in some locations), which is not considered a defect under the terms of our warranty. © Copyright 12/24 · MR9L326 Information is subject to change without notice. We assume no responsibility for errors or omissions in this literature. Find out more about our products now by talking to an IKO sales representative or contact us directly: 1-888-IKO-ROOF (1-888-456-7663). Or visit our website at: IKO.COM. BROWNSTONEGLACIER FROSTONE GREY CORNERSTONE/ WEATHERWOOD GRANITE BLACK SHADOW BROWN DRIFTSHAKESUMMIT GREY STANDARDS5ASTM D3462 ASTM D3018 ASTM D7158 — Class H ASTM D3161 — Class F ASTM E108/UL 790 — Class A FM 4473 — Class 33SPECIFICATIONS4Limited Warranty1 Limited Lifetime2 Dimensions (L x W) 40 7/8 in (1,038 mm) X 13 3/4 in (349 mm) Iron Clad Protection1 15 Years Exposure 5 7/8 in (149 mm) Limited Wind Warranty1 130 mph Coverage per Bundle 33 1/3 sq. ft. (3.1 sq. m) Limited Algae Resistance Warranty¹10 years (blue-green)Shingles per Square 60 SENTINEL SLATE AVAILABLE IN SELECT MARKETS MATTE BLACK7ATLANTIC BLUE6 MONACO RED EMERALD GREEN BISCAYNE Become an IKO ROOFPRO Member. Call 1-866-ROOFPRO or visit us online ikoroofproconnect.com IMPORTANT! For complete satisfaction, view full-size shingles and an actual roof installation before selecting a color. Online swatches, brochures, and our ROOFViewer® tool may not accurately reflect the shingle color or full color blend range, nor show the impact of sunlight. IKO.COM/NASEE IT ON A ROOF IKO CAMBRIDGE/DYNASTY IKO - Cambridge or Dynasty Architectural Shingle Roof Item Qty IKO Architectural (10/12)4 IKO Architectural (12/12)4 IKO Architectural (6/12)12 Roof Scope Package Item Qty IKO Iron Clad Protection Period Limited Warranty 15/20 ROOF PREPARATION (REMOVAL/TEAR OFF HAUL AWAY) Remove the existing shingles along with current roof system down to the decking 3 Sheets of Decking Replacement Included IKO StormShield Ice & Water SYNTHETIC UNDERLAYMENT Installed directly on the roof deck providing a secondary layer of protection from the elements, including rain, snow, and wind IKO ARMOUR STARTER™LEADING EDGE PLUS™ Long, narrow shingles installed along the edges of the roof creating a watertight seal at the edge of your roof. Their pre-applied properly-positioned adhesive helps prevent shingle uplift and blow-off INSTALL RIDGE VENT Covers the cost of time and labor of installation of ridge vent. 2" Drip Edge ADDITIONAL WORK SCOPE Item Qty 3-4" Pipe Boot - EA 2 COUNTER FLASHING Additional flashing installed over top of areas where the roof meets a masonry wall 8 Remove Antenna 1 Quote subtotal $11,786.36 Cash/Check/9.9% Financing ($0.00) Discount ($0.00) Total $11,786.36 SF3060 (0% for 60 months) est. $196.83/mo AUTHORIZATION PAGE IKO Cambridge/Dynasty $11,786.36 Name:Mike Gerenscer Address:629 Portage Avenue, South Bend, IN, US, 46616-1356 Estimates are valid for 14 days. A 30% deposit or proof of financing must be received before a project can be scheduled. Final Price $11,786.36 Customer Comments / Notes My Product Selections IKO Series Shingle Color Drip Edge Color Mike Gerenscer:Date: 8/19/2026 LIMITED WARRANTIES IRON CLAD EXTENDED PROTECTION What You Get When You Choose an IKO ROOFPRO * Your roof should endure the elements to protect not only your family and your home, but everything you hold dear. With a roof installed by an IKO ROOFPRO Select or Craftsman Premier Contractor, you are eligible for an extended Iron Clad Protection Period Limited Warranty, giving you even more peace of mind. Compare the ROOFPRO Iron Clad Extended Protection Limited Warranty and the CodePlus™ Iron Clad Extended Protection Limited Warranty to our standard shingle limited warranty and see how they stack up. STANDARD WARRANTY IRON CLAD EXTENDED PROTECTION IN THE U.S. ROOFPRO Select and Craftsman Premier Shingle Products Architectural Shingles Performance Shingles Designer Shingles CodePlus2 Cambridge® & Cambridge® Cool Colors™ Dynasty® & Nordic™ Crowne Slate™, Royal Estate™ & Armourshake™ Dynasty & Nordic Installation Requirements See below for high wind requirements. Four-nailed, except five-nailed for Crowne Slate & Armourshake, IKO Hip & Ridge 12™, Hip & Ridge™ Class 4, IKO UltraHP®, IKO UltraHP® IR Four-nailed, Proformax™ Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Four-nailed, Proformax Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Four-nailed (Royal Estate), Five-nailed (Crowne Slate & Armourshake) Proformax Accessories1, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Six-nailed, Proformax