HomeMy WebLinkAboutOpening of Bids - One (1) or More, 2020 or Newer, Emergency Medical Vehicle – Spec P - Horton Emergency VehiclesBID NAME
FOR BIDS DUE
SPECIFICATIONS
CITY OF SOUTH BEND
Spec P — One (1) or More 2020 or Newer Emergency Medical Vehicle
November 10; 9:00 a.m.
Pursuant to notices given, the undersigned offers bid(s) to the City of South Bend in accordance
with the following attachment(s) which specify the class or item number or description, quantity,
unit, unit price.
SPEC P - ONE (1) OR MORE 2020 OR NEWER EMEGENCY MEDICAL VEHICLE
It is the intent of these specifications to describe an emergency medical vehicle for the City of
South Bend. All units bid must have been manufactured in the U.S.A. The unit shall be bid as a
fully equipped complete Emergency Medical Vehicle as described in the following specification.
No partial or split bids will be accepted.
The City of South Bend reserves the right to reject any and all bids or to accept a full or partial
award of the bid or bids and to waive any irregularities or informalities which, in its judgment,
will be in the best interest of the City of South Bend.
The Board will award the bid to the lowest responsible and responsive bidder. If the bid is not
awarded to the lowest bidder, the factors used to justify the awards will be stated in writing at the
request of any bidder.
These are minimum specifications. Any variation from the specifications must be spelled out on
a separate exception list and attached to your bid in order for the bid to be valid. Any items not
listed on the exception sheet will be assumed to be part of the unit.
Any exceptions to the following specifications must be noted by the dealer at the time of bidding
in order for the bid to be valid. Vendor to complete bid proposal, options, and nondiscrimination
commitment contained in this bid specification and attach to the submitted bid.
AMBULANCE SPECIFICATIONS
TYPE I
CLASS I, CONFIGURATION A
2020 STAR -OF -LIFE CERTIFIED AMBULANCE
170" X 96"
The Emergency Medical Vehicle described in this specification is designed to meet
or exceed the requirements of the Federal Ambulance Specification KKK-A-1822
Revision F, and AMD Standards 001-009.
NOTE: Throughout the written Federal Ambulance Specification KKK-A-1822, there
are frequent references to items to be included WHEN SPECIFIED. The
manufacturer will build into a given ambulance any WHEN SPECIFIED item, but
such items may not be included in the attached specifications.
"OR APPROVED EQUAL" CLAUSE
To expedite the purchase of this Ambulance, a generic set of specifications has been
used. The mention in the specification of chassis, equipment, or material by brand
name or by such specified description of same hereby made, is intended to convey
to the bidder's understanding, the degree of excellence required. Any article,
equipment, or material which shall conform to the standards and excellence so
established, and is of equal merit, strength, durability, and appearance to perform the
desired function, is deemed eligible for offer as a substitute. The qualification of the
offering shall be judged as to their conformance with these specifications. Any
equipment offered other than herein specified shall be subject to a competitive
demonstration and evaluation by the using department. Such demonstration to be
provided on request within ten working days after the receipt of bids and the result of
that demonstration and evaluation shall be of prime importance in the
recommendation to the governing body for the final contract award. The result of that
demonstration and evaluation shall be of prime importance in the recommendation to
the governing body for the final contact award.
Any exception to these specifications shall be so marked at the area, (Does Your Bid
Comply? YES _NO_) and the "OR APPROVED EQUAL" item shall be listed using
the item numbering system within this document.
1.0 INSTRUCTIONS TO BIDDERS
This specification covers a new commercially built surface emergency medical care
vehicle herein after referred to as ambulance or vehicle. A vehicle in compliance
with this specification shall be defined as a standard ambulance. This vehicle shall
be in accord with the Ambulance Design Criteria of the National Highway Traffic
Administration, U.S. Department of Transportation, Washington D.C. This bid
specification is based on the Federal Ambulance Specification KKK-A-1822F
effective July 2007.
The purpose of this document is to provide minimum specifications and test
parameters for the manufacture of an emergency medical care vehicle that meets
the needs and desires of this agency. It establishes essential criteria for the design,
performance, equipment, and appearance of the vehicle. All dimensions listed are
given as the approximate sizes required to meet the needs of this department. The
object is to provide a vehicle that is in accordance with nationally recognized
guidelines. All vendors and manufacturers must meet all state and local regulations
regarding the manufacturing, licensing, and sale of emergency rescue vehicles and
ambulances within the state.
KKK Federal Specifications
This Ambulance is required to conform to KKK Federal Specification for the Star of
Life Ambulance. The City is not required by Law to be KKK-A-1822F Change Notice
8 compliant to meet SAE J3026 Ambulance Patient Compartment Seating Integrity
and Occupant Restraint Standards, SAE J3027 Ambulance Litter Integrity, Retention,
and Patient Restraint Standards. Bidder shall be a KKK-A-1822F Change Notice 8
compliant to meet SAE J3026 Ambulance Patient Compartment Seating Integrity and
Occupant Restraint Standards, and SAE J3027 Ambulance Litter Integrity, Retention,
and Patient Restraint Standards. Bidder shall be KKK-A-1822F Change Notice 9
compliant to meet SAE J3043 Ambulance Equipment Mounts; Interior Stowage
Accommodations; Equipment Mounting Devices: Installed Oxygen cylinder, cardiac
monitor, and fire extinguisher mounting devices shall meet the performance
requirements of SAE J3043. Bidder shall be a KKK-A_1822F Change Notice 10
compliant to meet: SAE J3058 Ambulance Interior Storage Compartment Integrity;
SAE J3057 Ambulance Modular Body Evaluation -Quasi Static Loading for Type I
and Type III Modular Ambulance Bodies; SAE J3102 Ambulance Patient
Compartment Structural Integrity Test to Support SAE J3027 Compliant Litter
Systems; SAE J3043 Ambulance Equipment Mounts, Interior Stowage
Accommodations, Equipment Mounting Devices: Installed suction mounting; to
conform to all applicable requirements.
Type I: Specialty cab and chassis with containerized modular body.
Class I: Two -rear wheel driven (4x2).
Configuration A: Elevating cot and squad bench for ALS (3.1.5.1/3.15.3 of F-Spec).
This is an engineer, design, construct, and deliver type specification and it is not the
intention of this agency to write out vendors or manufacturers of similar or equal
equipment of the types specified. It should be noted, however, that this specification
is written around the specific needs of this department. With the intent to standardize
certain components, specific brands have been specified in certain places. This has
been done to establish a certain standard of quality. Other brands will be accepted
providing the vendor or manufacturer details how another brand will meet or exceed
the quality of the actual brand specified. Because of this, the Review Board reserves
the right to accept or reject any and/or all bids.
The emergency medical care vehicle, chassis, ambulance body, equipment, devices,
medical accessories, and electronic equipment to be delivered under this contract
shall be standard commercial products that meet or exceed the requirements of this
specification. The ambulance shall comply with all Federal Motor Vehicle Safety
Standards (FMVSS) and Federal regulations applicable or specified for the year of
A N
manufacture. The chassis, components, and optional items shall be represented in
the manufacturer's current technical data. Materials used in the construction shall be
new and not less than the quality conforming to current engineering and
manufacturing practices. Materials shall be free of defects and shall be suitable for
the intended use.
Any exceptions to these specifications must be clearly pointed out. Otherwise, it will
be considered that the items offered are in strict compliance with the written
specifications and that the successful bidder will be responsible for delivering a
vehicle meeting these specifications. Any exceptions must be marked as such within
the body of the bid and explained on a separate page marked "EXCEPTIONS".
Bids taking total exception to these specifications will not be accepted.
1.1 INFORMATION AND DESCRIPTIVE MATERIAL
The bidder must furnish all information requested in the space provided on the bid
form. The manufacturer must supply a dated copy of their Ford QVM certificate as
proof that they are a current member of the Qualified Vehicle Modifier Program. This
requirement must be met even if the chassis specified is not a Ford to ensure that
chassis modification standards meet a desired minimum level. The manufacturer
must also supply the D-spec certification for this particular type, at least one [1]
complete set of sketches, descriptive literature, and complete specifications covering
the products offered. Bids not meeting this requirement will be considered non-
responsive and rejected.
1.2 PRICES AND PAYMENTS
All bid prices shall be on a F.O.B. destination and acceptance basis at the
Purchaser's specified location. These Prices shall be complete and include
warranty. Payment shall be made in accordance with these specifications and the
Bid Proposal submitted by the Bidder. Payment shall be made upon acceptance of
the vehicle(s) and equipment specified under these specifications. All bid prices and
conditions must be specified on the bid proposal form. Bid prices shall be valid for at
least thirty- [30] days from the date of the bid opening or as otherwise specified on
the bid proposal form. Full payment shall be made as each unit is received,
inspected, and found to comply with the procurement specifications.
YZN_
Y N
9111111111111il
1.2.1 Price Guarantee
The successful bidder shall guarantee the bid price for a minimum of 12 months to
the City of South Bend. The City reserves the right to purchase an additional unit at
this price within 12 months of bid award.
1.3 GENERAL LIABILITY
Bidders are required to submit with their bids a Certificate of Liability Insurance in the
amount of five million dollars (5,000,000) in general liability as issued by the bidder's
insurance company.
Y�Ci N_
1.4 WARRANTY
The successful manufacturer shall provide a three (3) year/36,000 mile warranty on
the vehicle which covers defective parts and/or components, the improper choice of
materials, parts, and/or components, improper design or engineering, and poor or
improper workmanship or quality control techniques. The warranty shall cover the
complete vehicle and shall include all costs for labor and parts or materials that are
required to correct all deficiencies.
If travel is required for warranty repairs, transportation of the unit is the responsibility
of the successful bidder. Transportation must take place within the next normal
working day, or the responsible party will be charged $100 per day late fee.
There shall be provided a lifetime electrical warranty that covers all conversion circuit
boards, harnesses, switches, circuit breakers, and relays.
There shall be provided a lifetime transferable modular body structural warranty.
The term transferable is to cover the transfer of the warranty to a second purchaser
should the department sell this unit later. The lifetime structural warranty period shall
also remain in effect should the modular body be remounted onto a new chassis.
This remount must be performed at a service center authorized by the original
manufacturer.
Y N
1.5 WARRANTY SURETY
To ensure quality, service, and full compliance to the above warranties, the vehicle,
with the exception of the chassis, must be constructed by the ambulance
manufacturer. Additional elements constructed and installed "in house" are required
to ensure service and parts availability. Subcontractors or lease/rental agreements
to outside agencies will fail to meet this requirement.
• Does the ambulance manufacturer as the prime contractor construct the modular
body?
Does the ambulance manufacturer as the prime contractor apply paint?
• Are interior cabinets constructed and installed by the ambulance manufacturer as
the prime contractor?
• Are the wiring harnesses, circuit boards, and 02 systems assembled, installed
and tested by the ambulance manufacturer as the prime contractor?
• Is the upholstery for seat cushions, head pads, and backrests assembled and
installed by the ambulance manufacturer as the prime contractor?
Y&N_
1.6 DELIVERY
Bidder must state an accurate delivery date which shall not exceed 180 days
from the date of bid award. Due to the age of the City's existing fleet, it is imperative
that the unit be delivered as quickly as possible. Stated delivery lead time will be
included as an integral part of our bid selection process. FOB Central Services.
Liquidated damages of $100.00 dollars per day, per unit will be assessed by the City and
deducted from any monies owed to the vendor if the units are not delivered complete to
the City by the stated date. The unit and all related paperwork is to be delivered to:
Central Services Division
1045 West Sample Street
South Bend, Indiana 46619
The Board will award the bid to the lowest responsible and responsive bidder. If the bid
is not awarded to the lowest bidder, the factors used to justify the awards will be stated
in writing at the request of any bidder.
The Board reserves the right to reject any and/or all bids or portions thereof and
to waive any irregularities or informalities. Y N
SERVICE FACILITY
The successful bidder must have access to a service facility. Bidders must list below
the nearest service facility and parts department to the purchaser.
Facility Name: }L Nf,9C4 ,cam
Address: � Jc� � ice. 614yye—C4 1, dL� 431�3
Phone Number:
Contact Name: � 4-nj
Approximate Miles 96Q ✓yl� W,_ �r
From Purchaser:
YX_N
1.7 REFERENCES
All bidders must submit a list containing a minimum of ten [10] customers who are
operating a similar model ambulance as described in this specification. The
customer reference list shall contain the Department name, address, phone number
and contact person.
Y N
1.8 QUALITY ASSURANCE
To ensure the purchaser that proper engineering and production control guidelines
have been implemented, the ambulance manufacturer shall employ an integrated
quality and process control program including specific process controls for facets of
the manufacturing process deemed to be critical. These critical elements of the
process shall be documented and that documentation shall be available not only to
manufacturing personnel but also customers who visit the manufacturing facilities.
The critical elements shall be denoted on the vehicle control document, which
accompanies the vehicle through the manufacturing process. A sample of this
document shall be available to the purchaser upon request. A continuous series of
inspections shall be performed and signed off on the vehicle control document and
shall include but not be limited to the following:
Visual inspection of the body, welds, and exterior attachments.
Visual and mechanical inspection of the heater/air conditioning lines, cables,
grommets, valve connections, clamps, mounting brackets, belts, etc.
Visual inspection of cabinets, sliding/hinged cabinet doors, moldings, flooring, walls,
headliner, and cushions.
Visual inspection of exterior paint, decals, and lettering.
Operational inspection of all electrical systems. This must consist of tests of battery
voltage, electrical load tests, alternator output, beacons, flashers, siren, interior
lighting, compartment lighting, power. exhaust vent, scene lights, load lights, chassis
lights, silent signal lights/buzzer, heat/cool unit, and any optional electrical devices as
furnished by the manufacturer. The current requirements of each device tested must
be noted on an inspection sheet together with the total current requirements.
The oxygen and vacuum systems shall be tested both prior to and after installation to
meet the requirements as listed in those individual sections of this specification. Test
data indicating temperature, pressure, timing, flow, etc., shall be recorded.
All chassis fluid levels shall be checked and filled to capacity. All doors, locks,
windows, tires, etc. shall be inspected for proper operation and/or condition.
The completed vehicle must be test driven a minimum of ten [10] miles on paved
highways and [3] miles on rough terrain to check handling, brakes, acceleration, and
noises. A water spray test and visual inspection shall be performed after the road
test.
1.9 BID BOND REQUIREMENT
All bidders are required to furnish a bid surety in the amount of ten percent (10%) of
the total price of the proposal. The surety shall be in the form of a bond only. Any
surety in the form of a cashier's check, certified check or money order shall be
considered non -responsive and shall be cause for rejection of the bid proposal.
1.10 SINGLE BIDDER PER MANUFACTURER
Multiple bids from different manufacturers but represented by the same firm will not
be accepted. Bids offered directly from manufacturers shall indicate if a local dealer /
representative will be involved.
Alternate bids from the same bidder will be accepted (for example, entire vehicle
including chassis and without chassis), providing each bid has its own bid bond.
Alternate bids within the original bid will not be accepted.
Bids from the same manufacturer but different dealers will not be allowed to prevent
complimentary bids being offered and to ensure service from local dealer
representatives. It is the desire of this department to have a dealer organization
Y;�_N
Y N
domiciled in the State of Indiana so that local service can be assured.
Y N
1.11 WITHDRAWAL OF BID
A Bidder may withdraw a bid any time prior to expiration of the period during which
bids may be submitted by a written request signed in the same manner and by the
same person who signed the Proposal. No bid may be withdrawn, modified, or
otherwise changed once the bids have been opened. It will be assumed that each
Bidder has thoroughly and completely familiarized themselves with these
specifications at the time of the bid. Modifications to a bid, once submitted will not be
permitted. Simply stated, if any item, feature, options, etc. Is not stated in writing in
the Bidder's proposal, it will not be considered. Bidders are cautioned that verbal or
written modifications to already opened bids will not be valid, nor considered ethical
and the comparison and selection of bid award will proceed only from what is stated
in Bidder's written proposal.
Y N
1.12 AUTHORITY TO PURCHASE FROM EXISTING CONTRACTS
All bidders submitting a response to this Invitation to Bid or Request for Proposal
agree that such response also constitutes a bid to all governmental agencies under
the same conditions, for the same contract price, and for the same effective period
as this bid, should the bidder feel it is in their best interest to do so.
Each governmental agency desiring to accept these bids and make an award thereof
shall do so independently of any other governmental agency. Each agency shall be
responsible for its own purchases and each shall be liable only for materials and / or
services ordered and received by it, and no agency assumes any liability by virtue of
this bid. This agreement in no way restricts or interferes with the right of any
governmental agency to bid any or all items.
Bids will be made available to other municipal and governmental agencies within the
United States of America. Unit purchases after a period of one year will be adjusted
to reflect to the established Producers Price Index (PPI), U.S. Labor Dept., Bureau of
Statistics, Series PCU3713 # 2A, Emergency Vehicles.
YxN
1.13 ENGINEERING CAPABILITY
To demonstrate your company's abilities and to show understanding of the written
bid specifications, each manufacturer must submit with the bid, scale drawings of the
vehicle it proposes to supply. Drawings must be "design and construct" drawings
that will be used in the manufacture of the vehicle. At a minimum they must show
overall dimensions, compartment sizes, lighting package, and major specified
options. The drawings should show the front, rear, right side, and the left side of the
exterior. They should also include the interior bulkhead, street side, curb side
cabinet plans and the interior floor plan layout. The reproduction of the drawing
furnished with the bid will not be acceptable as each manufacturer utilizes different
material sizes and construction techniques.
��
1.14 PLANT FACILITY
To demonstrate a Manufacturers capability, pictures of the interior of the plant facility
during production hours must be submitted. A minimum of four plant photographs
and one office photograph shall be supplied.
nollill
15 EXPERIMENTAL VEHICLES
It is not the intent of these specifications to call for an unusual or experimental
vehicle(s).
YX N_
1.16 INSPECTION FACILITY
In the event it is deemed necessary for this agency to inspect the vehicle(s) at the
primary manufacturer location, a temperature -controlled inspection area separate
from the production facility shall be provided. It shall be painted a color to facilitate
ease of inspection and shall be lighted in a manner to eliminate shadows in the
inspection facility. Work areas with desks, phones, and the necessary tools to
accomplish a detailed inspection shall be provided.
Y N
1.17 PRE -CONSTRUCTION CONFERENCE
The successful Contractor shall be required prior to manufacturing to have a Pre -
Construction conference at the site of his choosing with representatives of this
agency to finalize all the construction details. If the bidder requires the conference to
be held at a location other than that of the purchaser, the bidder at his/her expense
shall provide transportation, lodging and meals, etc. for three (3) people designated
by the purchaser. If this meeting is to occur at a location more than 250 miles from
the purchaser's location, the transportation shall be by commercial air carrier.
Y_KN_
1.18 INSPECTION VISITS
Accompanied by a Dealer Representative, two (2) members of the City of South
Bend, Indiana, or its designees will travel to the successful bidder's facility for the
purpose of inspecting the vehicle for compliance to the specifications and for the
overall quality of the vehicle.
Costs shall include air transportation on a major commercial carrier to the nearest
airport (if ground transportation exceeds 250 miles), individual rooms, and meals.
