The URL can be used to link to this page

Home My WebLink About304 South Twyckenham Drive_AA 2025-0709Sarah Andrews, President HISTORIC PRESERVATION COMMISSION OF SOUTH BEND AND ST. JOSEPH COUNTY CERTIFICATE OF APPROPRIATENESS The Historic Preservation Commission of South Bend and St. Joseph County has approved the following work: Removal of old EPDM rubber roofing and installation of new EPDM roofing with repairs as needed. Installation of half round gutter around the perimeter. Railing to be removed and reinstalled. Renew Roofing LLC, Contractor for the following location: 304 TWYCKENHAM DR South Bend, IN, 46615 East Wayne Street Application No. 2025-0709 in the County of St. Joseph; State of Indiana; which is: Located in a Local Historic District A Local Historic Landmark and found this application to be appropriate according to the Standards pertaining to Local Historic Landmarks and/or Local Historic Districts. Regulations pertaining to the Historic Preservation Commission are found in Chapter 21 (Zoning), South Bend Municipal Code and Chapter 26 of the St. Joseph County Code. The issuance of this certificate does NOT in any manner, release the recipient from the responsibility of complying with the requirements of the zoning ordinances, building codes, safety codes, ADA or other requirements of the City of South Bend, the County of St. Joseph, the State of Indiana, or the United States Federal Government. This certificate is good for one year from the date of issuance and is effective from the date entered herein. Plans are on file and open for public inspection at the office of the Historic Preservation Commission of South Bend and St. Joseph County, 227 West Jefferson Blvd., Suite 1400 S, South Bend, Indiana, during normal business hours. THIS CERTIFICATE IS NOT TRANSFERABLE NAME OF APPLICANT:Kevin & Aimee Buccellato CERTIFICATE ISSUED BY: Kate Himick Historic Preservation Specialist POST IN A CONSPICUOUS PLACE ON THE STREET SIDE OF THE PROJECT UNTIL COMPLETION OF ALL WORK. Phone: (574) 235-9371 E-mail: SBSJCHPC@southbendin.gov ROSS VAN OVERBERGHE Historic Preservation Administrator 7/15/2025DATE CERTIFICATE TAKES FORCE:7/15/2026DATE CERTIFICATE EXPIRES: Ord No. 7796-87 East Wayne Street ADMINISTRATIVE APPROVAL 7/14/2025 $20.00 PayPal Transaction ID: 0UC753625L816242X Estimate Amount $7,038.44 RENEW ROOFING LLC 21935 Shirley Dr Goshen, IN 46526 renewroofing18@gmail.com (574) 312-0446 For: Kevin & Aimee Buccellato Job Address: 304 South Twyckenham Drive South Bend, IN 46615 Last Modified: 03/28/2025 ESTIMATE Job Id 2503-6702541-01 Estimate # 0218 Estimate Date 03/28/2025 #Name Line Total 1 Labor $1,200.00 Description: Remove deck boards, railing, old membrane, subfloor and screw down new subfloor out crown molding edge 2 membrane $2,868.44 Description: .060 EPDM black rubber adhered down. 10 year warranty Install with trims and post wrap 3 wood $664.00 Description: Trim boards, Crown molding, boards for railing, misc.. 4 Gutter $1,506.00 Description: 6" half round gutter hung on brackets. Round downspout attached 5 misc $800.00 Description: powerwash railing at home and install new boarded slates in bad spots. Install trim board and transition siding over roof material. Install railing into place and putty in screw holes. 6 optional $0.00 Description: DecTec optional rooftop walkable membrane flooring. upgraded to an 80 mil thickness with a 20 year limited warranty. Fully adhered and seams heat welded for cohesion This optional upgrade would add an additional $1,200 Total $7,038.44 Note: Renew Roofing is fully insured with liability, workers compensation, and bond insurance. *Unexpected structural work needing repair will be a change order. *Painting is not included in this scope of work. *Signing of estimate turns this into an agreement and we are authorized to complete the work. Thankyou-- Elias Martin Date of Acceptance ________________________________________ Signature ________________________________________________ Mule-Hide Products Co., Inc. Page 1 of 3 PDS 09-1305 Product Data Sheet STANDARD BLACK EPDM MEMBRANE PRODUCT DESCRIPTION Revision Date: Sept 2019 Mule-Hide Standard Black EPDM membranes are high performance non-reinforced membranes that stand up to tearing, impacts, punctures and normal roof traffic. The elastomeric properties of the EPDM membranes compensate for thermal shock and building movement. EPDM membranes provide excellent resistance to ozone and aging. The EPDM membranes are manufactured in accordance w ith the guidelines established by the RMA (Rubber Manufacturers Association) and meet or exceed the ASTM Standard Specification D 4637, Type I. Mule-Hide Standard Black EPDM membranes are Fire Retardant (FR) membranes specially formulated to inhibit spread of flame and meet or exceed code body testing criteria for fire retardant roofing membranes. Mule- Hide Standard Black EPDM membranes are available with in-seam tape that is