Accessories3, IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP, IKO UltraHP IR Enhanced installation requirements apply. Iron Clad Protection Period (ICP) 10 years Cambridge & Cambridge Cool Colors 15 years Dynasty, Nordic, Crowne Slate, Armourshake & Royal Estate 15 years Cambridge & Cambridge Cool Colors 20 years 20 years 25 years Wind Warranty High Wind Warranty 4 110/130 mph Cambridge, Cambridge Cool Colors, Crowne Slate, Armourshake & Royal Estate 130 mph Dynasty & Nordic (Four-nailed) 110 mph (Four-nailed) 130 mph (Six-nailed) 130 mph (Four-nailed) 110 mph (Four-nailed, except five-nailed for Crowne Slate & Armourshake) 130 mph (Six-nailed, except eight-nailed for Crowne Slate) 130 mph (Six-nailed) Algae Resistance Warranty 10 years Cambridge Cool Colors Dual Grey only, 10 years 10 years** Cambridge & Cambridge Cool Colors Dual Grey** 10 years**10 years**10 years** Transferability Once during first 10 years only; coverage continues for a maximum of 10 years from installation. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Once during first 15 years; ICP remains until year 15 but w/o tear-off and disposal. If transfer after year 12, ICP terminates and prorated coverage until year 15. Application Processing Fee $0 $0 $75 $75 $75 Reasonable Tear-Off and Disposal During the ICP Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above Yes, limited upon transfer as set out above * IKO ROOFPRO is IKO’s contractor loyalty program. Membership in the program requires payment of annual membership fees to IKO and a commitment to purchase IKO products. The program provides its members access to valuable benefits, including rebates and rewards based on purchase volume, discounts or preferred rates with third-party providers and the ability to offer the Extended Iron Clad Protection limited warranties. For further information on the Program, please go to www.IKO.com/na, email IKOROOFPRO@IKO.com or call toll-free 1-866-ROOFPRØ (1-866-766-3770). Note: ROOFPRO Extended Limited Warranty can only be offered on roofs installed by an IKO ROOFPRO Select or Craftsman Premier Contractor. See Extended Limited Warranties for complete terms, conditions, restrictions and application requirements. Shingles must be applied in accordance with application instructions and local building code requirements; and for CodePlus, in accordance with the CodePlus Application Manual and local building requirements. The contractor is not a subcontractor, an agent, or a representative of IKO. IKO does not warrant or guarantee or make any representation regarding the workmanship or performance of this or any other contractor, nor provide any warranty or guarantee or assume any liability in respect to the CodePlus Application Method. The limited warranties, including the CodePlus Extended Limited Warranty, do not provide coverage in the event of improper installation by the contractor. ** Same as standard warranty. 1At least three qualifying Proformax Roofing Accessories are required. 2 CodePlus Extended Iron Clad Protection Limited Warranty can only be provided by an IKO ROOFPRO Select or Craftsman Premier Roofing Contractor who has met the requirements to install. 3For the Hybrid and Full-Coverage Ice & Water application methods (options 1 and 2 in section 2.2.1 of the CodePlus Application Manual), Nordic or Dynasty Shingles must be used and installed together with all five of the Proformax Integrated Roofing Accessories, items a., b., c., d. (ii.) and e. on the reverse. For the Warm Weather application method (see section 2.2.2 in the CodePlus Application Manual), intended for markets where Ice & Water is not required by building code, Nordic or Dynasty Shingles in conjunction with four Proformax Accessories are required, items b., c., d. (ii.) and e. on the reverse. Review all applicable building codes, minimum property standards and requirements before applying these products. 4High wind application requirements apply. 