Trips shall be one (1) post paint or an in progress inspection and one (1) for final
inspection
Inspections shall be scheduled to be conducted during weekdays, including travel
time.
YxN
1.19 GENERAL VEHICLE DESIGN. TYPE. AND FLOORPLAN
The ambulance and the allied equipment furnished under this specification shall be
the manufacturer's current commercial vehicle of the type and class specified. The
ambulance shall be complete with the operating accessories as specified herein and
furnished with such modifications and attachments as may be necessary or specified
to enable the vehicle to function reliably and efficiently in sustained operation. The
design of the vehicle and the specified equipment shall permit accessibility for
servicing, replacement, and adjustment of component parts and accessories with
minimum disturbance to other components and systems. The term "HEAVY DUTY"
as used to describe an item shall mean in excess of the usual quantity, quality, or
capacity that is normally supplied with the standard production vehicle or component.
1.20 COMPLETED VEHICLE DIMENSIONAL PARAMET
The vehicle furnished shall comply with the following dimensions at curb weight:
Length, overall (including rear step)
Width, Exterior (excluding mirrors)
Wheelbase
Height, Rear Loading
Height, Ground to Step
Ground Clearance
Length, Patient Compartment Interior
Aisle Space with Cot Installed
Width Between Wheel Wells
1.21 CURB WEIGHT
293" Maximum
98"
173-176"
33" Maximum
17.5"
5.5"
167.25"
12"
46" minimum
The curb weight is the total weight of the complete ambulance and is defined as the
chassis, cab, body, and minimum required equipment as required by KKK-A-1822F,
and includes a full complement of fuel, lubricants, and coolant shall meet Federal
Requirements.
1.22 PAYLOAD ALLOWANCE
A minimum of 6,000 pounds will be allowed over and above the curb weight for
personnel, patient, and miscellaneous support equipment.
1.23 INTERIOR HEADROOM
73" of interior headroom shall be provided inside the patient area of the body. It shall
be free of obstructions for the Occupants safety and shall meet or exceed all
transportation and regulatory requirements.
Y N
Y N
Y N
tam
1.24 TECHNICAL REQUIREMENTS CAB/CHASSIS
The ambulance shall be a Type I, Class I, Medium Duty and shall have a chassis
furnished with a two -door cab. The cab/chassis shall be suitable for subsequent
mounting of a modular (containerized) transferable equipped ambulance body
conforming to the requirements specified herein.
2.0 CHASSIS MODEL AND TYPE
The cab/chassis requirement of this specification is a 2012 or newer 42 cab and
chassis, 168-170" wheelbase, 20,000-pound GVWR package, and equipped as
follows:
Vehicle Configuration:
HEAVY DUTY, DIESEL -POWERED CONVENTIONAL CHASSIS
ONLY 2018 or NEWER MODEL YEAR SPECIFIED
SET BACK AXLE - TRUCK
SINGLE -AXLE STRAIGHT TRUCK PROVISION
LH PRIMARY STEERING LOCATION
General Service:
TRUCK CONFIGURATION
CERTIFIED FOR USA (EXCLUDING CALIFORNIA AND CARB OPT -IN STATES)
RESCUE AND EMERGENCY BUSINESS SEGMENT
TERRAIN/DUTY: 100% (ALL) OF THE TIME, IN TRANSIT, IS SPENT ON PAVED
ROADS
MAXIMUM 8% EXPECTED GRADE
SMOOTH CONCRETE OR ASPHALT PAVEMENT - MOST SEVERE IN -TRANSIT
(BETWEEN SITES) ROAD SURFACE
MEDIUM TRUCK WARRANTY
EXPECTED FRONT AXLE LOAD: 8,000 lbs.
EXPECTED REAR DRIVE AXLE LOAD: 12,000 lbs.
GROSS VEHICLE WEIGHT CAPACITY: 20,000 lbs.
Truck Service:
AMBULANCE BODY
EXPECTED TRUCK BODY LENGTH: 15.0 ft
Engine:
6-CYLINDER TURBOCHARGED DIESEL, IN -LINE CONFIGURATION. MINIMUM
6.7 LITER DISPLACEMENT, WITH A MINIMUM 260 H.P. AND TORQUE RATING
OF 660 LB/FT.
The following electronic parameters must be programmed into the ECM:
LOW IDLE ADJUST - YES
CRUISE CONTROL SET SPEED SAVE - YES
CRUISE CONTROL ENABLE - YES
CRUISE CONTROL AUTO RESUME - NO
ROAD SPEED LIMIT MPH: 84.0
GEAR DOWN PROTECTION ENABLE - NO
IDLE TIMER SHUTDOWN ENABLE- NO
IDLE TIMER SHUTDOWN/PTO MODE - NO
IDLE TIMER SHUTDOWN/OVERRIDE-NO
Y& N
PTO VEHICLE SPEED LIMIT: 6 MPH
PTO THROTTLE OVERRIDE ENABLE
PTO BRAKE OVERRIDE ENABLE
PTO CLUTCH OVERRIDE ENABLE
PTO SET/RESUME SPEED: 1000.0 RPM
ONE (1) REMOTE PTO SET SPEED
PTO/REMOTE PTO - YES
PTO RPM W/CRSCTL SET SW OR CAT ON/OFF SW: 950.0
PTO RPM INCREMENT: 200.0
MIN RPM FOR PTO: 700.0
MAX RPM FOR PTO: 1000.0
VSS ANTI -TAMPERING - YES
ENGINE MAINTENANCE MONITOR - ENABLE
ENGINE MAINTENANCE MONITOR TYPE - AUTO
REMOTE THROTTLE - DISABLE
POWERTRAIN PROTECTION - DISABLE
Engine Equipment:
2020 EPA/CARB EMISSION CERTIFICATION
ENGINE MOUNTED OIL CHECK AND FILL
AIR INTAKE SHALL INCLUDE AN NFPA COMPLIANT EMBER SCREEN AND A
FIRE RETARDANT AIR CLEANER- DONALDSON OR EQUIVALENT.
MINIMUM 270 AMP QUADRAPAD MOUNT ALTERNATOR WITH AC TAPS
AT LEAST THREE, MATCHING 12 VOLT MAINTENANCE FREE THREADED
STUD BATTERIES WITH A MINIMUM TOTAL 2700 CCA (COLD CRANKING
AMPS).
JUMPSTART STUDS SHOULD BE MOUNTED ON OR NEAR BATTERY TRAY.
BATTERY BOX TO BE OUTBOARD FRAME -MOUNTED UNDER THE CAB, AND
BE EQUIPPED WITH A FRAME GROUND RETURN FOR BATTERY CABLES.
BATTERY BOX COVER SHOULD BE CONSTRUCTED WITH A NON-
CORROSIVE, COMPOSITE MATERIAL.
AIR COMPRESSOR SHOULD BE RATED AT LEAST 15 CUBIC FEET/MINUTE
AND HAVE AN INTERNAL SAFETY VALVE.
STEEL AIR COMPRESSOR DISCHARGE LINE WITH INTEGRAL QUICK -
CONNECT SYSTEM CHARGING VALVE.
FIRE AND EMERGENCY SERVICE VEHICLES ENGINE WARNING SYSTEM.
THE EXHAUST EMISSION SYSTEM MUST COMPLY WITH EPA 2014
REGULATIONS.
THE HORIZONTAL TAILPIPE SHALL EXIT FORWARD OF THE REAR TIRES ON
THE STREET SIDE OF THE VEHICLE AT A 45 DEGREE ANGLE.
FUEL FILTER SHOULD BE SPIN ON TYPE.
ENGINE TO HAVE FULL FLOW OIL FILTER
RADIATOR TO BE METAL ALLOY, AND BE AT LEAST 950 SQ. IN. IN SIZE.
ANTIFREEZE TO BE RATED TO AT LEAST -34 DEGREES F AND CONSIST OF
ETHYLENE GLYCOL PRE -CHARGED SCA.
COOLANT HOSES SHOULD BE RATED AT 300 DEGREES F., GATES BLUE
STRIPE OR EQUIVALENT.
CONSTANT TENSION HOSE CLAMPS FOR COOLANT HOSES.
ALUMINUM FLYWHEEL HOUSING
ELECTRIC GRID AIR INTAKE WARMER
HEAVY DUTY STARTER, DELCO 12V 38MT OR EQUIVALENT, WITH
INTEGRATED MAGNETIC SWITCH
Transmission:
ALLISON 2500 EVS AUTOMATIC TRANSMISSION WITH PTO PROVISION.
Transmission Equipment:
WTEC CALIBRATION - 6 SPEED EVS (PACKAGE 119).
VEHICLE INTERFACE WIRING HARNESS AND BODY BUILDER CONNECTOR
SHOULD BE LOCATED AT THE BACK OF CAB.
ELECTRONIC TRANSMISSION CUSTOMER ACCESS CONNECTOR TO BE
MOUNTED AT THE BACK OF THE CAB.
PLUGS, ENGINE DRAIN, TRANSMISSION DRAIN, AXLES FILL AND AXLES
DRAIN SHOULD BE MAGNETIC TO TRAP INTERNAL SHAVINGS.
TRANSMISSION GEAR SHIFTER SHOULD BE PUSH BUTTON -TYPE,
ELECTRONIC, AND DASH MOUNTED.
WATER TO OIL TRANSMISSION COOLER, MOUNTED IN ENGINE
COMPARTMENT AREA.
TRANSMISSION OIL CHECK AND FILL WITH ELECTRONIC OIL LEVEL CHECK.
TRANSMISSION TO BE FILLED WITH SYNTHETIC FLUID, AND MUST BE CODE
TES-295 COMPLIANT.
Front Axle and Equipment:
FRONT AXLE TO BE I -BEAM TYPE, AND BE RATED AT LEAST 8,000 LBS.
CAM -TYPE FRONT BRAKES SHOULD BE AT LEAST 15" X 5".
FIRE AND EMERGENCY SEVERE SERVICE, NON -ASBESTOS FRONT LINING
CAST IRON FRONT BRAKE DRUMS.
FRONT OIL SEALS TO BE CHICAGO RAWHIDE, SCOTSEAL, OR EQUIVALENT.
FRONT HUB CAPS SHOULD BE VENTED.
FRONT AXLE TO BE EQUIPPED WITH AUTOMATIC FRONT SLACK
ADJUSTERS.
SINGLE POWER STEERING GEAR SHOULD BE HEAVY DUTY, AND BE
EQUIPPED WITH A POWER STEERING PUMP.
POWER STEERING RESERVOIR SHOULD HOLD A MINIMUM OF 1.5 QUARTS.
PETROLEUM BASED SAE 80/90 LUBE FOR FRONT HUBS.
Front Suspension:
8,000# TAPERLEAF FRONT SUSPENSION WITH MAINTENANCE FREE RUBBER
BUSHINGS. SHOULD ALSO HAVE A FRONT STABILIZER BAR AND BE
EQUIPPED WITH HEAVY DUTY SHOCK ABSORBERS.
Rear Axle and Equipment:
REAR AXLE TO BE RATED AT 13,000 LBS.
REAR AXLE RATIO TO MATCH 84 MPH TOP SPEED WITH TRANSMISSION AND
ENGINE COMBINATION.
IRON REAR AXLE CARRIER WITH STANDARD AXLE HOUSING.
HEAVY DUTY DRIVELINE WITH HALF ROUND YOKES.
CAM -TYPE REAR BRAKES TO BE AT LEAST 15" X 6", WITH DOUBLE ANCHOR,
FABRICATED BRAKE SHOES.
BRAKE SHOES TO HAVE FIRE AND EMERGENCY SEVERE SERVICE NON -
ASBESTOS REAR BRAKE LINING.
REAR BRAKE DRUMS TO BE CAST IRON.
REAR OIL SEALS TO BE CHICAGO RAWHIDE, SCOTSEAL, OR EQUIVALENT.
LONGSTROKE 1-DRIVE AXLE SPRING PARKING CHAMBERS
AXLE TO BE EQUIPPED WITH AUTOMATIC REAR SLACK ADJUSTERS.
PETROLEUM BASED SAE 80/90 REAR AXLE LUBE
Rear Suspension:
REAR SUSPENSION TO BE AIR RIDE, AND RATED AT LEAST 12,000 LBS.
SUSPENSION TO BE SET AT LOW -POSITION RIDE HEIGHT.
SUSPENSION SHOULD HAVE A MANUAL DUMP SWITCH FOR AIR BAGS, WITH
AUTOFILL OVERRIDE VALVE AND AIR GAUGE.
REAR AIR SUSPENSION DUMP VALVE SHOULD AUTOFILL WHEN TRUCK IS
RESTARTED, OR WHEN SPEED EXCEEDS 5 MPH. SHOULD ALSO INCLUDE
OVERRIDE CONTROL SWITCH TO PREVENT INADVERTENT RAISING OF
TRUCK DURING PATIENT LOADING/UNLOADING.
SUSPENSION TO HAVE INSTANT RESPONSE REAR SUSPENSION LEVELING
VALVES FOR STABILITY.
REAR STABILIZER BAR AND TRANSVERSE CONTROL RODS
HEAVY DUTY REAR SHOCK ABSORBERS
Brake System:
AIR BRAKE PACKAGE
4S/4M ABS WITHOUT TRACTION CONTROL
REINFORCED NYLON, FABRIC BRAID AND WIRE BRAID CHASSIS AIR LINES
FIBER BRAID PARKING BRAKE HOSE
STANDARD BRAKE SYSTEM VALVES
RELAY VALVE WITH 5-8 PSI CRACK PRESSURE, NO REAR PROPORTIONING
VALVE
WABCO SS1200 WITH SPIN ON DESICCANT FILTER
STEEL AIR BRAKE RESERVOIRS
STANDARD AIR SYSTEM PRESSURE PROTECTION SYSTEM
BENDIX DV-2 AUTO DRAIN VALVE WITH HEATER — PRIMARY WET TANK
Ambulance Body Builder Connections:
HANGER/SUPPORT
UPGRADED CHASSIS MULTIPLEXING UNIT
UPGRADED BULKHEAD MULTIPLEXING UNIT
Wheelbase & Frame:
170-174" WHEELBASE, OR MANUFACTURER'S SETTING TO ACHIEVE 102-105"
CA. MINIMUM 80,000 PSI FRAME RAILS, TO ACHIEVE AT LEAST 10.74
SECTION MODULUS, AND AN RBM RATING OF NO LESS THAN 859,200 IN.
LBS.
63-72" REAR FRAME OVERHANG
SQUARE END OF FRAME
FRONT CLOSING CROSSMEMBER
STANDARD WEIGHT ENGINE CROSSMEMBER
STANDARD MIDSHIP #1 CROSSMEMBER
STANDARD REARMOST CROSSMEMBER
STANDARD SUSPENSION CROSSMEMBER
Chassis Equipment:
CHROMED STEEL BUMPER WITH LH AND RH CUTOUTS FOR SPEAKERS.
FRONT TOW HOOKS - FRAME MOUNTED.
BUMPER MOUNTING FOR SINGLE LICENSE PLATE.
REAR MUDFLAPS TO BE INSTALLED BY BODY COMPANY
CLEAR FRAME RAILS FROM BACK OF CAB TO FRONT REAR SUSPENSION
BRACKET, BOTH RAILS OUTBOARD.
GRADE 8 THREADED FRAME FASTENERS.
Fuel Tanks:
50 GALLON MINIMUM FUEL CAPACITY.
PLAIN STEP FINISH.
FUEL TANK CAP.
FUEL FILTER/WATER SEPARATOR MOUNTED IN ENGINE COMPARTMENT.
FUEL SYSTEM TO BE EQUIPPED WITH PRIMER PUMP, IN THE EVENT THE
TRUCK RUNS OUT OF FUEL.
REINFORCED NYLON FUEL HOSE.
Tires:
245/70R19.5 12-PLY RADIAL FRONT TIRES: GOODYEAR G647RSS OR
EQUIVALENT
245/70R19.5 12-PLY RADIAL REAR TIRES: GOODYEAR G622RSD OR
EQUIVALENT
Hubs:
ALUMINUM FRONT HUBS WITH PRE-SET BEARINGS
ALUMINUM REAR HUBS WITH PRE-SET BEARINGS
Wheels:
19.5 X 7.50 10-HUB PILOT ALUMINUM DISC FRONT WHEELS.
19.5 X 7.50 10-HUB PILOT ALUMINUM DISC REAR WHEELS
OUTSIDE OF ALL WHEELS TO BE POLISHED WITH "ACCU-SHIELD" PROCESS.
Cab Exterior:
CONVENTIONALTWO-DOOR CAB CONSTRUCTED OF EITHER ALUMINUM OR
GALVANIZED STEEL (STEEL CABS MUST BE UNDERCOATED WITH ZIEBART
PROCESS).
CAB MOUNTED TO CHASSIS UTILIZING RUBBER CAB MOUNTS.
LH AND RH EXTERIOR GRAB HANDLES TO BE EQUIPPED WITH FULL-LENGTH
RUBBER INSERTS.
STATIONARY FULL GRILLE TO ALLOW FOR MOUNTING OF EMERGENCY
EQUIPMENT AT FRONT OF TRUCK.
HOOD MOUNTED AIR INTAKE GRILLE (CHROMED OR BLACK)
FIBERGLASS FORWARD TILTING HOOD
DUAL ELECTRIC HORNS
DOOR LOCKS AND IGNITION SWITCH KEYED THE SAME
REAR LICENSE PLATE MOUNT END OF FRAME
INTEGRAL HEADLIGHT/MARKER ASSEMBLY WITH DAYTIME RUNNING
LIGHTS.
(5) LED MARKER LIGHTS AT TOP OF CAB.
OMIT STOP/TAIL/BACKUP LIGHTS AND PROVIDE WIRING WITH SEPARATE
STOP/TURN WIRES TO 4' BEYOND END OF FRAME
STANDARD FRONT TURN SIGNAL LAMPS
DUAL WEST COAST BRIGHT FINISH HEATED MIRRORS WITH LH AND RH
REMOTE. MIRRORS SHOULD BE AT LEAST 16.5" X 7" AND HAVE BREAKAWAY -
STYLE BRACKETS.
CAB SHOULD ACCOMMODATE A 102" EQUIPMENT WIDTH.
LH AND RH MINIMUM 7" BRIGHT FINISH CONVEX MIRRORS MOUNTED UNDER
PRIMARY MIRRORS
STANDARD SIDE/REAR REFLECTORS
TINTED DOOR GLASS LH AND RH WITH TINTED WING WINDOWS.
RH AND LH ELECTRIC POWERED WINDOWS.
TINTED WINDSHIELD.
WINDSHIELD WASHER RESERVOIR SHOULD HOLD AT LEAST ONE AND ONE
HALF GALLON OF WASHER FLUID.
Cab Interior:
INTERIOR SHOULD BE MANUFACTURERS HIGH LEVEL GREY VINYL.
DELUXE INTERIOR CONVENIENCE PACKAGE.
MOLDED DOOR PANEL WITH UPPER VINYL INSERTS.
FLOOR TO HAVE VINYL MATS WITH INSULATION.
CAB TO BE EQUIPPED WITH FORWARD ROOF MOUNTED CONSOLE WITH
UPPER STORAGE COMPARTMENTS.
DASH SHOULD BE EQUIPPED WITH A STORAGE COMPARTMENT.