pre-applied to the sheet BASIC USES Can be used as an elastomeric single-ply roofing membrane for new construction and re-roofing applications. May be installed in Ballasted and Fully Adhered roofing systems. SPECIFICATIONS – Mule-Hide .045" and .060" thick Standard Black EPDM Membranes. Physical Properties* Test Method Standards Typical Values .045 .060 Tolerance on Nominal Thickness, % ASTM D 412 + 10 + 10 + 10 Weight, lbm/ft2 (kg/m2) 0.29 (1.4) 0.39 (1.9) Tensile Strength, min, psi(Mpa) ASTM D 412 1305 (9) 1600 (11.0) 1600 (11.0) Elongation, Ultimate, min, % ASTM D 412 300 480 465 Tear Strength, min, lbf/in (kN/m) - (Die C) ASTM D 624 150 (26.3) 200 (35.0) 200 (35.0) Factory Seam Strength, min. ASTM D 816 (Modified) Membrane Rupture Membrane Rupture Membrane Rupture Resistance to Heat Aging** Properties after 4 weeks @ 240oF(116oC) Tensile Strength, min, psi(MPa) Elongation, Ultimate, min, % Tear Resistance, min, lbf/in(kN/m) Linear Dimensional Change, max, % ASTM D 573 ASTM D 412 ASTM D 412 ASTM D 624 ASTM D 1204 1205(8.3) 200 125(21.9) + 1.0 1500(10.3) 225 215 (37.6) -0.4 1450(10.0) 280 215 (37.6) -0.5 Ozone Resistance** Conditions after exposure 100 pphm Ozone in air for 168 hrs @ 104oF(40oC) Specimen is at 50% strain ASTM D 1149 No Cracks No Cracks No Cracks Brittleness Temp., max, deg. F (deg.C) ASTM D 746 -49 (-45) -49 (-45) -49 (-45) Resistance to Water Absorption** After 7 days immersion @ 158oF (70oC), Change in mass, max, % ASTM D 471 +8, -2 +2.0 +2.0 Water Vapor Permeability** MAX. perm mils ASTM E 96 (Proc. B or BW) 0.10 0.05 0.03 Flexibility/Torsion DMA @-40°F ASTM D5279-08 N/A 225 Mpa 225 Mpa Resistance to Outdoor (Ultraviolet) Weathering - Xenon-Arc, exposure, 0.70 W/m2 irradiance,176oF (80oC) black panel temperature ASTM G 155 No Cracks No Crazing 7,560 kJ/m2 3,000 hours No Cracks No Crazing 41,580 kJ/m2 16,500 hours No Cracks No Crazing 41,580 kJ/m2 16,500 hours At 0.35 W/m2 irradiance,176oF (80oC) black panel temperature 6,000 hours 33,000 hours 33,000 hours Fungi Resistance ASTM G21 N/A 0 (no growth) 0 (no growth) Mule-Hide Products Co., Inc. Page 2 of 3 PDS 09-1305 Product Data Sheet MULE-HIDE STANDARD BLACK EPDM MEMBRANE SPECIFICATIONS (continued) PACKAGING Standard Black EPDM (with and with-out tape) are available in a variety of sizes with widths up to 50’ and lengths up to 150’ long. Contact Mule-Hide Products for specific rolls sizes available. BENEFITS & SUPPLEMENTAL STATEMENTS  Can be installed over a variety of roof decks  Outstanding weatherability  Sheets can be pre-taped for labor savings and consistent seam placement  Requires no special equipment to install  Available as a lightweight system  Full line of pre-taped accessories available CODE APPROVALS/COMPLIANCE A variety of Factory Mutual Ratings, Underwriters Laboratories Classifications and Miami-Dade Approvals are available. Contact Mule-Hide Warranty Department for additional information. Meets or exceeds requirements of ASTM D 4637, Type I for non-reinforced EPDM single-ply roofing membranes. INSTALLATION INSTRUCTIONS 1) Fully Adhered Roofing System a) Approved insulation shall be attached to the roof deck with an approved insulation adhesive or approved fasteners and plates. b) The field of the roof is fully adhered to the substrate with Mule-Hide membrane adhesive. 2) Ballasted Roofing System a) Approved insulation to be loosely laid to the deck. b) Roofing membrane is loosely laid over insulation and ballasted with washed river rock or pavers. 3) The membrane is required to be mechanically attached at the base of all vertical surfaces, roof edges, and angle changes greater than 2:12. 4) All seams are to be constructed with seam tape and tape primer, and checked for voids. 5) All details will be done in accordance with Mule-Hide details. 6) On projects where a Mule-Hide Standard or Premium Warranty is requested, an authorized Mule-Hide representative shall inspect all completed work. This is only a brief summary and not the complete specification. The Mule-Hide Specifications, Details, Technical Bulletins, and associated documents should be thoroughly reviewed prior to starting any project. Contact Mule-Hide Products for additional information. *Typical properties and characteristics are based on samples tested and are not guaranteed for all samples of this product. This data and information is intended as a guide and does not reflect the specification range for any particular property of this product. **Not a Quality Control Test due to the time required for the test or the complexity of the test. However, all tests run on a statistical basis to ensure overall long-term performance of the sheeting. LEED Information Pre-consumer Recycled Content 5% Post-consumer Recycled Content 0% Manufacturing Location Carlisle, PA or Greenville, IL Solar Reflectance Index (SRI) 9 Mule-Hide Products Co., Inc. Page 3 of 3 PDS 09-1305 Product Data Sheet MULE-HIDE STANDARD BLACK EPDM MEMBRANE STORAGE & HANDLING  Use proper stacking procedures to ensure sufficient stability of the materials.  