1. IKO Shingles must be used and installed together with at least three of the following IKO Proformax Integrated Roofing Accessories: Note: An IKO-approved Hip and Ridge cap shingle product is required. For CodePlus Extended Iron Clad Protection: For the Hybrid and Full-Coverage Ice & Water application methods (options 1 and 2 in section 2.2.1 of the CodePlus Application Manual), five Proformax Integrated Roofing Accessories are required, items a., b., c., d. (ii.) and e. below. For the Warm Weather application method (see section 2.2.2 in the CodePlus Application Manual), intended for markets where Ice & Water is not required by building code, four Proformax Accessories are required, items b., c., d. (ii.) and e. below. Review all applicable building codes, minimum property standards and requirements before applying these products. a. The use of IKO’s GoldShield™ Premium Ice & Water Protector, ArmourGard™ Ice & Water Protector or StormShield™ Ice & Water Protector membrane for sealing eaves and valleys. b. The use of an approved IKO synthetic underlayment under all shingle installations, such as Stormtite® or RoofGard-Cool Grey™. c. Required: Installation of any IKO-approved Hip and Ridge cap shingle product, which includes IKO Hip & Ridge 12, Hip & Ridge Class 4, IKO UltraHP or IKO UltraHP IR shingles. IKO recommends the use of its Class 4 impact resistance-rated Hip and Ridge cap shingle in conjunction with the use of Class 4 impact resistance-rated shingles, and the use of no less than its Class 3 impact resistance-rated Hip and Ridge cap shingle in conjunction with the use of Class 3 impact resistance-rated shingles. d. (i.) For IKO ROOFPRO Extended Iron Clad Protection: For Nordic and Dynasty, the application of IKO’s Leading Edge Plus™ starter strip installed at the eaves. For Crowne Slate, Royal Estate, Cambridge and Cambridge Cool Colors, the application of IKO’s Leading Edge Plus starter strip installed at the eaves and rakes. For Armourshake, the application of Leading Edge Plus with Armour Starter™ at the eaves. Alternatively, IKO EdgeSeal® can be used as the starter for all laminated shingles. (ii.) For CodePlus Extended Iron Clad Protection: How to submit warranty application. In order to obtain the IKO ROOFPRO Extended Iron Clad Protection or the CodePlus Extended Iron Clad Protection, your IKO ROOFPRO Contractor must submit an application for the extended limited warranty online at WWW.IKOROOFPRO.COM or by mail with a copy of the proof of purchase listing all the IKO products required for the roof system, along with the applicable nonrefundable application fee (the “Fee”). The extended limited warranty application and Fee must be received within 90 days after completion of the installation. The extended limited warranty is not effective until the homeowner receives written confirmation of approval from the IKO warranty program coordinator, whereupon the effective date shall be the date of completion of the installation. Application of IKO EdgeSeal self-adhering starter at the eaves and rakes. e. For CodePlus Extended Iron Clad Protection only: Application of IKO GoldSeam™ sealing tape. 2. The Shingles must be installed in strict accordance with the instructions on the wrapper; and for the CodePlus Extended Iron Clad Protection, in strict accordance with the instructions contained in the CodePlus Application Manual in effect at the time of the installation. 3. Valid only on complete single-family dwelling residential roofing applications with a minimum roof area of 10 squares, a maximum roof area of 100 squares and a roof pitch of 4:12 or steeper. CodePlus Extended Iron Clad Protection is available for roof pitches between 3:12 and 4:12 if enhanced installation requirements set out in the CodePlus Application Manual are met. 4. The attic is properly vented according to the highest of either ARMA, IKO or local building code requirements. A properly balanced ventilation system requires ridge, static vents and under-eave or soffit ventilation, and per ARMA’s requirements, the vents shall be uniformly distributed on opposite sides of the building in such a way that approximately 50% are near the lower part of the roof (inflow), and approximately 50% are near the ridge (outflow). 5. Installation on a clean, dry and stable roof deck without any of the previous shingles or roofing materials remaining on the roof. (Note: Installation of shingles directly over an existing layer will void the IKO ROOFPRO Extended Iron Clad Protection and the CodePlus Extended Iron Clad Protection.) 