STORAGE COMPARTMENTS ALSO IN BOTH LH AND RH DOOR PANELS.
DIGITAL FLUSH MOUNTED CLOCK IN DASH
(2) CUP HOLDERS LH AND RH DASH
DASH PANEL CONTROLS SHOULD ALL BE ACCESSIBLE TO DRIVER.
ADDITIONAL REMOTE PROGRAMMABLE MODULE TO FACILITATE BODY
INSTALLATION.
HEAVY DUTY HEATER, DEFROSTER, AND AIR CONDITIONING SYSTEM.
STANDARD HVAC DUCTING
MAIN HVAC CONTROLS WITH RECIRCULATION SWITCH
HEATER PLUMBING SHOULD HAVE BALL SHUTOFF VALVES.
A/C UNIT TO HAVE TWO HEAVY DUTY AIR CONDITIONER COMPRESSORS
DRIVEN BY SERPENTINE BELT, WITH COOLANT RATED AT R-134A (U.S.
STANDARD).
SILENCER INSULATION PACKAGE FOR CAB.
SOLID-STATE CIRCUIT PROTECTION FOR ELECTRICAL SYSTEM.
12V NEGATIVE GROUND ELECTRICAL SYSTEM.
DOME LIGHTS TO BE ACTIVATED BY BOTH LH AND RH DOORS, WITH DUAL
READING LIGHTS, LOCATED AT CAB ROOF.
LH AND RH ELECTRIC DOOR LOCKS.
(2) 12 VOLT POWER SUPPLY IN DASH.
HIGH BACK AIR SUSPENSION DRIVER SEAT, NFPA COMPLIANT.
HIGH BACK AIR SUSPENSION PASSENGER SEAT, NFPA COMPLIANT.
DUAL DRIVER SEAT ARMRESTS AND PASSENGER SEAT INBOARD ARMREST.
LH AND RH INTEGRAL DOOR PANEL ARMRESTS.
GRAY MORDURA CLOTH DRIVER SEAT COVER.
GRAY MORDURA CLOTH PASSENGER SEAT COVER.
3 POINT HIGH VISIBILITY ORANGE RETRACTOR DRIVER AND PASSENGER
SEAT BELTS.
ADJUSTABLE TILT AND TELESCOPING STEERING COLUMN.
18" (450MM) STEERING WHEEL.
DRIVER AND PASSENGER INTERIOR SUN VISORS.
Instruments & Controls:
INSTRUMENT PANEL TO BE GRAY IN COLOR, OR MANUFACTURER'S
CLOSEST EQUIVALENT. DASH TO BE EQUIPPED WITH THE FOLLOWING:
LOW AIR PRESSURE LIGHT AND BUZZER.
2" PRIMARY AND SECONDARY AIR PRESSURE GAUGES.
DASH MOUNTED AIR RESTRICTION INDICATOR WITH GRADUATIONS.
97 DB BACKUP ALARM.
CRUISE CONTROL WITH SWITCHES ON STEERING WHEEL OR IN DASH.
KEY OPERATED IGNITION SWITCH AND INTEGRAL START POSITION; 4
POSITION OFF/RUN/START/ACCESSORY
ODOMETER/TRIP/HOUR/DIAGNOSTIC/VOLTAGE METERS. ODOMETER MUST
READ TO THE 1/10TH OF A MILE.
DIAGNOSTIC INTERFACE CONNECTOR, 9 PIN, SAE J1587/1708/1939,
LOCATED BELOW DASH
2" ELECTRIC FUEL GAUGE.
PROGRAMMABLE RPM CONTROL - ELECTRONIC ENGINE.
ELECTRICAL ENGINE COOLANT TEMPERATURE GAUGE.
2" TRANSMISSION OIL TEMPERATURE GAUGE.
ENGINE AND TRIP HOUR METERS.
ELECTRIC ENGINE OIL PRESSURE GAUGE.
AM/FM/WB/CD/MP3 PREMIUM RADIO, DASH MOUNTED.
(2) RADIO SPEAKERS IN CAB.
AM/FM ANTENNA.
POWER AND GROUND STUDS IN/UNDER DASH.
ELECTRONIC MPH SPEEDOMETER.
ELECTRONIC 3000 RPM TACHOMETER.
IGNITION SWITCH CONTROLLED ENGINE STOP.
DIGITAL VOLTAGE DISPLAY INTEGRAL WITH DRIVER DISPLAY.
SINGLE ELECTRIC WINDSHIELD WIPER MOTOR WITH DELAY.
MARKER LIGHT SWITCH INTEGRAL WITH HEADLIGHT SWITCH.
ONE VALVE PARKING BRAKE SYSTEM WITH WARNING INDICATOR.
SELF CANCELING TURN SIGNAL SWITCH WITH DIMMER, WASHER/WIPER
AND HAZARD IN HANDLE.
INTEGRAL ELECTRONIC TURN SIGNAL FLASHER WITH HAZARD LAMPS
OVERRIDING STOP LAMPS.
Design:
PAINT: ONE SOLID COLOR
Color:
CAB COLOR A: L2684EB RED (COLOR TO MATCH MOST RECENT PURCHASE)
CHASSIS FRAME PAINT: WHITE POLYURETHANE
Extended Warranty:
CHASSIS WARRANTY TO BE AT LEAST 3 YEARS/36,000 MILES
ENGINE WARRANTY TO BE 5 YRS/200,000 MILES
ALLISON TRANSMISSION WARRANTY, 5 YRS/UNLIMITED MILES
Y N
2.1 OEM AIR RIDE SYSTEM
An OEM air ride system will be on chassis. Manufacturer will install a red, low air
indicator light in the front console and a dump cancel switch by the passenger rear
entry door. The unit will dump with the opening of one of the rear entry doors and
with the OEM dump switch in the dash.
Y_N_
2.3 FUEL SYSTEM CAPACITY
The fuel system capacity shall be a minimum of 50 gallons and shall meet FMVSS
301 "Fuel System Integrity".
Y N
2_A TIRFR
The vehicle shall be equipped with seven (7) wheels and tires. The tires shall be
OEM supplied 245/70R19.5 12-ply load range F steel belted radials as specified in
chassis specification segment.
Y N
2.5 REAR AXLE
The rear axle shall be as specified in the chassis details of this specification. To
ensure patient comfort, assist with vehicle stability, and provide the required loading
height, a rear air suspension with a 12,000-pound capacity shall be used. This
system shall include a 5.3" ride height, an air reservoir, an engine -mounted
compressor, shock absorbers, and dump control.
Y N
2.5.1 ANTI -SWAY CONTROL
A Road Master Brand 1.50" diameter front and rear sway bar (or equal) shall be
provided to assist vehicle stability. This Road Master Brand sway bar shall be
engineered to improve handling characteristics by reducing the body roll and
balancing the weight transfer during cornering.
Y N
2.6 ELECTRIC THROTTLE
The OEM throttle device shall be preset to the proper RPM. Depressing the brake
pedal or shifting into gear shall deactivate it.
2.7 APPOINTMENTS
The manufacturer's heaviest duty heating and air conditioning package must be
used. The vehicle shall be equipped with dual electric multi-speed/delay windshield
wipers and washer mechanism. The seatbelt/shoulder harness mechanisms shall be
encased with a high impact plastic trim housing color keyed to match the driver's
compartment. The balance of the driver's compartment trim shall be accomplished
by the use of Formica, carpet, and cloth backed vinyl trim panels with 3/8" high -
density foam padding (having an R factor of 0.25).
Y xN
2.8 HEADLINER
The cab headliner shall be OEM standard automotive cloth.
Y1CN
2.9 BULKHEAD CAB
The bulkhead cab wall shall be the OEM wall, which matches the dash color
scheme.
YX N
2in SIGN
One (1) "NO SMOKING OXYGEN EQUIPPED" and "FASTEN SEATBELT" sign shall
be installed in the driver's compartment on top of the floor mount console - toward
walk-thru.
2.11 MAP BOX
A map box and three (3) latex glove box holders and trash receptacle shall be
provided and installed on the cab floor, between the driver and passenger seating
positions. It shall be easily accessible by either the driver or passenger. Exact
design shall be the same as the Department's newest ambulances.
2.12 BATTERY SWITCH
A battery switch is to be installed. This system will open the power circuit from the
batteries to the main circuit board and interrupt power to all conversion functions.
2.13 TIRE FILL EXTENSIONS
Dicor stainless steel braided fill extensions shall be provided on both inside and
outside rear tires of the dual rear wheel vehicle.
`Ai[II�,IINZ191zk-
Side mounted rear view mirrors shall be provided with chrome, polished finish. They
shall incorporate both flat and standard convex heads. The primary mirror shall be at
least 16.5" x 7" in dimension, and the convex head at least 8" in dimension. Mirror
assemblies shall attach to the body utilizing breakaway -type brackets. Mirrors shall
be electrically operated and heated.
3.0 VEHICLE WIRING
All insulated cable shall conform to SAE J1292 requirements and shall have type
GXL high temperature thermoplastic insulation conforming to SAE J1127 and J1128.
All wire shall be of a gauge size to carry 125% of the current required by the specific
circuit without overheating. All wires are to be color coded and stamped with the
function of the circuit every four [4] inches for the continuous length of the line.
Where practical or required, all wires shall be routed in high temperature looms with
a rating of 300 degrees Fahrenheit. All conductors shall be annealed copper with
machine crimps. Wiring harnesses shall be assembled and warranted by the vehicle
manufacturer. This system must meet or exceed AMD Standard 005, Ambulance
12-Volt DC Electrical System.
3.1 ALTERNATOR
One (1) internally regulated and internally rectified LN 12-volt 270-amp alternator
shall be supplied. The alternator must be covered by the Leece Neville warranty.
3.2 WIRING MODULE
An angled cabinet forward of the rear facing Technician's seat shall house the main
bank of electrical components. Solenoids, relays, circuit breakers, etc. shall be on
the electrical distribution panel behind a ventilated door measuring approximately 55"
Y N
RIIIIIIIIIII114
Y N
1'111111111111111i,l
Y N
Y N
Y N
high x 18" wide. This door shall hinge on the left side for ease of access for
maintenance and repair and shall have a SouthCo flip -latch to secure it in the closed
position. Adequate ventilation shall be supplied through two (2) polished metal,
louvered vents located near the top and bottom of the door.
Y N
3.3 PORTABLE EQUIPMENT CHARGING CIRCUIT
Two (2) additional 12 VDC circuits for charging portable battery powered devices, i.e.
Suction units, hand lights, defibrillators, portable radios, etc. shall be provided. These
circuits shall prevent discharge of chassis batteries by only permitting the charging of
portable devices when the vehicle is either running or the battery conditioner is
connected to shore power (operational). This implies that a battery conditioner is
required and may be specified in a different location within these detailed
specifications but is not necessarily being specified within this paragraph. A minimum
of 10-amp circuit breaker protection shall be provided for each circuit. These tagged,
identified leads shall be located, one (1) in the patient compartment and one (1) in
the vehicle cab. These leads shall not be connected to power nor shall they have any
connectors attached at either end. These circuits are intended for unspecified future
use. t/
Y ?� N_
3.4 SEQUENCER / LOAD MANAGER
To prevent excessive loading or load spikes on the electrical generating system at
system start up, a sequencer/load manager shall be integrated into the main circuit
board for stepped control of the main master emergency functions. The sequencer
shall sequence ON or OFF all master emergency functions at 0.5 second intervals.
The sequencer/load manager shall sequence specified loads ON, in the following
manner:
1. Body Warning Lights
2. Patient Compartment Dome Lights
3. Patient Compartment HVAC
4. Front Light Bar
5. Intersection and Grille Lights
6. Rear Light Bar- if installed
7. Wig -Wag Headlights- if installed
When a "low voltage" situation is detected, an audible alarm shall sound, and an
indicator light shall illuminate signaling the situation. When the vehicle transmission
is in PARK, the load manager shall shed emergency functions until the system
output voltage and the amperage draw of the systems still in operation equalize.
When in PARK and the vehicle PARK BRAKE is applied, the Stationary Elevated Idle
Control (SEIC) will activate to provide additional voltage for the system. If the "low
voltage", 12.0 volts or lower persists, the sequencer/load manager shall initiate the
load shedding sequence at each 0.2-volt increment in the reverse order of these
emergency functions.
NOTE: Vital medical equipment such as suction aspirator system and/or electric
oxygen valve shall not be included in the load shedding sequence. These systems
shall remain powered until total failure of the electrical generating system occurs.
YK N
3.5 LOW VOLTAGE MONITORING SYSTEM
There shall be installed, as an integral function of the ambulance conversion main
power board, circuitry that continually monitors electrical system voltage. This
system shall activate an audible alarm and a steady burn red LED warning light to
indicate that system voltage has reached or fallen below 11.7 volts. There shall be
included a switch to deactivate the audible alarm. The audible alarm, LED indicator
light and the switch shall be located on an auxiliary control panel located in the
drivers control console below the main switch panel.
3.6 DRIVER SWITCHING CONSOLE
A console shall be built onto the engine cover. At the far right of the console will be
housed the patient code lights and door open indicator lights. The ammeter,
voltmeter, and battery indicator lights shall be located on a separate panel. The
ammeter, depending on equipment/chassis manufacturer specified, shall indicate the
current flow to the batteries or from the alternator. The 12-volt voltmeter shall
indicate the voltage of the batteries. An audible low voltage -warning device shall be
installed with a reset cancel switch. This device shall sound whenever the voltage of
the vehicle drops below 11.8 volts. This device shall automatically reset once the
batteries are above 11.8 volts. An engine hour meter will be located near the bottom
of the console on the driver's side and will be wired to ensure an accurate reading of
running hours. Both the volt and ammeters shall be digital with LED display.
The complete console, manufactured of automotive plastics, shall be free of sharp
edges and molded to match the contours of the engine cover. It shall contain all
emergency switches, module switching, and legends according to their function and
have backlighting controlled by the headlight rheostat. The switches shall be Euro-
style, moisture resistant, rocker type, and shall be UL listed and CSA approved.
Switch terminals shall be 1/4" spade types. The switch legends shall be engraved
plastic inserts. The backlighting shall light the words themselves rather than the
background. Backlighting shall be accomplished with electro-luminescent light strips
for their benefits of consistent light output, low amp draw, and extended service life.
Switch location and configuration to match current SBFD Medic 4.
The console shall contain the following features:
Master
Primary/Secondary
Front Light bar
Backup Alarm Disable
Horn/Siren
Left side Scene Lights
Rear Load Lights
Right side Scene Lights
Module Disconnect
Patient Status Indicator Lights
Patient Door Open Red Light
Compartment Door Open Amber Light
Hour meter
[1 ] Ammeters
Voltmeter
Battery Indicator Lights
Spare Switch
Y N
Additional switches shall be added to the console when specified in this document.
Y N�(
3.7 AUDIBLE ALARM
An audible "Door Open" alarm shall be provided and installed in the driver's console.
It shall warn the driver if any compartment or module entry door on the vehicle is
open or ajar and the vehicle is placed into gear.
Y N
3.8 INTERCOM SYSTEM
A pre -wire shall be done with Department provided cables for a headset intercom
system. This must be verified by SBFD representative prior to installation.
Y N
3.8.1 Two (2) 22-gauge 9 wire cable shall be installed from the forward area of the
overhead squad bench cabinet to under the chassis radio/siren console.
3.9 BATTERIES
There shall be three (3) matching "No Maintenance" 12-volt batteries. They shall
total not less than 2,700 CCA with 180 minutes of reserve capacity. The batteries
shall be located in the OEM location under the driver step, below cab door, in a tray.
Add on step shall not hinder battery access.
A N_
3.10 SEAT BASE INTERNAL 12 VOLT DC POWER
For certain standard internal 12-volt DC power circuits, there shall be circuit
protection provided by the use of manual reset breakers mounted in the outboard
panel of the driver's seat base. Potter & Brumfield 12 VDC breakers shall separately
protect the Radio Power circuit with a 40-amp breaker; the Constant Power circuit
with a 20-amp breaker; the Ford auto -throttle system with a 10-amp breaker; and the
Isolator circuit for the two (2) additional 12 VDC charging circuits required in 21-02-
00, a 20-amp breaker. Due to the potential danger associated with a separate
"battery hot" circuit, no exceptions to the above will be allowed. This Isolator circuit
includes a "low voltage" Schottky Diode to isolate medical equipment batteries from
any electrical loads. The diode shall be located and electrically connected between
the circuit breaker and the receptacles. Additional breakers may be added for
optional equipment such as power door locks, multiple radio installations or
compressor pumps. Additional radio leads including hot wire, ignition switched hot
wire and ground shall be provided. One set shall be in the front console and one set
in the rear action area. Each power lead shall have a 30-amp circuit breaker and
include one 12-volt hotwire and fuse holder with 30 amp.
3.11 POWER OUTLETS
Two (2) 12-volt power point style outlets shall be installed. One (1) shall be provided
in the forward section of the primary action area, above the countertop and one (1) in
the upper section of the ALS cabinet.
YKN_
3.12 115 VOLT AC POWER
There shall be 115-volt AC wiring furnished. A three -wire system is used for
powering medical equipment, battery charger, etc. This electrical system, including
wiring and associated equipment, shall comply with AMD STD 009, 120V AC
Electrical Systems. The system shall incorporate a hospital grade GFI (Ground Fault
Interrupt) device with a 20-amp circuit breaker that can also be used as a disconnect
switch for the interior 115-volt outlets. The GFI device shall be located on the street
side in the action area. When an inverter is specified, an automatic transfer switch
shall be furnished which will automatically turn off the inverter 115-volt supply when
the 115-volt utility shoreline power is applied.
YkN
3.13 INVERTER
A Vanner, model #20-1050CUL inverter shall be provided and installed. The Vanner
20-1050CUL/CULW AC Power System shall combine a powerful DC to AC power
inverter with an automatic battery charger/conditioner and a 30-amp AC transfer
switch. When connected to shore power (AC utility power) the vehicle's battery is
charged, than automatically maintained in full charge condition. The shore power
shall be automatically connected to the system's AC output receptacle to supply
power to the AC loads. When shore power is disconnected, (vehicle underway) the
automatic transfer switch shall connect the AC output receptacle to the power
inverter, which obtains power from the 12 volt battery.
The 20-1050CUL/CULW system shall contain a front panel LED indicator status
panel and interface connector for the remote monitor/control unit. The inverter shall
be mounted in the lower forward corner of the D2 compartment.
011111111111!J
3.14 EXTERIOR SHORE POWER
There shall be a Kussmaul 115 volt "Auto -Eject" plug rated at 20 amps or more with
a spring -loaded cover assembly, UL listed for exterior use, located on the left side of
the ambulance body close to the driver's door. The plug shall be equipped with a
Dynamic Disconnect Switch. This shall energize the vehicle's 115-volt AC circuit
from an exterior power source. This connector must be labeled: "l 15-volt AC, 60 Hz,
20-amp power supply".
Y N
3.15 INTERIOR 115 VOLT AC OUTLETS
There shall be three (3) three -wire duplex 115-volt AC hospital grade receptacles.
There shall be one [1] in the primary action area, one [1] in the second action area
and one [1] in the AILS cabinet. There shall be red indicator lights located within
each 115-volt outlet to indicate a live "hot" circuit. Add -on style indicators are not
acceptable. The receptacles shall be clearly labeled: "115 VAC".
