Laserfiche WebLink
Technical Data Sheet <br />�i►S'i�i�'jr'�ir�Ls <br />Pavement Products & Equipment <br />PRODUCT DESCRIPTION <br />SAFE RIDE BICYCLE <br />LANE COATING SMT158 <br />Safe Ride Bicycle Lane Coating is a 100%Acrylic <br />Self-Crosslinking Polymer Emulsion designed as a <br />highly durable pavement color coating. Safe Ride is <br />fortified with specifically graded aggregate providing <br />a textured surface for slip -resistance and added <br />durability. Safe Ride bicycle lane coating meets the <br />Manual on Uniform Traffic Control Devices (MUTCD) <br />requirements for Green color night time and day time <br />chromaticity ratings. Safe Ride is a single component <br />ready -to -apply product. <br />RECOMMENDED USES <br />Safe Ride is primarily designed for bicycle lanes on <br />asphalt streets and roads. Safe Ride provides a Safe <br />Zone for bicyclists on city streets and other high <br />traffic roadways. <br />COVERAGE <br />Typically one gallon of Safe Ride Bicycle Lane Coating <br />will cover approximately 50 square feet per coat. <br />Two to three coats are recommended for optimum <br />durability and performance. <br />SURFACE PREPARATION <br />Surface must be clean and free from all loose material, <br />dirt, grease, and oil. <br />COLOR <br />Bright green. Meets the Manual on Uniform Traffic <br />Control Devices (MUTCD) requirements for Green <br />color night time and day time chromaticity ratings. <br />APPLICATION EQUIPMENT <br />Spraying is the preferred method of application.A <br />textured spray unit is recommended. Safe Ride can <br />also be applied by brush or roller. <br />MIXING PROCEDURES <br />Safe Ride is ready to use. Stir material thoroughly <br />before applying. <br />APPLICATION <br />For optimum performance and durability, apply a <br />minimum of two coats of Safe Ride Bicycle Lane Coating. <br />REVISED 12/13/16 <br />Allow first coat to dry thoroughly before applying <br />second coat. A third coat of Safe Ride may be applied in <br />high traffic/high wear areas for added durability. <br />CHARACTERISTICS <br />REQUIREMENT <br />Resin <br />Cross -linking Acrylic <br />Solids by Weight <br />>74% <br />Solids by Volume <br />>60% <br />Weight per Gallon <br />13.5 Ibs.lgal ±.5 Ile. <br />Non -reactive Fillers <br /><38% <br />Silica Sand <br />> 15% <br />Volatile Organic Compounds (VOC) <br /><50 grams per liter <br />Boiling Range <br />Above 212OF <br />Vapor Density <br />Heavier than Air <br />Flashpoint ASTM D3278 <br />>450°F <br />Viscosity @ 70OF (20°C) <br />90-120 KU <br />Dry mil thickness per coat <br />20 to 25 mils <br />Recommended Number of Coats <br />2-3 coats <br />Dry Time (to re -coat) @ 50OF (I OOC) @ 50% RH <br />45 minutes <br />Dry Time (to re -coat) @ 90OF (32°C) @ 50% RH <br />25 minutes <br />85% Cure (for traffic) @ 50°F (I OOC) @ SO% RH <br />5 to 7 hours <br />85% Cure (for traffic) @ 90OF (32'C) @ 50% RH <br />I to 3 hours <br />ASTM 2486 Scrub Resistance (25 dry mils) 50% <br />applied as a per manufacturers specifications <br />6000 cycles to max <br />loss of 50% coating <br />Dry mil build thickness per coat <br />20 to 25 mils <br />Temp. limits for service (of cured material) <br />-40OF to I50OF <br />Friction with locked wheeled tester at 30 mph <br />>50 FN30R <br />Pedestrian Friction ASTM E303 British Pendulum <br />>75 BPN <br />PROTECT CONTAINERS FROM FREEZING <br />WARRANTY AND DISCLAIMER <br />The statements made on this specification sheet are believed <br />to be true and accurate and are intended to provide a guide <br />for approved application practices.As workmanship, weather, <br />construction, condition of pavement, tools utilized, and other <br />variables affecting results are all beyond our control, the <br />manufacturer warrants only that the material conforms to <br />product specifications and any liability to the buyer or user of <br />this product is limited to the replacement value of the product <br />only.The manufacturer expressly disclaims any implied warranties <br />of merchantability or fitness for a particular purpose.Warranty is <br />void on multi -coat applications if material made by other <br />manufacturers is used with this product. <br />Form No.:SMT-158 <br />Revised: 12/16 Copyright©2016, Seal Master All rights reserved. <br />