6. The roof must be installed by an IKO ROOFPRO Select or Craftsman Premier Contractor. For CodePlus Extended Iron Clad Protection to apply, the contractor must additionally meet the training and application requirements, and install the roof in accordance with the instructions set out in the CodePlus Application Manual. ROOFPRO Select or Craftsman Premier Contractors who have met this requirement will be so designated on the Find a Contractor lookup at www.IKO.com/na. 7. This warranty cannot be used in conjunction with a warranty claim settlement. In order to be eligible for the IKO ROOFPRO Extended Iron Clad Protection or the CodePlus Extended Iron Clad Protection, your roof must meet the following requirements: IKO Industries, Inc. 235 West South Tech Drive Kankakee, IL 60901-8426 The information in this literature is subject to change without notice. We assume no responsibility for errors that may appear in this literature. © 2023 IKO Industries Ltd. and IKO Industries, Inc. IKO ROOFPRO and the IKO (logo) are registered trademarks of IKO Industries Ltd. or IKO Industries Inc. All rights reserved. 03/23 MR8L136 IMPORTANT INFORMATION ABOUT YOUR IKO ROOFPRO WARRANTY I acknowledge that I have read and understand this page. Initials:MG TERMS AND CONDITIONS SAFETY A&M takes pride in providing a safe work environment for its employees and customers. Please refrain from climbing on ladders, scaffolding and your roof during the time A&M employees are working. This will allow for everyone to have a safe work environment during tear off and installation of your new roof, siding, soffit, fascia, or gutters. SECURITY SYSTEMS A&M is not responsible for security systems or alarms. It is the responsibility of the homeowner to disconnect the system prior to A&M performing any work on their home. A&M will not be responsible for security systems or alarms that may go off during the course of our work. EXISTING STRUCTURAL CONDITIONS A&M is not responsible for any existing structural problems, loose or cracked plaster, sags in rafters, bowed out walls. EXCESS MATERIALS Our proposals are based on a complete job. Any excess materials remain the property of A&M. LIGHT FIXTURES, PICTURES, and MIRRORS These items could fall and break due to the vibration of the work being done. We suggest that you check all fixtures, pictures, mirrors, etc. to make sure they are secure. If in doubt, take them down. We will not assume responsibility for these items as a result of the normal vibrations of home improvement work. ACCESS We plan to utilize driveways and walkways where they provide the necessary access to your home. If there is not sufficient access, we will put plywood down before driving on your lawn. We will not be responsible for any damage that occurs to the concrete or asphalt during this process. Please notify us in writing, five days prior to the job starting if you have a sprinkler system, septic field, a well or if you do not want us to use your driveway for our services. SCHEDULING Your material will be delivered by third party distribution. The office will contact you one day before your job is to begin. If there is no answer, we will leave a message. Please be advised that scheduling conflicts can occur due to circumstances beyond our control. SCHEDULING MULTIPLE PROJECTS If more than one project is being completed at your home, please be advised that there will be a brief period of time between each installation. Each project will also be invoiced separately. We appreciate your cooperation and patience during this process. Please ask your salesperson to explain this procedure in more detail if necessary. PAYMENT A&M will invoice you separately for the different types of work that are completed. Each of these invoices will be due as stated in each contract. Please ask your Sales Rep to explain this procedure more in detail. Your balance is due based on contract fulfillment. Warranty work and service request are outside the scope of the contract and will be serviced upon payment in full. A&M cannot cover the cost of deductibles from insurance companies. If declined for financing, we will require a 75% down payment in order to begin the work. RETAINAGE A&M will request 90% of the funds when job is substantially complete, to be paid either via cash, check, credit card, or by activating and approving financing. 10% should be the remaining balance to be kept by customer as good faith that the project will be completed in a timely manner once materials needed for completion are available. HOMEOWNERS ASSOCIATION / PROPERTY OWNERS ASSOCIATION It is the responsibility of the homeowner to notify A&M of any specific rules, colors or specifications that pertain to their list of covenants. CANCELLATIONS OF CONTRACT Customers have three business days from the date of contract signing to rescind their contract without penalty. If a customer chooses to cancel their contract after that time, they will incur a processing fee equal to 25% of their contract price plus the cost of any custom product. When applicable, these fees will be