Surfaces may be slippery when wet, or due to frost and ice build-up. Exercise caution to prevent falls.  Exercise care when working near edge of roof.  Store Mule-Hide membrane in original wrappings in a cool, shaded area. Cover with light colored, breathable, waterproof tarpaulins.  Pre-Taped membranes should not be exposed to prolonged jobsite storage temperatures in excess of 90ºF (32ºC), otherwise the shelf life of the Pre-Tape may be affected.  When using pre-taped membranes in warm, sunny weather, shade the tape end of the rolls until ready to use.  Mule-Hide Pre-Tape has a shelf life of one year. PROTECTION & SAFETY Mule-Hide maintains Safety Data Sheets on all of its non-exempt products. Safety Data Sheets contain health and safety information for your development of appropriate product handling procedures to protect your employees and customers. Mule-Hide's Safety Data Sheets should be read and understood by all of your supervisory personnel and employees before using Mule-Hide products in your facilities. ADDITIONAL INFORMATION The information given on this PDS is subject to change without notice. Always check the Mule -Hide website at www.mulehide.com for the latest information, changes and updates or contact Mule-Hide Products Company at 800-786-1492. DISCLAIMER The statements provided concerning the material shown are intended as a guide for material usage and are believed to be true and accurate at the time of printing. No statement made by anyone may supersede this information, except when done in writing by Mule-Hide Products Co., Inc. Since the manner of use is beyond our control, Mule-Hide does not authorize anyone to make any warranty of merchantability or fitness for any particular purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material. This product may be eligible for a Mule-Hide warranty, please check the Mule-Hide website at www.mulehide.com or contact Mule-Hide directly at 800-786-1492 for details. Buyer and user accept the product under these conditions and assume the risk of any failure, any injury person or property (including that of the user), loss or liability resulting from the handling, storage or use of the product whether o r not it is handled, stored or used in accordance with the directions or specifications. Mule-Hide must be notified in writing of any claims and be given the opportunity to inspect the alleged failure before repairs are made. 5″ x .027 Half Round Aluminum Gutter Home 5" Half Round Gutter 5″ x .027 Half Round Aluminum Gutter Gutter can be shipped in lengths of 6, 10, 15 and 19 feet. Gutter can also be shipped at 20 & 26 foot lengths, but is considered and rated as excessive length by freight companies. (6′ maximum lengths shipped via UPS) Our unique front lip design adds 3 times the front-to-back strength compared to traditional front roll out gutters. Available in several colors, featuring a low gloss baked-on enamel nish which can be painted. See Color Chart below. Gutter will be shipped in our custom corrugated Gutter Box, which is extremely durable to withstand the possibilities of shipping damage. We can nest 4-6 pieces of gutter per box depending on the size of gutter and shipping destination. Gutter Box is $2.50 per foot, and we will add the cost to your order. Price shown is per foot, please enter the total number of feet needed in the Quantity box. IMPORTANT: When you’re checking out, you’ll have the opportunity to specify the quantity of each length of gutter you need. You’ll enter this info in the “Order Notes & Item Length Specs” box at checkout. One to ve pieces of gutter can be sent UPS in 6′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote. Each gutter and downspout order is unique at Classic Gutter Systems. Once you’ve placed your order on this website, you’ll be contacted within 48 hours with a complete, detailed quote including packaging and shipping costs. 1 $3.25 – $4.10 Color Choose an option ﹣﹢Add to cart // 269.665.2700 info@classicgutters.com 269.665.2700 info@classicgutters.com Home Ordering Info My Account FAQs Contact Catalog Top Menu Top Menu Products About Us Learning Center Estimate Forms Installations $0.00 0 󬁑 󬁑 SKU: N/A Tag: Gutter Systems Category: 5" Half Round Gutter Description Additional information Related products ALUMINUM GUTTER SCREEN, 3' LENGTHS $8.60 – $10.75 Select options 8" HALF ROUND COPPER GUTTER $14.50 Select options 5" OPEN CURL K-STYLE DECORATIVE ACCESSORY $6.90 – $9.90 Select options SPHERICAL END CAPS FOR HALF ROUND GUTTER, REVERSIBLE $12.50 – $24.50 Select options 6" X .032 HALF ROUND ALUMINUM GUTTER $4.30 – $4.70 Select options GUTTER SHIPPING BOX (PRICED PER FOOT) $2.75 Add to cart NATIONWIDE Classic Gutter Systems, LLC 155 McCollum, Galesburg, MI 49053 269.665.2700 | email us @2025 Classic Gutter Systems LLC | All Rights Reserved