YX_N
3.15.1 Two (2) additional three -wire duplex 115-volt AC hospital grade receptacles
shall also be provided and installed. The one (1) shall be located over the squad
bench and one (1) in the lower ALS cabinet. There shall be red indicator lights
located within the 115-volt outlet to indicate a live "hot" circuit. It shall be clearly
labeled: "115 VAC".
YY—N_
3.16 ELECTRICAL EQUIPMENT
All electrical equipment shall be electromagnetic radiation suppressed, filtered, or
shielded to prevent interference with radio and telemetry equipment. The RFI shall
not exceed SAE J551 limits.
Y�N_
3.17 SPOTLIGHT
There shall be one (1) Optronics "Blue Eye 4000" hand-held spotlight (400,000-
candle power) hardwired and located behind the driver seat. The spotlight must be
weatherproof, corrosion and chip resistant, have a non -glare "Blue Eye" bulb, and
have a momentary "on" switch. A hanger shall be supplied for the spotlight.
Y�N
4.0 SIREN
A Federal, model #PA300MSC siren with microphone shall be provided. It shall
include wail, yelp, air horn, Hi-Lo tone, user selectable switching for horn ring tap and
press/hold, manual horn/siren and radio rebroadcast. Fused circuit failure protection,
front panel public address volume control and built-in noise canceling microphone
are also included.
Y N
4.1 SPEAKERS
A CPI #SA4311 D speaker shall be securely bolted through the chassis OEM front
bumper on the driver's side.
A CPI #SA4311 P speaker shall be securely bolted through the chassis OEM front
bumper on the passenger's side.
Y N
4.2 AIR HORNS
Two (2) Grover Stutter tone non-adjustable air horns shall be provided and installed
on the hood. The air horns shall be powered by the chassis OEM compressor & air
reservoir. A check valve shall be installed between the air horns and the air reservoir
to prevent depletion of air reservoir.
Y_CN
4.2.1 A foot pedal switch shall be provided on the outboard, vertical surface of the
floor on the passenger's side of the cab. It shall activate the air horns. Labeled
"AIR HORN"
YJ— N
4.2.2 A lanyard shall be provided in the center of the headliner of the cab. It shall
activate the air horns.
Y N
4.3 BACKUP ALARM
A Preco, Model #230 backup alarm (or equal) shall be installed on a 2" x 2" floor tube
at the rear of the ambulance. This alarm shall activate whenever the ambulance is
put into reverse gear. There shall be a momentary switch in the driver's switch
console that will cancel the alarm. The system shall have an automatic reset to
activate the alarm the next time the vehicle is placed into reverse. When activated,
this alarm shall generate an intermittent warning tone at a minimum of 97 dB as
prescribed by KKK-A-1822F.
5.0 EXTERIOR LIGHTING
Exterior lighting shall conform to FMVSS 108 and consist of halogen headlights, ICC
clearance lights with chrome brush guards, parking lights, hazard warning lights,
license plate lights, tail, stop, and backup lights. Tail and stoplights shall have red,
clear, and amber lenses. Electrical wires for the taillights shall be sealed to protect
them from the elements of weather. There shall also be two (2) side body rear lights
with red lenses that flash with turn signals and steady burn with the DOT lights.
There shall be, included with the bid, evidence from the lighting manufacturer that all
specified warning lights meet the photometric and chromaticity requirements of the
current version of KKK-A-1822 as certified by a third -party testing entity.
5.0.1 Eleven (11) Whelan OS series ICC/DOT lights shall be provided and installed
on the upper ambulance module body. Each light shall be LED type with a protective
chrome bezel. Two (2) each shall be installed on the side upper body corner
extrusion area. Five (5) shall be installed on the rear and (2) shall be installed on the
front upper body corner extrusion area.
5.1 STOP, TAIL, TURN AND BACK-UP LIGHTS
Tail and stoplights shall be Whelen 600 Series LED, red and the backup lights shall
be Whelen 600 Series LED clear lights with integral Whelen flanges. All LEDs and
the electrical wires for the taillights and turn indicators shall be sealed and or
encapsulated to protect them from the elements of weather. Turn lights shall be
Whelen 600 Series LED amber arrow turns with integral Whelen flanges. The
tail/stoplights turn arrows and back-up shall be mounted vertically on the rear module
body.
5.2 FRONT WARNING LIGHTS
An ETM "Traffic Mover Pulse" headlight flasher shall be provided. The flasher shall
produce 3.6 flashes per second.
5.2.1 Two (2) Whelen 700 Series red Super LED lights, each with a Cast Products,
Inc. bezel shall be provided in the front grille area, each with a clear lens.
5.2.2 Two (2) Whelen 400 Series red Linear12 Super LED intersector lights, each
with a clear lens and flange shall be provided.
Y N
Y N
Y N
0IIIIIIIIIIIIJ`v
Y N
YN_
5.2.3 Seven (7) Whelen 900 Super LED front body light with an integral 9E flange
shall be provided and mounted evenly across the top of the front body. The lens
colors shall be clear with the LED colors from left to right: red, clear, red, clear, red,
clear, red.
Y RCN
5.2.4 There shall also be two (2) Whelen 600 Series LED side turn body lights, one
(1) mounted each upper corner of the front of the body, with amber lenses and
arrows that flash with turn signals.
Y X N
5.3 SIDE BODY LIGHTS
Four (4) Whelen 900 Series red Super LED side body lights with an integral 9E
flange shall be provided and mounted one (1) in each upper corner on both sides of
the body. The lens colors shall be clear on both the street side and curbside light
sets.
YIXN
5.3.1 There shall also be two (2) Whelen 700 Series Red LED side body rear lights
with red lenses and integral flanges that flash with turn signals and steady burn with
the DOT lights.
YXC N
5.3.2 Two (2) Whelen 700 Series red Super LED lights, each with an integral 7E
flange and a clear lens shall be provided and mounted one (1) directly above each
rear wheel well.
Y N
5.4 SCENE LIGHTS
There shall be three (3) Whelen 24 LED 900 Series 8-32-degree scene light installed
on each side of the body. Each scene light shall have a .clear lens with directional
LEDs to cast downward illumination. Each side shall be independently lighted and
switched separately in the driver's switch console. The lights shall be a minimum of
75" above the ground and not obstructed by open doors.
The scene lights shall meet the current AMD Standard 024- Scene Light
Performance.
Y N
5.4.1 The two (2) curbside scene lights shall activate when the side entry door is
opened and the (2) rearmost scene lights shall activate when the vehicle is placed in
reverse.
5.5 REAR BODY LIGHTS
Three (3) Whelen 900 Series Super LED lights with clear lenses shall be installed.
Two (2) shall be red Super -LEDs, model 90RR5SRR, surface mounted on the upper
rear module body corners. One (1) shall be an amber Super -LED, model 90AA5SAA,
surface mounted on the upper rear module body center.
goot�'m
5.6 LOAD LIGHTS
Two (2) Whelen 900 Series model #9SCOENZR Opti-Scene 8-32-degree LED load lights with
flanges shall be located above the rear doors. Each light shall have an inner lens giving a
downward cast to the light beam and activate when the rear doors are opened or the vehicle
is placed in reverse gear. There shall also be a switch on the driver's console to activate the
rear load lights when the doors are closed. The lights shall be a minimum of 75" above the
ground and not obstructed by open doors.
YXN
5.7 RUBRAIL LIGHTS
Six (6) Whelen LED Strip-Lite lights shall be provided and mounted in the C-Channel
rub rails. One (1) red in each forward and rearward corner and one (1) white center
shall be provided on both sides of the body. The side entry door C-Channel rub rail
light shall activate to steady burn with opening of the side entry door. These Lights
shall be installed in the C-channel rub rail to provide protection for this warning light.
Due to this being a high wear area of the vehicle, installation of the lights above or
below the rub rail are more exposed to damage and unacceptable
Y�CN
5.8 WARNING LIGHT FLASH REQUIREMENTS
Within the flash pattern established for each light or light group by KKK-A-1822F,
each emergency light shall flash on/off 75 to 125 times per minute. Each light shall
have a minimum of 20 square inches of illuminated viewing area. The flash pattern
for the warning lights on this vehicle shall be as described in KKK-A-1822F, Section
3.8.2.1, Table 1. Compliance with this specification shall not be compromised in
order to maintain a high level of conspicuity for 360-degrees around the vehicle.
Oft,
5.9 PARK OVERRIDE WITH AUTOMATIC RESET CANCEL SWITCH
All forward facing clear lights shall be shut off when the vehicle is placed into park or
neutral. An override switch shall be provided in the front switch console.
Y_�,N
5.9.1 BRAKE OVERRIDE
Two [2] rear mid -height lights shall be wired to brakes. The brakes shall override the
flashers.
Y_N
6.0 CONSTRUCTION CHARACTERISTICS
The body shall be 170" long and 93.5" high. All body panels, structures, and
extrusions shall be fabricated of aluminum using alloys consistent with the load
requirements of the vehicle. Unitized body construction will be accomplished by MIG
welding all sheets, radius extrusions, corners, structural members together. All body
surface aluminum side panels and roof panels shall be intermittently Heli arc welded
to the body frame support members in such a manner as to provide maximum
strength and durability without causing heat warp. All exterior metal -to -metal body
seams or the area of attachment of one aluminum panel to another shall be Heli arc
welded. All such welds shall be ground smooth for proper paint adhesion and
appearance. The body structure shall be built and warranted by the vehicle
manufacturer. The vehicle must additionally meet or exceed AMD Standard 001,
Static Load Test for Ambulance Body Structure.
Y N
6.1 CERTIFIED WELDING PERSONNEL
To assure that the specified vehicle meets the letter, as well as the intent of the
Specification, the welding of body structure, chassis attachment points, doors, any
aluminum or stainless steel components or attachments shall be performed by or
directly supervised by personnel Certified by the American Standard Welding
Association (ASWA). Those individuals shall have proof of current certification and
shall make such proof available to the department upon reasonable demand.
Y N
6.2 CORNER EXTRUSIONS
To ensure weight support and structure durability in the event of an accident or
impact the utmost strength in corner posts must be used. A radius arched aluminum
extrusion is required. The extrusion shall include a full-length reinforcing member
that extends from the crest of the curvature to the focal point of the outer arch. The
continuous gusset must be extruded into the corner radius. Corner posts that are a
part of the exterior body skin are not recommended as they may pull away at the
point of impact. The extrusions must have a minimum strength of 29,000 psi.
Y4_N
6.3 ROOF
The roof shall be constructed of one-piece .090" aluminum. This aluminum shall be
a highly corrosion resistant alloy and a tensile strength range of 28,000 to 33,000 psi.
The roof substructure shall be constructed of four (4) full-length "Z" sections MIG
welded to the roof for support. The "Z" sections shall be a series of six (6) separate
pieces running full length, front to back, bridging to the roof bow framework. They
shall be of equally spaced distance, inboard to outboard, stair stepped sizes of 3/4" x
1-1/2" x 3/4" inboard, 3/4" x 1-1/4" x 3/4" center, and 3/4" x 1" x 3/4" outboard to form
a crowned roof facilitating water runoff and ice build-up. The roof shall then be
reinforced the entire length of the unit. For this reason, flat roofs shall be considered
unacceptable. There shall be in addition to the above supports, twelve (12) .125" x
2" x 2" cross members welded to the "Z" sections 12" on center and be made of a
highly corrosion resistant alloy with a tensile strength range of 31,000 to 35,000 psi.
Aluminum plates shall be welded between the roof support channels to mount
lighting fixtures, assist rails, hanging stretcher mounts, and IV holders. Corner
gussets shall be Heli arc welded to the roof radius extrusions to enhance roof load
bearing characteristics. Horizontal corner extrusions shall be .125" thickness and 2-
1/2" radius. There shall be an integral drip rail formed into the extrusion. The
horizontal extrusions shall use an interlocking method to secure the roof sheet into
the envelope of the extrusion. The horizontal extrusions shall be of an open -face
design for insertion of 2" x 2" x .125" tube structural members. Corner caps shall be
.125" cast aluminum and welded in place.
YN
6.4 SIDES
The sides shall be constructed of .125" aluminum sheets with a highly corrosion
resistant alloy and a tensile strength range of 28,000 to 33,000 psi. The body shall
have straight sides free of waves and welding warpage. Doorjambs shall be formed
integral into the sidewall .125" aluminum sheets (extruded doorframes are not
acceptable). Each sidewall shall have twelve (12) vertical .125" x 2" x 2" wall studs
12" on center and joined to the roof supports. The box 2" x 2" channels shall be a
highly corrosion resistant alloy with a tensile strength range of 31,000 to 35,000 psi.
All box 2" x 2" roof and side support bows are .125" aluminum. Vertical corner
extrusions shall be .125" thickness and have a 2-1/2" radius. The radius ends shall
be tapered. The vertical extrusions shall be slotted for insertion of the sidewall
sheets. The vertical extrusions shall be of a web construction design for internal
structural support. The complete roof and sidewall structure shall be treated with a
sound -deadening barrier of BUNA Rubber.
A continuous 8" x 2" side impact beam shall be welded to side body and sidewall
extrusions to each side of the unit where the squad bench and CPR seats are
located. This side impact beam shall allow for secure and customizable mounting
points for the squad bench and CPR seat seatbelts. The side impact beam shall
also provide additional structure and rigidity in these seating locations in the event of
an accident. This side impact beam shall be constructed of minimum 8" x 2" x .250"
thick aluminum. Seat belt backer plates welded or adhered in between the extrusions
are unacceptable to this agency as this does not displace the energy of a side impact
as effectively as a continuous side impact rail.
0MMW'W
Y N
6.4.1 DROP SKIRT
A 6" drop skirt shall be incorporated into the curbside, forward of the rear wheels of
the module body to provide additional protection, lower the side entry doorstep well
and an aesthetically pleasing appearance to the completed ambulance. j�
Y/1 N
6.5 FLOOR
The body floor shall have a tubular frame structure with main members constructed
of .125" x 2" x 2" and .125" x 1" x 2" aluminum tubes, all being fully welded and
gusseted. This framework is mounted using rubber gaskets to prevent contact of
dissimilar metals. The tubular framing shall be on average of 12" on center. 3/4"
thick x 6" wide aluminum shall be welded on top of the cushion rubber mounts
installed full length of the body. This is necessary to add additional strength, ease in
mounting, and ease in remounting the body later. There shall be plates welded into
the floor structure to provide additional mounting support for the cot mounts and
technician seat. The floor frame is then plated the entire length with a .090"
aluminum moisture barrier mounted under the sub -floor to act as a heat shield and
vapor barrier. The sub -floor is then sealed and fastened to the floor structure.
6.6 DRIVE SHAFT GUARD
A square tube steel drive shaft loop or guard shall be installed just behind front U
joint. This is designed to prevent the driveshaft from creating a dangerous situation
such as hitting the ground or whipping in the event of a universal joint failure.
6.7 COMPARTMENT & ENTRY DOOR CONSTRUCTION
All exterior compartment and entry doors shall be constructed of a single piece of
.125 sheet aluminum. The use of extrusions for doorjambs or doorjambs is not
allowed. The door profile shall be a double pan form of 2.75" total thickness. Each
door shall have the seal installed on the outer door pan flange to assure maximum
sealing surface and to protect the rotary latching mechanism from environmental
influences. Access for maintenance to the latching mechanism shall be through 2.0"
mounting holes located in the upper and lower outboard edges of the inner door pan
panel. These access holes shall be covered by a reflective device mounted to a
rubber grommet cap. The inner door pan flange shall be formed to provide a recess
in which the inner door liner panel is seated. Inner door liner panels shall be affixed
to the flange with stainless steel, serrated spring washers and TX -25 Type F Torx-
head machine screws. Each door shall be insulated with not less than 2.0" of spray
foam. The insulation must be configured to prevent contact with or the fouling of the
coated steel latch connecting rods. The interior door pan of each exterior door shall
be stamped with a unique alphanumeric code denoting the specific size of that door.
This code shall assure the quick and exact replacement of a damaged door.
6.8 EXTERIOR COMPARTMENT DEPTH
All exterior compartments shall have a clear depth of approximately 20.75".
6.91NSULATION-REFLECTIX-SIDES/CEILING/SPRAYFOAM- FLOOR/STEPWELL
1'�i•
BE==
Y N
Prior to installation of the insulation the entire interior body surface will be sprayed
with a heavy protective coating of sprayable latex rubber to provide sound deadening
and corrosion protection. The body sides and ceiling shall have 2" Reflectix dual air
bubble core insulation (or equal) in the walls and ceiling providing an insulation factor
of R-11. The insulation shall be fire retardant, non -settling, non-hydroscopic, and
mildew and vermin proof. The module shall have an expandable polyurethane spray
foam type in the floor and sides and bottom of the step well of the patient
compartment to provide maximum protection from changes in outside temperature.
The insulation shall be fire retardant, non -settling, non-hydroscopic, and mildew and
vermin proof. There shall be a generous amount of undercoating applied throughout
the undercarriage of the body and chassis. Undercoating must be applied according
to chassis manufacturer guidelines.
Y N
6.10 HEAT SHIELDS
To further insulate and protect the patient compartment the ambulance manufacturer
shall install 18-gauge galvanized steel below the sub -floor material to act as a heat
shield and vapor barrier. An .18-gauge galvanized steel sheet, with waterproof
insulation laminated to it shall be installed directly to the bottom of the floor tubes.
This will create a sandwich style construction to further insulate the patient floor in
the area of the muffler and exhaust system.
6.11 FENDER INSULATOR
An additional insulator shall be provided and installed on top of the wheel well liner.
This layered rubber and aluminum foil material shall diminish the effects of noise
created by road debris and provide additional thermal insulation for the patient
compartment.
Y N
6.12 CAB CONNECTION
The vehicle cab back shall be removed without disturbing the structural integrity. A
reinforcement structure shall be fabricated from 16-gauge steel 1" x 1" box tube and
shall be fully welded to the vehicle cab and used as a mounting system to attach the
cab/module expanding bellows.
Y N
6.13 MOUNTING
An Isomount technique shall be used to mount the ambulance body to the chassis
frame. Mounting hardware shall consist of .75" x 6" aluminum bar stock body plates,
ten (16) 7/16"-14 UNC threaded Grade 8 bolts, paired rubber isolators with steel cap,
collared mounting nut for each mounting point and (10) 1/4" steel outriggers with (2)
support gussets using grade 8 bolts. The bolts and rubber isolators are similar to the
type used to mount the vehicle cab. Mounting holes in the top of the outrigger shall
accommodate the mounting hardware. The .75" x 6" aluminum bar stock mounting
plates shall be bolted through the upper mounting isolator with the OEM Grade 8
bolt. The bolt passes through and secures the second isolator below the outrigger
flange with the collared nut. Body sub floor cross members shall be welded to the
aluminum bar stock mounting plates. This combination of components provides the
body with a cushioned ride and allows the body and frame to flex independently to
avoid frame stress.
Y4N_
6.14 LEFT SIDE COMPARTMENTATION
6.14.1 FORWARD OF REAR WHEEL WELL - D1 AND D2
A full height compartment shall be provided in the forward position ahead of the
wheel well. It shall have approximate exterior dimensions of:
26" wide x 84" high
YXN
6.14.2 The D1 compartment shall have a solid, flush mounted, vertically hinged door,
constructed of aluminum.