deducted directly from the customer’s down payment, otherwise the customer will be billed for these fees. FINAL PAYMENTS It is the sole responsibility of the customer to arrange payments from their insurance or mortgage companies. All invoices will be due as stated per the contract. I acknowledge that I have read and understand this page. Initials:MG SPECIFICS PERTAINING EXTERIOR PROJECTS: I understand that if roof rot is discovered during tear-off A&M reserves the right to replace sheathing and bill me up to $500 to the estimated cost below without notifying me in advance and will call me for authorization if wood replacement exceeds $500. Currently wood replacement is $85.00-$125.00 per 4'x8' sheet of OSB. Wood Fascia Replacement is $10.00 a Linear ft. [ M G ] ROOF WARRANTIES: A Golden Pledge Warranty, by GAF was offered. ME ID 25290 SKYLIGHTS A&M strongly recommends the replacement of skylights with the replacement of a new roof. If at the request of the customer the existing skylight(s) are not to be replaced with the roof, A&M cannot be held responsible for leaking after the installation or damage to the existing skylight(s) during the installation. [ M G ] AWNINGS, GRILLS, LAWN FURNITURE, AND ANY OTHER EXTERIOR FIXTURES These items should be removed, protected, rolled up, etc. by the homeowner before our crew arrive to start any exterior home improvement work. TREES AND BUSHES, If you have low hanging branches over your roof or against your siding, some trimming will be necessary. Homeowner will be responsible for cutting back any branches that limit A&M’s ability to do an efficient workmanlike job. Trees and bushes must be cut back prior to scheduling the start of your project. TEAR OFFS When it is necessary to remove your existing roof, some debris and/or asphalt may fall through the sheeting boards into your attic or garage. We suggest covering or removing items which require protection. A&M will not be responsible for any interior cleaning up. Nails will be used to install the shingles on your roof. These nails will protrude through the roof deck and be visible in the attic. WOOD REPLACEMENT A&M is not responsible for any moldy or damaged wood, which is visible from the interior of the building only. Homeowners should notify us, in writing, prior to the start of their job, should they wish to have us replace this type of decking. Any wood that is replaced by A&M will not be primed or painted unless otherwise stated. Any rafter work performed by A&M will be sistered onto existing rafters for additional support unless otherwise noted. PLYWOOD DECK If it becomes evident, once your existing roof has been removed, that the plywood deck was installed without proper spacing, A&M, will make the necessary repairs to the existing roof deck to ensure that the plywood underlayment is properly spaced. This may result in an extra charge at an hourly rate of $85 per hour. HIDDEN LINES A&M is not responsible for air conditioning lines, electrical wiring or conduit, plumbing pipes, cable or antenna wires that are mounted to the interior rafters, studs, decking or siding. It is the responsibility of the homeowner to inform A&M of any of these conditions prior to the start of the job. PLUMBING VENT PIPES Over time, cast iron pipes can rust and may need to be replaced by a plumber when pipe flashings are removed and replaced. In addition, built up corrosion on the inside of the pipe can become dislodged, due to the vibration that occurs during the tear off process. Should this be the case, A&M will not be responsible for the additional charges or for any damage that may occur if the pipe falls from its original position. MULTIPLE LAYERS A&M will not be responsible for stains and gaps that become visible along your siding walls after multiple layers are removed, and only one layer is installed. If you have questions, please ask your salesman. DISCOLORATION Airborne pollutants can cause staining or discoloration to appear on your gutters and other exterior products on your home. This discoloration or staining can be seen especially when light-colored products are installed. Neither A&M nor their manufacturers are responsible for stains or discoloration on your new gutters or other exterior products because of environmental factors, which are beyond their control. VENTILATION If not contracting with A&M for these services, it is the responsibility of the homeowner to ensure that their attic is insulated properly, and that the insulation is not restricting intake ventilation from eave vents. It is also the responsibility of the homeowner to make sure that all exhaust vents (i.e. dryers, range hoods, bathroom vents, etc.) are properly ventilating to the exterior of the home. A&M is not responsible for moisture buildup, condensation, installation of soffit vents, mold or mildew growth in your home relating to improper or insufficient air intake and insulation. If it is discovered that cathedral areas of your roof do not contain baffles which facilitate proper air flow A&M will need to install at $4.00 per baffle. If boards need to be removed and replaced to install baffles, the charge will be $3.00 per foot. Plywood will be removed to determine if baffles are present. If the existing plywood is found to be in good condition, those sheets will be reinstalled. The price to REMOVE AND REINSTALL Plywood is $35 per sheet. If the existing plywood is found to be rotten or cracked and needs to be replaced with NEW plywood, the plywood price on the first page of the contract will be charged. BROAN VENTS When applicable, A&M will install new broan vent(s) into existing locations or cut in additional broan vents and connect to existing bath fans with a flex hose. This will allow for the warm, humid air to escape out the roof instead of into the attic space. A&M is NOT responsible for broan vents or bath fans that come dislodged after the initial installation, nor re-connecting broan vents at a future date. It’s the responsibility of the customer to ensure the vents are properly secured and fastened to exhaust pipes. I acknowledge that I have read and understand this page. Initials:MG ICE DAMMING Ice damming occurs when gutters and downspouts freeze. Melting snow has nowhere to go, so water gets between shingles, which can cause leaks. This is not a problem related to the roofing workmanship. This problem is out of our control. A&M will not be responsible for leaks that occur because of ice damming. SEEPAGE AND WATER IN BASEMENTS A&M is not responsible for any seepage or water leakage in basements, which may occur in the absence of gutters and downspouts. If not written and specified on the contract where the downspouts should go, they will be installed back at the original location. ANTENNAS, please notify the office before work begins if you want your antenna removed. We will remove and/or dispose of antennas. We will not install new antennas. A&M will not be responsible for antenna reception. SATELLITE DISHES A&M will lift your satellite dish and will reset it where it is currently located and will ensure proper flashing of the dish. However, A&M is not responsible for any damage caused to the dish during this process or responsible for the reception of the dish. No exceptions will be made. If you prefer, you may contact your Satellite provider and have them remove the dish prior to the start of the job and reinstall it upon completion of the job. GUTTER REMOVAL AND REINSTALL If A&M is replacing fascia and soffit, but not existing gutters, and wood fascia boards need to be replaced we will charge $75.00 per every 50’ of gutters that need to be removed and reinstalled. This price does not include wood charges that are stated in the contract. GUTTER GUARDS If you have existing gutter guards and A&M needs to remove and replace them to complete your project. A&M cannot be responsible for minor damage due to this process. If you would prefer to remove them yourself prior to the installation, please have this done no later than one week from the date of your contract signing. SPECIFICS PERTAINING TO WINDOW AND DOOR PROJECTS: WINDOW TREATMENTS It is the responsibility of the homeowner to remove and later reinstall any and all window treatments prior to the start of your job. A&M will not be responsible for shades, blinds, or window treatments of any kind if not removed prior to job start. When installing replacement windows there is the possibility that your existing blinds/window treatments may no longer fit in the opening. M&M cannot be responsible for this. Please see the measure technician for further explanation, if necessary. FURNITURE & APPLIANCES It is the responsibility of the homeowner to remove all furniture and appliances a minimum of three feet away from all windows and doors to allow access for installation. A&M is not responsible for damage caused to furniture or appliances that are not moved prior to the start of your job. CAULKING is considered routine maintenance and therefore it is the responsibility of the homeowner. WOOD