Y_)'\ N
6.14.3 A low compartment (D2) shall be provided in the rearward position ahead of
the wheel well. It shall have approximate exterior dimensions of:
43" wide x 33" high.
Y N
6.14.4 The D2 compartment shall have double solid, flush mounted, vertically hinged
doors. Each door shall be constructed of aluminum.
Y N
6.14.5 REAR OF WHEEL WELL - D4
A compartment shall be provided in the area rearward of the rear wheel well. It shall
have the approximate dimensions as follows:
43" wide x 45" high
Y-N_
6.14.6 The D4 compartment shall have double solid, flush mounted, vertically hinged
doors. Each door shall be constructed of aluminum.
Y'�LN
14.7 RIGHT SIDE COMPARTMENTATION
There shall be no P1 or ALS exterior compartment door provided. Access for the
ALS cabinet shall be from the interior only.
Y N
6.15 SIDE ENTRY DOOR
The entry/egress door shall be constructed of .125" aluminum sheet box formed with
a 1-7/8" return bend supporting the .090" 3003 alloy aluminum diamond plate inner
liner. Extruded doors and/or doorframes are not acceptable. In addition, for
maximum rigidity, 1-1/2" "C" channel bracing shall be added internally for additional
door structural integrity.
The door shall have a FMVSS approved Tri-Mark rotary latch with a Tri-Mark locking
handle and shall have a two -point rotary latch with adjustable Nader pins located on
the side of the door. It shall also be equipped with a spring assisted two -directional
cam -over door check. The door shall provide a clear opening of at least 32" wide
and 74" high. When opened, the door shall activate the interior dome lights. Each
access door is to be stamped with an alphanumeric code; this will enable the exact
replacement of a damaged door.
6.16 STEPWELL
The patient compartment access door shall have a full aluminum diamond plate step
well. The step well must have a full 18"deep step which allows for easy entry and
egress, a 9" high riser and be 32" wide to match the width of the side entry patient
compartment door. The step well shall be formed entirely from fire grade aluminum
diamond plate which is fully seam -welded into the body at the step well area.
6.17 SIDE ENTRY DOORSTEP
Y N
Y Y,N
A double step shall be constructed of aluminum diamond plate and shall be reinforced.
It will be at least 32" wide and shall allow easy entry and egress.
YX N
6.18 DOOR TRIM
The door shall have a .090" aluminum panel covering the upper and lower door and
full width door panel with .028" Formica, with color to match interior and shall be
impervious to moisture, easily cleaned, durable, and attractive. The middle and
lower portion shall be stainless steel and removable for ease of maintenance.
1'11111111111101
6.18.1 GLOVEBOX
Three (3) glove boxes shall be provided directly above the side entry/egress door. It
shall have approximate dimensions of 20" wide x 9" high and shall have three (3) flip -
up Plexiglas doors with non -locking catches for easy access.
MM"
6.19 STEPWELL LIGHT
Two (2) LED lights shall be provided for the curb sidestep well. The lights shall be
mounted on an angled bracket one (1) over each step and shall activate with the
opening of the side entry door.
Y N
6.19.1 The side entry/egress entrance door shall have a 1.5" diameter polished
stainless steel 90-degree ergonomic style assist handle.
Y N
6.20 REAR OF WHEELWELL — P5
A full height compartment (P5) shall be provided in the rearward area behind the rear
wheel well. It shall have the approximate dimensions as follows:
21" wide x 84" high
YXN_
6.20.1 The P5 compartment shall have a solid, flush mounted, vertically hinged door,
constructed of aluminum.
Y-)_"_
6.21 REAR PATIENT ENTRY DOORS
Each patient entrance door shall be constructed of .125" aluminum sheet box formed
with a double return bend of 2.75" total thickness. Extruded doors and/or
doorframes are not acceptable. Each door shall have the seal installed on the outer
door pan flange to assure maximum sealing surface and to protect the rotary latching
mechanism from environmental influences. The inner door pan liner shall be affixed
to the flange with stainless steel serrated spring washers and TX-25 Type F Torx-
head machine screws. In addition, "C" channel bracing shall be added internally for
additional door structural integrity.
Both rear patient entrance doors shall have an FMVSS 206 tested Tri-Mark locking
handles keyed alike to the side entrance door and a Tri-Mark non -locking handle.
Each rear door shall have a two -point rotary latch with adjustable .50" Nader pins
with head flanges at the top and bottom with release handles on the interior faces of
the doors. When opened, the rear doors shall provide an opening of at least 63"
high and 54" wide. Each rear door shall be equipped with a Cast Products "grabber"
style door check, which shall be located at the bottom of the door. When opened,
the rear doors shall activate the interior dome lights and the rear exterior load lights.
Each access door is to be stamped with an alphanumeric code; this will enable the
quick and exact replacement of a damaged door.
YXN_
6.22 DOOR TRIM
The door shall have a .090" aluminum panel covering the upper and lower door and
full width door panel with .028" Formica, with color to match interior and shall be
impervious to moisture, easily cleaned, durable, and attractive. The middle portion
shall be stainless steel and removable for ease of maintenance.
YkN
6.22.1 Each rear patient entrance door shall have a 1.5" diameter polished stainless
steel 90-degree ergonomic style assist handle.
Y_KN
6.23 REAR BODY CLOCK
One (1) MFS-121 Digital Atomic Clock (or equal) shall be provided directly above the
rear patient entrance doors, recessed into the center of the rear head pad. It shall
be wired directly to the vehicle electrical system.
Y�N_
6.24 SLIDING WINDOW
The entry/egress door shall be provided with a Cleer Vision Brand 20" wide x 19"
high horizontally sliding window. It shall have tempered automotive privacy safety
glass and shall have a locking mechanism to keep the window panels in the desired
position. A screen shall be provided, to prevent airborne particles from entering the
vehicle, when the window panels are in the open position.
Y N
6.25 FIXED WINDOWS
The rear patient entry doors shall each be provided with a Cleer Vision Brand 20"
wide x 19" high fixed window panel. Each window shall have tempered automotive
privacy safety glass.
6.26 SIDE BODY WINDOW Y�C N
A fixed, privacy automotive glass window shall be provided a Cleer Vision Brand in
the right body side, above the rear wheel well in the upper body side. It shall be
approximately 36" wide x 18" high. Y l� X
N
6.27 POCKET WHITEBOARD
A pocketed privacy slide shall be provided on the curbside wall. It shall be
incorporated into the side body window and shall slide into the wall rearward of the
window. When in use, the writing board shall cover the window. There will be a pad
covering the rear end of the privacy slide frame that the writing board will slide
behind.
Y_NX_
7.0 EXTERIOR COMPARTMENT FABRICATION
All exterior compartments, excluding backboard compartments, shall be constructed
of .100" aluminum diamond plate walls and ceilings with .125" smooth aluminum
floors, formed and Heli arc welded. Exterior compartments are welded to both the
inside wall vertical structure and floor structure components for strength and
durability. Each floor shall be "sweep out" design.
YX—N_
7.0.1 All exterior compartment doors shall be equipped with a gas charged hold open
door check.
Y4X—N_
7.1 EXTERIOR COMPARTMENT DOORS
Each exterior compartment door shall be constructed of .125" aluminum sheet
double pan formed with a 1.5"' return bend with recessed offset supporting the .063"
3003 alloy aluminum diamond plate interior liner. Extruded doors and/or doorframes
are not acceptable. In addition, for maximum rigidity, 2.375" "C" channel bracing
shall be added internally for additional door structural integrity. The exterior face of
the door and the door edges shall be formed from one [1] sheet of aluminum. All
doors shall be flush with the body side and shall be fully insulated with polyurethane
spray foam. When opened, the doors will activate their respective compartment
lights. All compartment doors shall be keyed alike. Each access door is to be
stamped with an alphanumeric code; this will enable the quick and exact
replacement of a damaged door. The inner door panels shall be affixed to the flange
with stainless steel serrated spring washers and TX-25 Type F Torx-head machine
screws.
Y N
7.2 EXTERIOR COMPARTMENT DOOR HANDLES AND LATCHING
Door hinges shall be full length stainless steel #304-213 buffed and polished with a
1/4" stainless pin and shall be fastened to the door and door frame with self-locking
stainless -steel screws. Hinges are to be of a slotted style with a round hole on each
leaf of the hinge for permanent lifetime adjustment of the doors. Hinges shall be
staked, not welded, every 4" to prevent pin from moving. The locking mechanism
shall be a Tri-Mark #13136 outside handle, #13028 inside handle with a #12765-01
gasket for the external handle with #14229-01 and #14230-01 rotary latch and
#10355U adjustable Nader pin. Latches shall be near flush with the door skin. Each
latch must be capable of being locked independently with an integral exterior key
lock and a key matching the locks on the curbside and rear entry doors. The latch
system is to be activated by the use of a .156" zinc plated steel rod with a single
point threaded adjustment mechanism. Systems operated by cables are
unacceptable due to the tendency of cable to stretch or fatigue prematurely. The
latch and the Nader pin shall be mounted so as not to interrupt the continuous door
seal. A .437" hole shall be drilled into the edge of each door adjacent to the paddle
handle. This lubrication access shall be sealed with a removable plastic cap for
protection of the internal mechanism.
7.3 EXTERIOR OXYGEN COMPARTMENT VENT
One (1) #1031 Cast Products, polished aluminum exterior oxygen compartment vent
(or equal) shall be provided and installed on the door of the exterior compartment
that houses the oxygen tank retention system. The vent hole shall be 3" in diameter
and provide adequate ventilation for gaseous oxygen should a leak occur. A black
plastic vent shall be provided and installed on the interior door liner covering the vent
Y_Nk
hole to protect it from intrusion by the elements when the door is open.
Y CN
7.4 DRI-DECK
The floor and shelf of each exterior compartment shall be covered with Dri-Deck (or
equal) material that shall be black in color with a safety yellow tapered edge for the
outer edge of each compartment floor.
YXN
7.5 DOOR GRABBERS
A set of door Cast Products "Grabbers" (or equal) shall be provided at the bottom of
the rear doors. They shall be fastened to the door and door frame with self-locking
stainless -steel screws. �(
Y! \ N
7.6 DOOR SEALS
For optimum fit and closure, the compartment and patient entry doors shall close on
a .625" W x .400" thick automotive, closed cell EDPM rubber gasket adhered to first
interior surface of the double pan -formed compartment doors. The gasket seal shall
be located on this surface to prevent exposure of the rotary latch mechanism to
water or dirt when the door is closed.
Ism
7.8 POWER DOOR LOCK SYSTEM -ALL PATIENT AND COMPARTMENT DOORS
The rear patient entry doors and side entry/egress door, along with all exterior
compartment doors and exterior AILS door, shall be equipped with a power locks.
7.9 POWER DOOR LOCK SWITCHES
One (1) exterior power door lock switch with a rubber weather boot shall be provided
and installed in rear license plate bezel hidden from obvious view. It shall be in
addition to the switch installed in the cab to control the power door locks installed on
designated compartment doors.
YKN
7.9.1 Two (2) additional power door lock switches shall be provided and installed in
the patient compartment. One (1) shall be at the curbside entry door and one (1) at
the rear entry doors.
Y N
7.10 POWER DOOR LOCK ACTIVATION
The patient compartment door locks shall be wired to the chassis power door locks.
7.11 STAINLESS STEEL DOOR SILL PROTECTION
There shall be a 20 ga. formed stainless steel compartment doorsill protection for all
exterior compartments. The stainless protector shall be affixed with heavy-duty
double -sided tape to the top surface of the doorsill and extend over the radius edge.
YKN
7.12 COMPARTMENT ILLUMINATION
Each exterior compartment shall be illuminated with 4.25" round, Liteco incandescent
lights Model #69000200 (or equal). These lights shall have clear Lexan lenses and
be recessed into the compartment sides and/or ceiling above and below any
specified shelves. Each door shall have an individual automatic switch to signal a
"door or compartment open" condition and to turn on interior lighting when the door is
opened. The switches shall be Sentrol heavy duty, magnetic reed switches mounted
in the doorframe header interior to the protective door seal.
Y N
7.13 OXYGEN TANK MOUNT
One fully adjustable oxygen tank mount shall be installed in the exterior compartment
D1. This mount shall accommodate an "M" type oxygen tank. This- oxygen tank
retention system must meet or exceed AMD Standard 003, Oxygen Retention
System.
AN
7.13.1 One (1) fixed shelf shall be provided in the D1 compartment located above the
oxygen tank.
YXN
7.13.2 Two (2) Model # 166AH Gear Hooks shall be mounted one (1) on the forward
wall and one (1) on the rear wall of the D1 compartment. Exact hook placement
shall be determined at the pre -build meeting. YY
Y!\ N_
7.14 ADJUSTABLE SHELVES
One (1) adjustable shelf will be provided and installed in the D-2 compartment. Each
shall be easily adjusted to accommodate equipment/supply requirements.
Y N
7.14.1 Two (2) adjustable shelves shall be provided in the D4 compartment. They
shall be easily adjusted to accommodate equipment/supply requirements.
rNIIIIIIIIJ`u
7.14.2 One (1) adjustable shelf shall be provided in P-5 compartment fore of the
back board divider.
Y N
7.15 BACKBOARD DIVIDER
One (1) vertical, 55" x 17.5"x .125" smooth aluminum backboard divider shall be
through the inboard wall of Compartment P-5. It shall be positioned vertically 10"
forward of the rear wall. To provide protection for the equipment retained in the
compartment, the divider shall be Line-X coated.
Y N
7.16 SCBA MOUNTING PLATE
The mounting plate shall be 24" high and run the full width of the compartment. The
mounting plate shall be made of 3/16" smooth aluminum with rolled top and edges
and have a 3/4" lip. There shall be a 1" x 2" aluminum tube welded to the back of the
SCBA plate and mounted to the lower rear wall of the D4 compartment.
Y N
7.17 EQUIPMENT RETAINERS
Three (3) seatbelt style retainer straps shall be provided and installed in the P5
exterior compartment. One (1) shall be located in the aft section 40" from the floor
and two (2) located in the fore section 17" and 54" from the floor.
Y ,N_
7.17.1 A slide out stair chair holder for a Stryker model # 6252 stair chair shall be provided in the aft
section of the P5 compartment under the adjustable shelf. The holder shall be constructed of .125"
smooth aluminum with the entire holder covered with black Line-X bed -liner type material. The back shall
be 38" high, the front shall be at a slight outward angle and be 27" high. It shall be 22" wide and 9" deep.
Dimensions shall allow for easy removal of device from holder.
A seat belt style retaining strap shall be secured to the back with footman loops. The stair chair holder
shall be mounted into the compartment with two (2) 300 lbs., full extension ball bearing drawer sli es.
YN
7.18 SAFETY REFLECTORS
A 4.5" wide x 1" high red reflector shall be provided and installed on the inside, lower
outboard area of each exterior door. These reflectors shall warn oncoming traffic of
the open door while on scene.
Y�&N
7.19 GRAB RAIL
An exterior style 16" stainless steel grab rail shall be installed on the curbside of the
vehicle to the rear of the curbside entrance door. The grab rail shall be bolted
through the body skin and through the aluminum side structure with fender washers
and lock nuts on the interior and rubber gaskets under the feet of the grab rail on the
exterior. A grab rail mounted to the body skin is unacceptable.
YZN_
7.20 SIDE BODY SEAMS
All side center body seams are to be MIG welded, fully filled and body finished to
create a smooth, blemish free surface for final finishing and painting. There shall be
no side body molding applied or required.
Y N
7.21 REAR BUMPER
The rear step bumper shall be approximately 94" wide and step tread depth of 10.5".
The bumper shall be supported with a 1.5" x 1.5" x .250" wall steel tube sub frame
and have .250" steel angle outer frame construction. The bumper shall be bolted to
the vertical web of the chassis frame rails with .375" x 1.5" Grade 8 bolts, nuts and
washers. This configuration is designed to reduce body damage by directing impact
under the body and away from the patient area should a rear impact crash occur.
The center section of the bumper shall be 7" x 46" x 2" and be constructed of an
open grate diamond back material and shall flip -up over center to facilitate loading a
cot. The aluminum step shall be bolted to the sub -frame with .250" x 20 stainless
steel bolts for ease of replacement.
Y_N_
7.21.1 The removable end pods of the bumper are constructed of cast aluminum.
The height of the end pods shall be 4" and shall have 3" radius corners. The surface
of the end pods shall be finished with 375" slip resistant raised pattern and
embossed logo.
YA_N
7.22 DOCK BUMPERS
Two (2) rubber dock bumpers shall be provided and installed on the rear of the
vehicle, to cushion the vehicle against impact. These dock bumpers shall be in
addition to the specified rear bumper.
Y N
7.22.1 An aluminum diamond plate protection plate on the rear face above the rear
step shall be provided and TIG welded to ensure secure fit. Rear kick plate shall not
be screwed on or pop riveted.
Y_,N
7.23 TOW EYES
A pair of tow eyes shall be provided at the rear of the vehicle. They shall be recess
mounted into the kick plate and shall meet or exceed all standards related to towing
capacities and performance. v
Y X N
7.24 BODY HARDWARE
All body hardware, all compartment and entry doors shall be mounted on the body
with stainless steel screws. All stainless mounting screws shall be dipped in or
sprayed with electrolysis preventive solution before installation on the body. This is
required to minimize the process of electrolysis.
Y N
7.25 BODY PROTECTION
A full-length body rub rail shall be attached to both sides and extend from the body
below the compartment doors. This rub rail shall be constructed of 1.5" x 2" x .250"
"C" channel aluminum. The rub rails shall be attached to the lower margin of the
body skirt using 1" x .25"-20 stainless steel flat head mounting bolts with stainless
acorn nuts to the outside and plastic or nylon washers between the rub rail and body.
For additional protection and for compliance with state highway requirements, two [2]
heavy-duty composite mud flaps shall be installed behind the rear dual wheels. The
mud flaps shall extend the full.width of each set of dual wheels. The mud flaps shall
be black in color.
7.26 DRIVER AND PASSENGER CHASSIS STEPS
There shall be a fuel tank cover with a recessed double step attached to the
passenger side of the chassis cab and a driver side double step with an integrated
flip down battery cover and roll out battery tray. The covers shall be constructed of
.125" 3003 alloy aluminum diamond plate. There shall be a flip down step installed
on passenger side forward and above of the recessed double step. To provide for
increased road splash protection and ease of driver/technician entry and exit, fire
grade aluminum diamond plate with an open grate diamond back non -slip stepping
surface shall be installed on the chassis steps.
7.27 STONE GUARDS
The lower 21" of the front module wall shall have an aluminum diamond plate stone
guard TIG welded to ensure a secure fit. Stone guard shall not be screwed or pop
riveted.
The lower forward corners of the body shall have approximately 21" high aluminum
diamond plate rolled around the corner radius and terminate at the junction of the
cab and the body.
The lower rear corners of the body shall have approximately 16.5" high aluminum
diamond plate rolled around the corner radius and terminate at the rear kick plate
area.
7.28 FENDERETTES
Formed, rubber fenderettes shall be provided around each rear wheel well opening.
They shall help diminish damage to the wheel well area of the body caused by
stones and road debris.
7.29 LICENSE PLATE
A Cast Products model #LP0002-1 rear license plate holder (or equal) shall be
recessed into the rear of the body on the driver's side between the kick plate and
turn signal. It shall be constructed of polished cast aluminum and have two [2] LED
top lights to illuminate the plate. The bezel shall be mounted to the body with
stainless steel screws and include a .060" thick closed cell foam gasket to prevent
moisture from seeping behind the bezel.
Y N
YLN_
YXN_
Y4N_
8.0 INTERIOR PATIENT COMPARTMENT COMPONENTS
Patient Compartment Sound Levels: This vehicle shall provide an interior working
environment in which the ambient noise level is less than 80 dB as measured
according to AMD Standard 006, Sound Level Test Code for Ambulance
Compartment Interiors.
Patient Compartment Carbon Monoxide Levels: This vehicle shall provide an interior
working environment in which the carbon monoxide level is less than 10 ppm as
measured in accordance with AMD Standard 007, Carbon Monoxide Levels for
Ambulance Compartment Interiors.
Y N
8.1 CABINET GLASS
All cabinet doors incorporating acrylic glass, as sliding or hinged windows shall have
.250" thick smoked acrylic Plexiglas® as the standard material and 3/8" where
otherwise specified.
8.2 STAINLESS STEEL ROUND LATCHES
Stainless Steel Round Southco locking latches (or equal) shall be provided on each
door where applicable.
Y N
8.3 CABINETRY
The cabinetry in the patient compartment shall have picture framed window face
fronts fabricated from lightweight smooth aluminum material and laminated with a
minimum .028" Formica (or approved equal). The shelves and the supporting
structure shall be non -wood material and laminated with a minimum of .028" Formica
on both sides.
Non -supportive partitions shall be lightweight smooth aluminum material and
laminated with a minimum of .028" Formica on both sides. All vertical outside
corners and protruding edges of overhead storage shall be capped with 5" radius
satin finish anodized aluminum moldings or padded vinyl.
All cabinetry shall be sealed and molded to the floor with bright -anodized aluminum
molding. All interior materials, cabinetry, vinyl, foam, and installation used shall meet
or exceed FMVSS 302 requirements on flammability of interior materials (where
applicable). X/
Y (� N
8.4 COUNTERTOPS
The countertop in the primary action area of the patient compartment shall be non -
wood material, laminated with a minimum .028" stainless steel. The top shall be a
pan style with all seams sealed.
YXN
8.4.1 The countertop in the second action area of the patient compartment shall be
non -wood material, laminated with a minimum .028" stainless steel. The top shall be
a pan style with all seams sealed.
9.0 PATIENT COMPARTMENT LIGHTS
Patient compartment lighting shall consist of eight (8), LED dome lights with polished
bezels, switched from the action area control console. These lights shall be high
intensity LED with clear lenses. The lights shall be activated in separate banks of
four (4) lights each. There shall be one (1) bank over the squad bench and one (1)
bank over the primary cot. Two (2) switches shall be provided in the action area
console, each with high/off/low positions for independent operation of each bank. All
eight (8) LED dome lights shall be activated on "LOW" when either the curbside entry
door or rear entry doors are opened. There shall be a three -minute time delay
system activated by opening the entry doors. This system shall be battery hot and
turn the lights "OFF" at the three -minute pre-set time. No ceiling light shall protrude
into the patient compartment by more than 1.25".
9.0.1 THINLITE LIGHTS
Four (4) Trucklite model #80251C 18" LED panel lights, recessed into the ceiling
shall also be provided and installed. One (1) on/off position switch shall be provided
in the action area console.
9.0.2 An LED strip light shall be provided and installed in the primary action area.
This light shall have a manual "on/off' switch.
9.0.3 A rotary timer system shall be provided for the fluorescent lights. The system
shall be preset to automatically turn the lights off after activating. The timer shall be
from 5-60 minutes.
The patient compartment interior lights must meet the requirements set forth in AMD
Standard Test 016 Patient Compartment Lighting.
10.0 CEILING HEADLINER
The patient compartment headliner shall be constructed of a durable, high -gloss
white, plasticized Marlite, backed with a non -rigid non -wood material. The headliner
shall be securely affixed to the roof bows and to the .090" aluminum accessory plate
welded to the roof structure. There shall be a full-length inspection access/wire race
in the center of the ceiling, which provides access to the wiring harness and
antennae bases/leads. The access shall have removable padded vinyl covers.
10.1 FLOORING
A one-piece non -wood material sub -floor on all patient area floors less than 144" in
length shall be installed on top of the .090" thick aluminum sheet. The sub -floor shall
be securely fastened with sheet metal screws long enough to penetrate the 2" x 2"
body tubes below the .090" aluminum sheet. This process shall create a sandwich
effect for long lasting durability and a solid surface. All screws shall be filled and
sanded to provide a smooth surface for the linoleum covering. Floor lengths longer
than 144" shall include a two-piece plywood underlayment. Vinyl, anti-skid,
commercial grade, heavy-duty, non -porous floor covering shall be applied to the
entire floor in a one-piece seamless application. This commercial inlaid sheet vinyl
Y N
Y N
911111111111011
Y N
Y N
shall have minimums of nominal overall thickness of 2.03 mm. The flooring shall
comply with ASTM F 970 (modified) in regard to static load bearing and D-2047
James Test for slip resistance. There shall be a 5" roll -up splashguard installed on
the street side cabinet wall and the squad bench face. A waterproof sealant shall be
applied between the cabinetry and the floor at the cabinet and floor covering
juncture.
Y N
10.2 REAR THRESHOLD
There shall be a 6" wide, 16 ga. formed, stainless steel threshold protector installed
on the rear interior of the body. The protector shall run the entire width of the floor at
the door opening. A 2" wide, adhesive -backed non-skid material shall be installed on
the threshold piece to assist with safe entry and exit from the vehicle.
Y N
10.3 INTERIOR PROTECTION
A stainless -steel riser shall be provided on the lower half of the squad bench, to just
below the seating surface, and the street side cabinet face, up to an approximate
height of 13" from the floor. It shall protect the vertical surfaces from scratches,
marks and debris and shall be easily cleaned.
YXN
10.4 INTERIOR COLORS AND MATERIAL
The Formica color for all cabinets within the patient compartment shall be Stone
Graffix #503 (GreyM/hite).
YN_
10.4.1 The Formica shall have a matte finish.
Y_N
10.4.2 The LonPlate II brand flooring color shall be Gun Metal (dark gray) #424.
YN_
10.4.3 The upholstery color shall be Gunmetal #MV102 (Dark Gray).
Y_N_
11.0 LEFT SIDE CABINETRY
11.1 ACTION AREA
An efficient and accessible action area shall be located to the right of the attendant
seat. Oxygen and suction/aspiration equipment outlets shall be readily accessible. It
shall provide a counter for the attendant's use. The counter shall have a 3/4" lip to
prevent items from falling. For the attendant's safety, the foremost vertical leading
edge and top horizontal edge of the action area cabinet shall be trimmed with fabric
backed padded vinyl. The foam padding shall be 3/8" high -density foam and shall
have a R-factor of 0.25. All seams are to be machine stitched for proper fit and
durability.
Y N
11.2 ACTION AREA CONTROL PANEL
All patient compartment lighting, environmental equipment and other indicators and
controls critical to the care of the patient shall be controlled from a switching console
located to the right side of the rear facing Technician's seat. The switch console
shall be located in a cabinet face cut at an approximate 30-degree angle above the
action area and below the overhead cabinet. The switch panel is designed to
provide easy operation and high visibility from either the rear facing Technician's
seat or side mounted CPR seat. To facilitate easy troubleshooting and maintenance
or repair, the controls for all ambulance conversion functions shall be basic,
automotive style, non -programmable type controls. This type of control mechanism
can be easily repaired by department maintenance personnel and does not require
electronic interaction with a third party for programming or problem solving. The
switches shall be moisture resistant, Euro-style, rocker -type, and shall be UL listed
and CSA approved. Each switch shall have one or more LED indicator lights integral
to the switch rocker indicating the function status. Switches may be simple ON/OFF
type or multi -position rockers or rotary, stepped -position switches, depending upon
their specific function. The switch function legends shall be engraved plastic inserts.
The backlighting shall light the words themselves rather than the background.
Backlighting and switch perimeter lighting shall be accomplished with electro-
luminescent light strips attached to the backside of the switch panel. This type of light
source shall be used for consistent light output, low amp draw, and extended service
life. The switch panel shall contain the following switches and controls:
Heat/Cool Fan Speed Control: Rotary, stepped -position control selecting Hi, Med,
Lo, Off
Heat/Cool Mode Selector: Two -position rocker control selecting Heating or Cooling
function
Left Dome Lights: Three -position rocker control selecting Lo, Off, Hi for curbside
dome lights
Right Dome Lights: Three -position rocker control selecting Lo, Off, Hi for street side
dome lights
Suction Pump: ON/OFF control selecting Thomas suction pump
Spare Switch: (1) Spare switch and (3) Blank positions for future use
Patients Status Buzzer, If Specified: Push button control activating buzzer to signal
change in patient status
Patient Status Indicator Lights, (3) Locking push button controls, Red, Yellow, Green,
selecting indication of patient status, signal to front switch panel
Exhaust Fan Control: Rotary, stepped -position control selecting Hi, Med, Lo, Off for
patient compartment exhaust fan.
11.3 RADIO CUTOUT
An angled housing 5"H X 9" W for two-way radio with power/ground and ignition
studs shall be provided in the forward section of the overhead squad bench cabinet.
A coax cable from this housing shall run to center of mod roof. A 1/4" black Kydex
cover shall also be provided.
11.4 SPEAKER SYSTEM
Two (2) speakers shall be provided and mounted in the rear module ceiling. They
shall be connected to the cab AM/FM radio. A separate volume control and fader
shall be provided in the rear action area.
11.5 ACTION AREA OVERHEAD CABINET
Y N"***4
Y_�N
YXN_
A cabinet shall be installed above the action area and shall be provided with one [1]
adjustable shelf.
YXN
11.5.1 It shall have "restocking type" Plexiglas doors. The doors shall slide, than flip -
up for easy, full width access.
YX-N
11.5.2 A full length, aluminum handle shall be provided on each door
Y ?C N
11.6 WRITING DRAWER BELOW ACTION AREA
A writing drawer shall be provided below the action area, in the rearward position. It
shall have approximate dimensions of 2 3/4" high x 14" wide x 15" deep. It shall
have a Plexiglas writing surface with flush mounted hinges at the rearward section,
so that when the tray is full extended, the writing surface can be lifted to allow easy
access to a storage area below. In the closed position, it shall be flush with the front
edge of the cabinetry. The storage area shall be large enough to hold writing
instruments, a bound notebook, calculator or small miscellaneous items.
Y_&N_
11.7 CABINET BELOW ACTION AREA
A storage cabinet shall be provided below the 1st action area, in the forward position.
This cabinet shall be made of the same materials as the rest of the cabinets. This
cabinet is designed for inverter, miscellaneous or radio module storage.
Y � N
11.7.1 It shall have sliding Plexiglas doors.
YK N
11.7.2 A full length, aluminum handle shall be provided on each door.
YX_N_
11.8 LOWER STREETSIDE CABINET
A cabinet approximately 16" wide x 12" high and full depth shall be provided under
the 2nd action area.
Y x N_
11.8.1 It shall have tilt -out door.
Y V N_
11.8.2 A round stainless steel SouthCo latch (or equal) shall be provided on the
door.
Y"fN
11.9 DOUBLE CABINET
There shall be a double cabinet above the CPR seat. The cabinet shall be sized
to be compliant with the KKK 1822 revision F specification.
Y Y—N_
11.9.1 It shall have a single 3/8" flip -up Plexiglas door with hold -open devices.
Y-?—(N_
11.9.2 A stainless Steel Round Southco latch (or equal) shall be provided on the
door.
Y X N
11.10 SECOND ACTION AREA
The 2nd Action Area, the Technician's secondary work center, shall be an open
countertop designed for efficiency and accessibility. The action area shall be located
to the right of the CPR seat in the street side cabinet wall and accessible from the
Squad Bench also. The countertop shall have dimensions of approximately 23.5"
wide x 18" deep with a .750" lip to prevent items from sliding off the work surface.
The countertop surface and lips shall be laminated with a minimum of .028"
Formica® and both horizontal and vertical corner seams shall be sealed the full
length of the seam to prevent seepage of spilled liquids. For the Technician's safety,
the lower horizontal edge of the action area rear overhead cabinet shall be trimmed
with fabric backed padded vinyl. The foam padding shall be .375" thick high -density
foam.
11.11 OVERHEAD CABINET
A cabinet shall be installed above the supply cabinet and shall be provided with one
[1] adjustable shelf.
11.11.1 It shall have "restocking type" Plexiglas doors. The doors shall slide and flip -
up for easy, full width access.
11.11.2 A full length aluminum handle shall be provided on each door.
11.12 SUPPLY CABINET
A supply cabinet shall be provided in the rearward section of the street side interior,
below the overhead cabinet. It shall be accessible from both the interior and the
exterior (D4) compartment.
11.12.1 It shall have vertically hinged, swing -out doors backed with aluminum
diamond plate.
11.12.2 A stainless Steel Round Southco latch (or equal) with a roller ball catch shall
be provided on each door.
12.0 KNOX EMS DRUG VAULT STREETSIDE CABINET
One (1) customer supplied Knox Med Vault model #5502 shall be installed in the street side
cabinet. Exact location shall be determined at pre -build. A 12-volt constant power source shall
be supplied to the installation area.
13.0 PATIENT COMPARTMENT EXHAUST VENT
Detmar #751 A (or equal) three -speed power exhaust vent having a 240-cfm air flow
rating shall be installed in the upper left side rear wall, with approximate dimensions
of 6" wide x 8" high. The resister coil shall be mounted in the fan air flow. A switch
shall be mounted at the right hand of the technician in the action area switch
console. A positive closure to prevent destabilization of the patient compartment
shall be provided.
14.0 OXYGEN COMPARTMENT
The oxygen cylinder storage compartment shall be located in the street side front
compartment D1. Access to the regulator, contents gauge, and cylinder shut-off
Y N
Y N
Y N
Y N
Y N
Y N
Y N
valve from the interior of the vehicle shall be by means of a hinged .250" thick
Plexiglas® door in the forward wall of the action area. This opening shall be trimmed
with a black, ABS formed bezel to protect the Technician's hands and provide a
finished opening. The compartment shall be vented through the exterior door with a
minimum 28 square inch opening. The vent opening shall be covered with a
polished aluminum vent cover. It shall be attached with stainless screws. The
oxygen cylinder retention bracket shall be mounted to the wall of the compartment by
Grade 8 bolts tapped into a .250" aluminum plate welded onto the inboard side of the
compartment wall. This retention bracket must meet or exceed AMD Standard 003,
Oxygen Retention System. The finished oxygen system including regulator, contents
gauge, hoses, outlets and flow meter must meet or exceed the requirements of AMD
Standard 015, Ambulance Main Oxygen System Test.
Y N
15.0 WIRING MODULE
An angled cabinet forward of the rear facing Technician's seat shall house the main
bank of electrical components. Adequate ventilation shall be supplied through two (2)
polished metal, louvered vents located near the top and bottom of the door.
YN
15.1 The cabinet shall have a vertically hinged door and shall be provided with a
locking stainless -steel round latch. This door shall hinge on the left side for ease of
maintenance and repair.
Y N
16.0 WALK-THROUGH WITH POCKET DOOR
There shall be an opening approximately 52" high x 20" wide between the chassis
cab and the box module.
Y�C N
16.1 An aluminum partition wall framed with .125" x 2" x 2" aluminum tubing placed
on 16" centers and plated with .060" aluminum formed and welded to the roof, both
sides, and floor shall be installed. The patient compartment side of the partition shall
be covered with 1/4" plywood laminated with a minimum of .028" plastic. The driver's
side of the partition shall be covered with the OEM wall as well as a mildew resistant
marine style carpet of a color that matches the cab interior colors. Y
Y `v N
17.0 EQUIPMENT FURNISHED
The ambulance cab shall be equipped with an OEM supplied in -dash air conditioner
and a hot water heater. The patient compartment shall be equipped with a
combination hot water heater/air conditioner and a power exhaust vent. Front and
rear heaters and air conditioners shall operate as separate and independent
environmental systems. The controls for the rear environmental systems shall be
located in the action area switch panel. The addition of the rear HVAC system shall
have no deleterious effect upon the chassis system and especially the windshield
defroster system as described in FMVSS 103, Windshield Defrosting and Defogging
System.
Y N
17.1 A combination heater/air conditioner having an air output of 650 cfm at 0 static
pressure, a cooling capacity of 32,000 BTU and a heating capacity of 35,000 BTU
shall be installed above the walk-through door on the front bulkhead. There shall be
two insulated plenums running the full length of the modular body in the ceiling with
(4) adjustable outlet vents in each plenum. There shall also be one adjustable outlet
vent on the front bulkhead. This system shall be certified to KKK standards by a
third -party test facility and a copy of the test results shall be included with the bid.
Y N
17.2 For durability purposes, metal "Y's" shall be used for heater hose tie in.
17.3 An auxiliary air conditioner condenser with dryer shall be provided under the
body.
16101L
17.4 The patient compartment heat and air conditioning shall be controlled and
maintained through a digital, manually controlled thermostat.
Y N
18.0 ALS CABINET
An Advanced Life Support cabinet shall be provided in the right side of the forward
wall. It shall be divided into sections to accommodate the storage of sensitive
equipment and supplies, such as ALS equipment, Laerdal charger, medical boxes,
etc. The ALS cabinet and all shelves shall be finished with black Line-X, sprayed on
rubber coating.
Y N
18.0.1 The upper compartment shall have a top hinged, single door with a locking
SouthCo round latch.
Y_N_
18.0.2 The bottom compartment shall have three [3] adjustable, .125" aluminum
shelves with a 1 Y2" lip on all sides, mounted on "C" channel style tracking.
YX N
18.0.3 The bottom compartment shall be open faced with no doors.
Y N )C
19.0 VACUUM FORMED UPHOLSTRY
All seating and backrests (including the technician's seat) in the patient compartment
shall be constructed of 60-ounce vacuum formed, seamless vinyl.
Y X N_
20.1 MACHINE STITCHED UPHOLSTERY
All trim panels in the patient compartment shall be constructed of minimum 32 ounce
machine stitched fabric backed expanded vinyl. All trim panels shall match the seats
and backrests.
Y N
21.2 ATTENDANT SEAT
A USSC Valor rear facing, R-Back attendant seat with an integrated child seat
installed at the head of the patient cot. The attendant seat shall be a two (2) position
swivel seat mounted on a pedestal base with a heavy duty seat frame for an ABTS
(All Belts to Seat) application with four (4) point/four (4) retractors single click internal
mount belt system. The seat shall be 20" wide with discontinuous recline and a 6"
horizontal slide for fore and aft adjustment(s). The seat shall be KKK-A-1822F
Change Notice 8 compliant and conform to all applicable FMVSS and SAE J3026
requirements. Documentation from a certified independent testing facility shall be
required stating the seat has passed SAE J3026 requirements and tested in
accordance with SAE J2917, Occupant Restraint and Equipment Mounting Integrity
— Frontal Impact System -Level Ambulance Patient Compartment and SAE . J2956,
Occupant Restraint and Equipment Mounting Integrity — Side Impact System -Level
Ambulance Patient Compartment. The seat shall be padded and covered with sewn
matching antimicrobial vinyl upholstery. It shall be mounted 10" away from main wall
and 8.5" from the AC chute on linen cabinet.