REPLACEMENT Unless previously agreed upon, any weak or rotten wood which is visible to our crew during the window/door installation will be replaced as necessary. The additional cost for the customer will be as follows: $4.85 per foot for all 1x4, 1x6 and 1x8 replacement and $10.50 per foot for any 2x4, 2x6 and 2x8 replacement. Any wood that is replaced by A&M will not be primed or painted unless otherwise stated. HAND STAINING As is the nature of hand-applied stains on wood, colors and grain patterns may vary slightly on all windows, wood trim and other wood products. CONDENSATION A&M is not responsible for conditions beyond its control, including condensation. Condensation is the result of excess humidity in your home. GLASS SPACE The glass space in your custom vinyl replacement windows could be slightly less than your existing windows. This is due to the construction of the window and is not a result of mismeasuring. LIFETIME LABOR WARRANTY Only applies to windows and sliding patio doors that have a manufacturing defect. If damage or defect is a result of an accident in the home, vandalism, or an act of God there will be a labor fee associated with the warranty. I acknowledge that I have read and understand this page. Initials:MG SPECIFICS PERTAINING INSULATION PROJECTS: CONDENSATION A&M is not responsible for conditions beyond its control, including condensation. Condensation is the result of excess humidity in your home. EXTERIOR VENTILATION A&M is not responsible for pre-existing conditions in your attic space including but not limited to the presence of mold & mildew. As manufactured, fiberglass insulation is resistant to mold growth. However, mold growth can occur on building materials, including insulation when it becomes contaminated with organic material and when water is present. A&M is not responsible for mold or mildew formation in your attic space for any reason. HVAC A&M is not responsible for pre-existing damage or deficiencies with your HVAC system. ELECTRIC USAGE A&M will need to use your electricity for the powering of the insulation machine. ATTIC ACCESS It is the responsibility of the customer to clear a path to allow access to your attic. If your attic access is in a closet, all shelving, clothing and contents must be removed by the homeowner prior to the installation. ATTIC CONTENTS It is the responsibility of the customer to remove all attic contents prior to the installation of your insulation. If you fail to remove attic contents, A&M will not be responsible for any damage to these items. EXHAUST VENTS A&M is not responsible for venting stove/range exhaust hoods, bathroom exhaust fans and dryer ventilation. These vents must be ventilated to the exterior of the home and are the responsibility of the customer to ensure that they are properly ventilated. VENTILATION If any of the requirements of intake and exhaust ventilation are not contracted with A&M, we will not be responsible for condensation, mold and mildew formation, or for any improper functioning of your attic insulation or ventilation. PAINTING It will be the responsibility of the homeowner to paint any added soffit vents cut into your existing wood soffit. COMPRESSION / SETTLING A&M is not responsible for settling your new insulation when installed over any type of existing insulation. SPECIFICS PERTAINING TO REPAIR PROJECTS: COLORING The color of all products installed for Repair Work may vary from the original products due to age, fading, discoloration of product, etc. WARRANTY Repair projects do not include a labor warranty, unless otherwise specified on the contract. THERE WILL BE SOME VIBRATION DUE TO THE SHINGLING ROOF, RE-SIDING, OR INSTALLATION OF WINDOWS OR DOORS ON YOUR HOME. A&M AND OUR SUPPLIERS CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE DUE TO THIS NORMAL VIBRATION, SUCH AS NAIL POPS, HAIRLINE CRACKS, LOOSENED FIXTURES, ETC. I HAVE READ AND FULLY UNDERSTAND THE DISCLAIMER SHEET. Mike Gerenscer 2026/08/19 I consent to receive personalized marketing communications on my work, products, promotions & events from A&M (e-mail, SMS, MMS, and telephone calls), by using the contact details that I provided. I understand that I can opt out at any time by emailing accounts@callamnow.com. FINAL AUTHORIZATION SUMMARY Status: Signed Agreement Completed: Wed, 19 Aug 2026 21:08:30 GMT • Document emailed for signature: Wed, 19 Aug 2026 19:51:34 GMT Document e-signed by: Mike Gerenscer ( Signature date: Wed, 19 Aug 2026 21:08:30 GMT IP address: 172.242.181.15