22.3 CPR SEAT
A CPR seat shall be installed on the street side of the patient compartment aft of the
main action area counter. The CPR seat shall be KKK-A-1822 Change Notice 8
compliant with VALOR A-VAL shelf mount back frame and internal bolsters. The
seat shall consist of a four (4) point/four (4) retractors single click internal mount belt
system. The seat shall conform to all applicable FMVSS and SAE J3026
requirements. Documentation from a certified independent testing facility shall be
required stating the seating configuration has passed SAE J3026 requirements and
tested in accordance with SAE J2917, Occupant Restraint and Equipment Mounting
Integrity — Frontal Impact System -Level Ambulance Patient Compartment and SAE
J2956, Occupant Restraint and Equipment Mounting Integrity — Side Impact System -
Level Ambulance Patient Compartment. The VALOR A-VAL shelf mount back frame
and the seat shall be padded and covered with cushioned, color coordinated, cut and
sewn vinyl. There shall be storage under the seat base.
Y N
22.5 SQUAD BENCH
A squad bench seat with two (2) individual seating positions and two (2) VALOR A-
VAL, or equal, shelf mount back frames with internal bolsters will be installed on the
curbside of the patient compartment. There shall be two (2) seat belts shall consist
of four (4) point/four (4) retractors single click internal mount belt system. The squad
bench seats shall be KKK-A-1822F Change Notice 8 compliant and conform to all
applicable FMVSS and SAE J3026 requirements. Documentation from a certified
independent testing facility shall be required stating the seating configuration has
passed SAE J3026 requirements and tested in accordance with SAE J2917,
Occupant Restraint and Equipment Mounting Integrity — Frontal Impact System -Level
Ambulance Patient Compartment and SAE J2956, Occupant Restraint and
Equipment Mounting Integrity — Side Impact System -Level Ambulance Patient
Compartment. The VALOR A-VAL shelf mount back frames and the bench shall be
padded and covered with cushioned, color coordinated, cut and sewn vinyl. A
storage area shall be provided in the squad bench base under the lift up cushion.
The squad bench base shall be constructed of .90" thick aluminum for maximum
storage capacity and minimum weight. The interior of the squad bench shall be
sprayed with sound absorbing polyurethane material.
Y N
22.6 REINFORCED SAFETY NET
A reinforced safety net shall be located at the head of the squad bench. The
sharp/waste container shall be on tip out, door at head of bench facing the aisle and
easily accessible from the front of the squad bench. The sharp/waste container size
and placement shall match the Department's newest ambulance.
Y N
22.7 OXYGEN BOTTLE STORAGE
A single oxygen bottle storage system shall be provided and installed at the side of
the ALS cabinet, in the bottom of the health center. It shall provide vertical storage
of one (1) "D" size oxygen bottle. Cast brackets will be used to house customer's
bottle.
22.8 ADDITIONAL OXYGEN BOTTLE STORAGE
A double oxygen bottle storage system shall be provided and installed against the
front wall of the D1 compartment. It shall provide vertical storage of two (2) "D" size
oxygen bottles. Cast brackets will be used to house customer's bottles.
Y N
Y N
22.8.1 A single oxygen bottle storage system shall be provided and installed against
the front wall of the D1 compartment. It shall provide vertical storage of one (1) "D"
size oxygen bottle. Cast brackets will be used to house customer's bottles.
Y�C N
22.9 SQUAD BENCH CABINET
A cabinet shall be located over the squad bench at the ceiling level, rearward of the
entry/egress door opening. This cabinet shall be divided into three (3) separate
sections. The cabinet shall be finished in the same material as the rest of the interior
cabinets. This cabinet shall be compliant with the KKK 1822 revision F specification.
YK N
22.9.1 There shall be three (3) 3/8" flip -up Plexiglas doors.
Y4",N
22.9.2 A stainless Steel Round Southco latch (or equal) shall be provided on each
door.
Y N
23.0 IV HOLDERS
Four [4] ceiling mounted Cast Products 2008-1 recessed IV holders shall be
supplied. These shall be located at the head and foot areas, two [2] over the squad
bench and two [2] over the primary cot. They shall have a rubber, foldaway storage
when not in use. Each holder must have the capacity to hold two [2] bottles and
have Velcro securing straps.
Y)�N
23.1 COT MOUNT
A Stryker Power Load cot mount shall be supplied. It must accommodate the Stryker
Power Pro XT. y
Y /� N
The cot mount shall be located in the center of the patient compartment.
YXN
23.2 ASSIST RAILS
One [1] 90" long, 1.50" diameter, smooth satin finished overhead grab rail shall be
provided and securely fastened to the ceiling over the primary cot. One [1] 60" long,
1.50" diameter, smooth satin finished overhead grab rail shall be provided and
securely fastened over the squad bench. The grab rails shall be fastened with bolts,
washers and nuts of the appropriate dimension, through the interior ceiling panel and
through the .090" aluminum accessory plate welded into the roof structure. Assist
rails fastened with self -tapping machine screws are not acceptable. These grab rails
must meet or exceed AMD Standard 008, Load Test for Ambulance Patient
Compartment Grab Rail.
Y N
23.3 SIGN
Two self-adhesive "NO SMOKING OXYGEN EQUIPPED" and "FASTEN
SEATBELT" sign (1) shall be installed in the 1st action area.
24.0 OXYGEN
The medical oxygen system shall be capable of storing and supplying a minimum of
3000 liters of oxygen. A suitable high-pressure hose shall be provided. The
concealed oxygen supply hose shall be .250" ID, .50" OD nylon base with polyester
fiber reinforcing. This electrically conductive hose shall be certified to 1,875 psi and
have a 7,500-pound burst rating. The fittings shall be DISS and flare and be
securely crimped to the barbed fittings by means of compressed copper sleeves.
Oxygen supply hose shall be routed through the ceiling of the ambulance body and
be secured with non-abrasive plastic "C" clamps. Oxygen lines should not be
encased in insulation and should be free moving to enable easier maintenance and
repair. The entire oxygen system shall be subjected to a 155-psi leak test for 24-
hours before installation of panels or covers that may obscure or hide the system
components. After the vehicle is completed, a test as prescribed by AMD Standard
015 shall be conducted for a period of four (4) hours to insure system integrity. This
test shall be performed using nitrogen gas to purge the lines of all moisture and
foreign debris. Upon completion of the test, the lines shall be bled free of nitrogen
and capped. This medical oxygen system shall meet or exceed AMD Standard 015,
Ambulance Main Oxygen System Test.
24.0.1 The oxygen system shall have three (3) outlets, (2) on action area wall and (1)
over squad bench. The department shall specify the brand of quick connectors to be
used. A compartment shall have fully adjustable stainless -steel rings for the 02
tank. The rings shall be located in the front of the compartment (tank will be
provided by the department).
24.0.2 Oxygen outlets to be Cemtron/NCG brand
24.0.3 One (1) gravity type Thorpe tube oxygen flow meter shall be provided. This
flow meter shall be certified by the equipment manufacturer to meet the appropriate
FDA standards for medical oxygen flow meters.
24.1 REGULATOR
A 50-psi preset medical oxygen regulator shall be provided and installed on the
supply end of the oxygen system hose. This regulator shall be certified by the
equipment manufacturer to meet the appropriate FDA standards for medical oxygen
flow meters.
24.2 OXYGEN CONTENT GAUGE
A digital oxygen content gauge with an alarm shall be provided and wired to the
rotary timer.
24.3 CARBON MONOXIDE MONITOR
Y N
Y N
Y N
Y N
Y N
OEM=
Y N
A carbon monoxide monitor with an alarm shall be provided and installed in the
action area, within the patient compartment.
YEN_
24.4 ELECTRIC OXYGEN SHUT OFF
An electric shut off switch for the oxygen system shall be provided and installed in
the rear action area switch panel. The system shall include a manual bypass.
YA_N_
24.5 PORTABLE/ ONBOARD SUCTION AND ASPIRATION SYSTEM
A portable/onboard, complete self-contained S-SCORT VX-2 dual mode unit with
battery charger shall be installed on the primary action area wall. It shall include a
charging retention bracket hard -wired to 12 VDC power. A 1,200-cc suction canister,
6' suction tubing, and suction tip shall be supplied with unit.
YXN_
24.6 SHARPS/BIO-HAZARD
A sharps container with a crash stable mounting bracket shall be supplied and
shipped loose. A biohazard container with lid and twelve [12] red biohazard bags
shall be shipped loose for installation by the department.
YX N
24.7 PATIENT CODE SIGNAL SYSTEM
In the action area switch console, there shall be three [3] colored switches (red,
yellow and green) that activate corresponding indicator lights in the driver's switch
console. In addition, there shall be a switch in the action area switch console that
activates a buzzer in the driver's compartment. These lights and buzzer shall be
used to notify the driver of any change in the patient's status.
Y4,-N
24.8 RADIO WIRING
Radio wiring as follows:
1. 10-gauge A+ to console with ignition.
2. 8-gauge A+ and A- to console in cab, hot.
3. 8-gauge A+ and A- to radio compartment in box, hot.
4. Three (3) antenna accesses will be provided inside box: front -center, middle -
center, and rear -center.
5. Two (2) RG-58 cables installed at rear -center and middle -center access
points with NMO-style antenna mounts. Both will be run to radio
compartment. Antenna cables will have 18" excess at both ends.
6. Wiring for the intercom system for cab and patient compartment to be
determined at the pre -build meeting. Department will supply components of
intercom system. 10 conductor strobe cables shall be run from center console
to action area and from action area to radio housing at end of squad bench.
Y N
24.9 FIRE EXTINGUISHERS
Two (2) 5-pound rated ABC fire extinguishers with mounting brackets shall be
furnished with the ambulance. These shall be shipped loose to allow the department
to install in the desired locations.
Y_N_
24.9.1 Two (2) Two (2) Streamlight, model #SL-20-X handheld flashlights, each with
charger base, shall be provided. Mounting location shall be one (1) on the driver
side front console located directly behind the gear shift selector and one (1) located
in the rearward ALS health center located halfway up.
YXN_
25.0 MODULE SURFACE PREPARATION
A corrosion inhibitor shall be used on specified exterior surfaces and on specified
fasteners, hinges and accessories that are subject to the effects of corrosion due to
the electrolytic process that occurs between dissimilar metals. The product,
designated as ECK, is a petroleum -based substance with a very slow rate of
desiccation. The substance functions as a barrier to water, thus minimizing the
electrolytic process. It shall be applied in the following conditions and to the
following accessories and fasteners:
1. Behind stone guards or any other surface area where there is direct contact
between dissimilar metals is direct contact between dissimilar metals.
2. On light assemblies utilizing self -tapping mounting screws that penetrate the body
that penetrate the body.
3. On screws and screw holes for any accessory whose holes are drilled and tapped
are drilled and tapped.
4. On the body surface when any accessory without a rubber or composite gasket is
to be mounted (i.e. entry or compartment door hinges or light assemblies without
gaskets) or composite gasket is to be mounted, i.e. entry or compartment door
hinges or light assemblies without gaskets.
ECK shall not be applied in the following conditions:
1. When mounting any accessory that has a rubber or composite gasket.
2. On light assemblies, which have plastic inserts for mount screws. Y_N
25.1 PAINT
To produce a high -quality paint finish and to comply with the paint manufacturer's
certification requirements for support of the warranty, the preparation and painting
process described below must be used.
Prior to initiating the surface preparation process, all hardware, handles, light
fixtures, door hinges, corner trim, etc. shall be removed from the body. Additionally,
any portion of the chassis, which does not require refinishing, shall be protected from
the ensuing process.
To rid the aluminum body of any extraneous materials or material impurities the
entire surface shall be washed and wiped dry with a certified wax and grease
remover. Excess weld material shall be removed by grinding all welds, seams, and
any other body imperfections. The entire surface shall then be sanded with 80 - 150
grit dry sandpaper to provide good adhesion for any fillers and primers. The required
areas will be filled with approved premium lightweight filler and sanded smooth. A
premium polysurfacer will be applied directly over these areas to ensure adequate
base for application of primers.
The entire surface shall be cleaned again with certified wax and grease remover
before application of any primers. A self -etching primer shall be applied to provide a
base for adequate adherence of materials to be applied in subsequent steps of this
process. A high -quality urethane primer surfacer shall then be applied. The entire
surface to receive topcoat will be sanded smooth to ensure a level and defect free
surface.
Door edges and doorjambs shall be prepared similarly to other body surfaces and
finish painted with a certified topcoat paint. The entire surface of vehicle body shall
be DA finish sanded with no coarser than 320 grit dry sandpaper. The surface shall
be washed and wiped once again with certified wax and grease remover and tacked
for application of urethane sealer.
A full wet coat of urethane primer sealer shall be applied and allowed to flash per
specifications. Basecoat color will be applied to ensure color correctness then clear
coated with a minimum of 2 full wet coats of qualified urethane clearcoat and baked
at 140 degrees for 30 minutes.
Surfaces to receive striping and graphics shall then be sanded with 800 grit dry
sandpaper and masked off for application of additional color(s). Basecoat color shall
be applied to stripe and graphic areas until color is correct. Entire sanded surface
shall then be unmasked, inspected, and receive a minimum of 2 full wet coats of
certified urethane clearcoat. Topcoat will be baked again at 140 degrees for 30
minutes.
Body is then color sanded, compounded, buffed, and polished to a smooth defect
free finish.
Upon final assembly, door hinges, hinge side of doorjambs and all stainless -steel
mounting hardware shall be coated with ECK, a corrosion inhibitor and permanently
mounted to vehicle.
Y N
25.2 BODY PAINT COLOR
The body shall be painted a single color of red with PPG base coat, clear coat paint
processes. Exact Color to be determined at pre -build
Y_N-A
25.3 ROOF PAINT COLOR
The roof shall be painted a single color of white with PPG base coat, clear coat paint
processes.
Y_ i N_
25.4 SAFETY STRIPE
The body shall have a 2" wide reflective safety stripe around the entire perimeter
position above the main stripe. A QRS heartbeat shall be position on each side
towards the rear of the module.
YXN
25.5 REAR BARRICADE CHEVRON
There shall be 6" solid red 983-72 diamond grade reflective 60-degree stripes and 6"
fluorescent yellow green 983-23 diamond grade reflective stripes across the entire
back of the ambulance. This design shall provide the greatest amount of reflectivity
for the overall safety of the vehicle and crew. The chevron pattern shall slant
downward on both sides on the rear of the vehicle at an angle of 60 degrees,
pointing in the direction of the bottom rear corner of the tailboard. The pattern should
resemble an inverted V with the point at the top center of the ambulance.
Y N
25.6 MAIN SCOTCHLITE STRIPE
A white main Scotch lite stripe shall be provided, "Straight" design on the chassis
and body sides (including the rear body). It shall start at the front of the module and
run along each side of the body. The main stripe shall wrap around the rearward
section of the body, completing the perimeter. The main stripe shall not exceed 14
inches in width. Scotch lite color, stripe dimension and layout shall be provided by
the department after award of bid.
25.7 PINSTRIPING
There shall be 1/4" wide black vinyl pinstripes around the entire perimeter of the
body, positioned above and below the main color stripes.
Y)( N
25.8 RUBRAIL SAFETY STRIPE
There shall be a 3/4" wide red reflective stripe ran through the center of the "C" style
rub rail.
Y lv N_
25.9 MARKINGS
A reflective graphics and lettering package shall be supplied and installed to match
the Department's most recent ambulances. Included shall be Star of Life decals,
Department door logos, numbers, and all lettering.
Y2—(N
26.0 OPERATOR'S MANUAL
A vehicle owner's manual (reference handbook) for the ambulance shall be provided
in an 8 1/2" x 11" three-ring hard cover loose leaf binder. It shall contain copies of
the chassis manufacturer's warranties and a full set of factory repair manuals for the
engine, transmission, and chassis, including wiring schematics. The bidder shall also
provide all available troubleshooting software for engine, transmission, and chassis.
Successful bidder shall also provide copies of the ambulance manufacturer's
warranties and operating/service instructions, component manufacturer's equipment
information, installation, operating, service instructions, warranties, etc., and a
complete wiring diagram or schematic with circuits and components clearly and
accurately labeled. Verification of the chassis pre -delivery inspection and a copy of
the ambulance manufacturer's quality assurance form with all of the data referred to
in Section AA-1.10 shall be supplied should the department request them.
YX_N
26.1 OPERATING INSTRUCTIONS
To provide a safe working environment for emergency medical technicians to provide
care of patients, this emergency vehicle must be operated in the safest manner
possible. To provide proper training for all operators of this emergency vehicle, a
professionally produced operations videotape shall be included with the vehicle at
the time of delivery. The videotape shall present all aspects of the operation of the
vehicle including front and rear switch panel operation; daily checkout and
maintenance procedures; location of and precautions about the main electrical panel
and components. The authorized representative of the manufacturer shall present
the videotape and review its contents with the potential operators of the vehicle and
shall answer any questions regarding its optional features and safe and correct
operation.
YX N
26.2 ELECTRICAL SCHEMATICS CD
To provide for continued quality operations of the new ambulance and timely
information regarding the vehicles electrical system, the manufacturer shall provide a
compact disc with the basic electrical schematics for this emergency vehicle. This
CD shall be delivered to this department as an item included in the New Vehicle
Owner's Manual.
Y_N
27.0 MISCELLANEOUS EQUIPMENT
All items listed and as shown in attached quotes shall be included in total bid price.
Department will purchase and install all components unless otherwise specified
previously.
Motorola Two -Way Radios as listed in quote attached.
Quala-Tel Enterprises Headsets as listed in quote attached.
Mobile Data Terminals with mounting hardware, radio modem and GPS unit as listed
in quote attached.
BID NAME
FOR BIDS DUE
SCSQiJ T$ 8�
BID/PROPOSAL sib
CITY OF SOUTH BEND
1565 ,
Spec P — One (1) or More 2020 or Newer Emergency Medical Vehicle
November 10, 2020; 9:00 a.m.
Description (Year/Make/Model Unit Price
Year
Make/Model - Trade In
Unit Price
I'
$
$
Option#
Description
XI/
Bidder (Firm):
Address:
City/State/Zip
Telephone
Number:
(10ue 6- ly , 6 a tfZI23
Fax Number:
By
I( S3g-: 6-S
(Signature)
(Printed Name)
(Title)
0,03 TH &
VI iS d
PEACE
r�
s
xs6s
BID NAME: ONE OR MORE, 2020 OR NEWER, EMERGENCY MEDICAL VEHICLE
— SPEC F
ADDENDUM NO. 1
Date: November 5, 2020
To: All Plan Holders
From: Linda M. Martin, Clerk of the Board of Public Works
The following BID/PROPOSAL sections shall be changed as noted:
1) Section 1.6 Delivery: disregard 180 days. Bidder shall state a delivery date as accurate as
possible.
2) Section 2.0 Cab: Interior Gray Mordura Cloth should be Gray Vinyl.
3) Section 2.5 Rear Axle: replace air suspension with Liquid Spring.
4) Section 27.0 Miscellaneous Equipment should be deleted in its entirety.
You must acknowledge receipt of this addendum by signing the first page,
returning it via facsimile to (574) 235-9171, and a copy of the first page must
be included with your bid.
Version 4/2/2019
When the prospective Contractor is unable to certify to any of the statements below, it shall attach an explanation to this Affidavit.
CONTRACTOR'S NON -COLLUSION AND NON -DEBARMENT AFFIDAVIT,
CERTIFICATION REGARDING INVESTMENT WITH IRAN, EMPLOYMENT ELIGIBILITY
VERIFICATION, NON-DISCRIMINATION COMMITMENT AND CERTIFICATION OF USE
OF UNITED STATES STEEL PRODUCTS OR FOUNDRY PRODUCTS
(Must be completed for all quotes and bids. Please type or print)
STATE OF OR -TO )
SS:
��•� COUNTY )
The undersigned Contractor, being duly sworn upon his/her/its oath, affirms under the penalties of perjury that:
1. Contractor has not, nor has any other member, representative, or agent of the firm,
company, corporation or partnership represented by him, entered into any combination, collusion
or agreement with any person relative to the price to be bid by anyone at such letting nor to
prevent any person from bidding nor to induce anyone to refrain from bidding, and that this bid
is made without reference to any other bid and without any agreement, understanding or
combination with any other person in reference to such bidding. Contractor further says that no
person or persons, firms, or corporation has, have or will receive directly or indirectly, any
rebate, fee, gift, commission or thing of value on account of such sale; and
2. Contractor certifies by submission of this proposal that neither contractor nor any of its
principals are presently debarred, suspended, proposed for debarment, declared ineligible, or
voluntarily excluded from participation in this transaction by any Federal department or agency;
and
3. Contractor has not, nor has any successor to, nor an affiliate of, Contractor, engaged in
investment activities in Iran.
a. For purposes of this Certification, "Iran" means the government of Iran and any agency or
instrumentality of Iran, or as otherwise defined at Ind. Code § 5-22-16.5-5, as amended from
time -to -time.
b. As provided by Ind. Code § 5-22-16.5-8, as amended from time -to -time, a Contractor is
engaged in investment activities in Iran if either:
i. Contractor, its successor or its affiliate, provides goods or services of twenty million
dollars ($20,000,000) or more in value in the energy sector of Iran; or
ii. Contractor, its successor or its affiliate, is a financial institution that extends twenty
million dollars ($20,000,000) or more in credit to another person for forty-five (45)
days or more, if that person will (i) use the credit to provides goods and services in
Non -Collusion Non-Debannent Affidavit Non Iran Form
the energy sector in Iran; and (ii) at the time the financial institution extends credit, is
a person identified on list published by the Indiana Department of Administration.
4. Contractor does not knowingly employ or contract with an unauthorized alien, nor retain
any employee or contract with a person that the Contractor subsequently learns is an
unauthorized alien. Contractor agrees that he/she/it shall enroll in and verify the work eligibility
status of all of Contractor's newly hired employees through the E-Verify Program as defined by
I.C. 22-5-1.7-3. Contractor's documentation of enrollment and participation in the E-Verify
Program is included and attached as part of this bid/quote; and
5. Contractor shall require his/her/its subcontractors performing work under this public
contract to certify that the subcontractors do not knowingly employ or contract with an
unauthorized alien, nor retain any employee or contract with a person that the subcontractor
subsequently learns is an unauthorized alien, and that the subcontractor has enrolled in and is
participating in the E-Verify Program. The Contractor agrees to maintain this certification
throughout the term of the contract with the City of South Bend, and understands that the City
may terminate the contract for default if the Contractor fails to cure a breach of this provision no
later than thirty (30) days after being notified by the City.
6. Persons, partnerships, corporations, associations, or joint venturers awarded a contract by
the City of South Bend through its agencies, boards, or commissions shall not discriminate
against any employee or applicant for employment in the performance of a City contract with
respect to hire, tenure, terms, conditions, or privileges of employment, or any matter directly or
indirectly related to employment because of race, sex, religion, color, national origin, ancestry,
age, gender expression, gender identity, sexual orientation or disability that does not affect that
person's ability to perform the work.
In awarding contracts for the purchase of work, labor, services, supplies, equipment, materials,
or any combination of the foregoing including, but not limited to, public works contracts
awarded under public bidding laws or other contracts in which public bids are not required by
law, the City, its agencies, boards, or commissions may consider the Contractor's good faith
efforts to obtain participation by those Contractors certified by the State of Indiana as a Minority
Business ("MBE") or as a Women's Business Enterprise ("WBE") as a factor in determining
the lowest, responsible, responsive bidder.
In no event shall persons or entities seeking the award of a City contract be required to award a
subcontract to an MBE/WBE; however, it may not unlawfully discriminate against said
WBE/MBE. A finding of adiscriminatory practice by -the City's MBE/WBE Utilization Board
shall prohibit that person or entity from being awarded a City contract for a period of one (1)
year from the date of such determination, and such determination may also be grounds for
terminating the contact for which the discriminatory practice or noncompliance pertains.
7. The undersigned contractor agrees that the following nondiscrimination commitment
shall be made a part of any contract which it may henceforth enter into with the City of South
Bend, Indiana or any of its agencies, boards or commissions.
Non -Collusion Non-Debannent Affidavit Non Iran Fonn
Contractor agrees not to discriminate against or intimidate any employee or applicant for
employment in the performance of this contract with privileges of employment, or any matter
directly or indirectly related to employment, because of race, religion, color, sex, gender
expression, gender identity, sexual orientation, handicap, national origin or ancestry. Breach of
this provision may be regarded as material breach of contract.
I, the undersigned bidder or agent as contractor on a public works project, understand my
statutory obligations to the use of steel products or foundry products made in the United States
(I.C. 5-16-8-1). I hereby certify that I and all subcontractors employed by me for this project will
use steel products or foundry products made in the United States on this project if awarded. I
understand I have an affirmative duty to notify the City in my bid that my proposal does not
include the use of steel products or foundry products made in the United States. I understand it is
my sole obligation and responsibility to provide a justification to the City, subject to review and
approval, why the cost of United States made steel or foundry products is unreasonable. Prior to
award and upon submission of bid which does not use steel products or foundry products made
in the United States, the City, through its director of public works, shall make a determination if
the price of United States made steel or foundry is unreasonable. I understand that violations
hereunder may result in forfeiture of contractual payments.
I hereby affirm under the penalties of perjury that the facts and information contained in the foregoing bid for
public works are true and correct.
Dated this r -*k�- day of �J6V 20,'O
Printed Name and Title
Subscribed and sworn to before me this 10 day of 1V QjJ , 20,=20
My Commission Expires 12-1Z-(O] 2,z-
Lf zk7�kL7)�4T -
III,., Notary Public
L
County of Residence
Amy 1. Durst
otary Public - State of Ohio
nmission Expires 12/26/2022
Affidavit Non Iran Form
'!/1►11111
Document A31OTM - 2010
Conforms with The American Institute of Architects AIA Document 310
Bid Bond
CONTRACTOR:
(Name, legal status and address)
Horton Emergency Vehicles LLC
3800 McDowell Road
Grove City, OH 43123
OWNER:
(Name, legal stat+rs and address)
South Bend Fire Department
1222 S. Michigan Street
South Bend, IN 46619
SURETY:
(Name, legal status and priucipul place r jburines:,9
Travelers Casualty and Surety Company of America
One Tower Square
Hartford, CT 06183
Mailing Address for Notices
13935 Bishops Drive, Suite 360
Brookfield, Wisconsin 53005
BOND AMOUNT: 10% Ten Percent of Amount Bid
PROJECT:
(,Name, location or address, and)'roJectnumber, if any)
2022 International/Horton 603 Ambulance
This document has Important
legal consequences. Consultation
with an attorney is encouraged
with respect to Its completion or
modification.
Any singular reference to
Contractor, Surety, Owner or
other party shall be considered
plural where applicable.
The Contractor and Surety arc bound to the Owncr in the amount set forth above, for the payment of which the Contractor and Surety bind
themselves, their heirs, executors, administrators, successors and assigns, jointly and severally, as provided heroin. The conditions of this
Bond are such that if the Owner accepts the bid of the Contractor within the time specified in the bid documents, or within such time period
as may be agreed to by the Owner and Contractor, and the Contractor either(l) enters into a contract with the Owner in accordance with
the terms of such bid, and gives such bond or bonds as may be specified in the bidding or Contract documents, with a surety admitted in
the jurisdiction of the project and othen%ise acceptable to the Owner, for the faithful perfomlance of such Contract and for the prompt
payment of labor and material furnished in the prosecution thereof; or (2) pays to the Owner the difference, not to exceed the amount of
this Bond, between the amount specified in said bid and such larger amount for which the Owner may in good faith contract with another
party to peribmt the wort: covered by said bid, then this obligation shall be null and void, otherwise to remain in full force and e&cl. The
Surety hereby waives any notice of rot agreement between the Owner and Contractor to extend the time in which the Owner may accept the
bid. Waiver of notice by the Surety shall not apply to any extension exceeding sixty (60) days in the aggregate beyond the time Ibr
acceptance ol'bids specif ed in the bid documents, and Elie Owner unit Contractor %hull obtain the Surety's consent for an extension beyond
sixty (60) days.
If this Bond is issued in connection with a subcontractor's bid to a Contractor, the limn Contractor in this Bond shall be doomed to be
Subcontractor and the term Owner shall be doomed to be Contractor.
When this Band ties been furnished to comply with a statutory or other legal requirement in the locution ol'the project, any provision in
this Bond conflicting with said statutory or legal requirement shall be deemed deleted herefmm unit provisions conforming to such
statutory or other legal requirement shall be deemed incorporated herein. When so furnished, the intent is that this Bond %hull be construed
as a Statutory bond and not as a common law bond.
Signed and scalcd this 5th day of November.2020.
Horton Emergency Vehicles LLC
!Principal) (Seal)
(Wluress)
By:
(Title)
1->&CI rn
11Tin,e,.,9 Lisa M. Slakes
S-00541AS 8110
Travelers Casualty and Surety Company of America
.111111111111k Travelers Casualty and Surety Company
TRAVELERS J St. Paul Fire and Marine Insurance Company
Farmington Casualty Company
POWER OF ATTORNEY
KNOW ALL MEN BY THESE PRESENTS: That Travelers Casualty and Surety Company of America, Travelers Casualty and Surety Company, St. Paul
Fire and Marine Insurance Company, and Farmington Casualty Company are corporations duly organized under the laws of the State of Connecticut
(herein collectively called the "Companies"), and that the Companies do hereby make, constitute and appoint Cathy Hutson of Milwaukee, WI
their true and lawful Attorney -in -Fact to sign, execute, seal and acknowledge any and all bonds, recognizances, conditional undertakings and other writings
obligatory in the nature thereof on behalf of the Companies in their business of guaranteeing the fidelity of persons, guaranteeing the performance of
contracts and executing or guaranteeing bonds and undertakings required or permitted in any actions or proceedings allowed by law, including the following
bond:
Surety Bond No.: Bid Bond Principal: Horton Emergency Vehicles LLC
OR Obligee: South Bend Fire Department
Project Description: 20221nlernational/Horton 603 Ambulance
IN WITNESS WHEREOF, the Companies have caused this instrument to be signed, and their corporate seals to be hereto affixed, this 6th day of May,
2019.
8860
t�D
State of Connecticut By:
obert L. Raney enior Vice President
City of Hartford ss.
On this the 6th day of May, 2019, before me personally appeared Robert L. Raney, who acknowledged himself to be the Senior Vice President of each of
the Companies, and that he, as such, being authorized so to do, executed the foregoing instrument for the purposes therein contained by signing on behalf
of said Companies by himself as a duly authorized officer. ...z
IN WITNESS WHEREOF, I hereunto set my hand and official seal.
My Commission expires the 30th day of June, 2021
Anna P. Nowik, Notary Public
This Power of Attorney is granted under and by the authority of the following resolutions adopted by the Boards of Directors of each of the Companies,
which resolutions are now in full force and effect, reading as follows:
RESOLVED, that the Chairman, the President, any Vice Chairman, any Executive Vice President, any Senior Vice President, any Vice President, any
Second Vice President, the Treasurer, any Assistant Treasurer, the Corporate Secretary or any Assistant Secretary may appoint Attorneys -in -Fact and
Agents to act for and on behalf of the Company and may give such appointee such authority as his or her certificate of authority may prescribe to sign
with the Company's name and seal with the Company's seal bonds, recognizances, contracts of indemnity, and other writings obligatory in the nature of
a bond, recognizance, or conditional undertaking, and any of said officers or the Board of Directors at any time may remove any such appointee and
revoke the power given him or her; and it is
FURTHER RESOLVED, that the Chairman, the President, any Vice Chairman, any Executive Vice President, any Senior Vice President or any Vice
President may delegate all or any part of the foregoing authority to one or more officers or employees of this Company, provided that each such delegation
is in writing and a copy thereof is filed in the office of the Secretary; and it is
FURTHER RESOLVED, that any bond, recognizance, contract of indemnity, or writing obligatory in the nature of a bond, recognizance, or conditional
undertaking shall be valid and binding upon the Company when (a) signed by the President, any Vice Chairman, any Executive Vice President, any
Senior Vice President or any Vice President, any Second Vice President, the Treasurer, any Assistant Treasurer, the Corporate Secretary or any
Assistant Secretary and duly attested and sealed with the Company's seal by a Secretary or Assistant Secretary; or (b) duly executed (under seal, if
required) by one or more Attorneys -in -Fact and Agents pursuant to the power prescribed in his or her certificate or their certificates of authority or by one
or more Company officers pursuant to a written delegation of authority; and it is
FURTHER RESOLVED, that the signature of each of the following officers: President, any Executive Vice President, any Senior Vice President, any
Vice President, any Assistant Vice President, any Secretary, any Assistant Secretary, and the seal of the Company may be affixed by facsimile to any
Power of Attorney or to any certificate relating thereto appointing Resident Vice Presidents, Resident Assistant Secretaries or Attorneys -in -Fact for
purposes only of executing and attesting bonds and undertakings and other writings obligatory in the nature thereof, and any such Power of Attorney or
certificate bearing such facsimile signature or facsimile seal shall be valid and binding upon the Company and any such power so executed and certified
by such facsimile signature and facsimile seal shall be valid and binding on the Company in the future with respect to any bond or understanding to
which it is attached.
1, Kevin E. Hughes, the undersigned, Assistant Secretary of each of the Companies, do hereby certify that the above and foregoing is a true and correct
copy of the Power of Attorney executed by said Companies, which remains in full force and effect.
Dated this 5th day of November, 2020.
A� Hughes, Assislant Secretary
To verify the authenticity of this Power of Attorney, please call us at 1-800-421.3880,
Please refer to the above -named Attorney -in -Fact and the details of the bond to which this Power of Attorney is attached.
r
7,
1316 COUNTY -CITY BUILDING PHONE 574/ 235-9251
227 W. JEFFERsoN BOULEVARD ~lf t. FAX 574/ 235-9171
SOUTH BEND, INDIANA 46601-1830 TDD 574/ 235-5567
CITY OF SOUTH BEND, JAMES MUELLER, MAYOR
BOARD OF PUBLIC WORKS
Date: November 5, 2020
To: All Plan Holders
From Linda M. Martin, Clerk, Board of Public Works _
Subject Addendum Number: 1
Project Name: Spec P - One or More 2020 or Newer Emergency Medical Vehicle
Project Number:
ACKNOWLEDGEMENT OF RECEIPT OF ADDENDUM
Date Received:
This addendum is being forwarded to you for the above referenced project.
Please sign below and acknowledge receipt of this Addendum
by faxing this sheet to the Board of Public Works at (574) 235-9171
within 48 hours of receipt. A copy MUST also be included with your
bid package upon submittal.
THIS ADDENDUM MAY AFFECT YOUR BID.
Notes:
The attached documents are hereby added to the Specifications and Contract
Documents and become a part of herein.
Company: r(Or
Authorized Signature:
Date: J i-6-
Version 4/2/2015
INTERNATIONAL"
November 05, 2020
Prepared For:
CITY OF SOUTH BEND/MV607/102 CA.2022 M.Y.
LIQUID SPRING/JEFF HUDAK
JASON CAVALLO
3800 Mcdowell Rd.
Grove City, OH 43123-
(614)539 - 8181
Reference ID: N/A
Presented By:
RUSH TRUCK CENTERS
Timothy M White
3950 PARKWEST DR
COLUMBUS OH 43228 -
(614)541-4526
Thank you for the opportunity to provide you with the following quotation on a new International truck. I am sure the following detailed
specification will meet your operational requirements, and I look forward to serving your business needs.
Model Profile
2022 MV607 SBA LP (MV60H)
AXLE CONFIG:
4X2
APPLICATION:
Rescue
MISSION:
Requested GVWR: 25500. Calc. GVWR: 22500
Calc. Start / Grade Ability: 32.86% / 2.71 % @ 55 MPH
Calc. Geared Speed: 80.3 MPH
DIMENSION:
Wheelbase: 169.00, CA: 101.90, Axle to Frame: 63.00
ENGINE, DIESEL:
(Cummins B6.7 260) EPA 2021, 260HP @ 2400 RPM, 660 lb-ft Torque @ 1600 RPM, 2600 RPM
Governed Speed, 260 Peak HP (Max)
TRANSMISSION, AUTOMATIC:
(Allison 2500 EVS) 5th Generation Controls, Wide Ratio, 6-Speed with Double Overdrive, with
PTO Provision, Less Retarder, with 33,000-lb GVW and GCW Max
CLUTCH:
Omit Item (Clutch & Control)
AXLE, FRONT NON -DRIVING:
(Dana Spicer E-10021R) I -Beam Type, 9,000-lb Capacity
AXLE, REAR, SINGLE:
(Dana Spicer 17060S) Single Reduction, 17,500-lb Capacity, 190 Wheel Ends Gear Ratio: 4.88
CAB:
Conventional, Day Cab
TIRE, FRONT:
(2) 245/70R19.5 Load Range G G647 RSS (GOODYEAR), 626 rev/mile, 75 MPH, All -Position
TIRE, REAR:
(4) 245/70R19.5 Load Range H FUEL MAX RTD (GOODYEAR), 622 rev/mile, 81 MPH, Drive
SUSPENSION, REAR, SINGLE:
(LiquidSpring) Accommodation Package for CBC/TSC Install, 13,500-lb Capacity, with Stacked
Volume Tanks Under Left Rail and Power Module Mounted Behind Suspension
PAINT:
Cab schematic 10OWP
Location 1: 2684, Rangoon Red (Custom)
Chassis schematic 936WP
Frame: 9036, Cool Gray Light (Std)
Proposal: 17172-06
INTERNATIONAL" Vehicle Specifications November05, 2020
2022 MV607 SBA LP (MV60H)
Code
Description
MV60H00
Base Chassis, Model MV607 SBA LP with 169.00 Wheelbase, 101.90 CA, and 63.00 Axle to Frame.
1570
TOW HOOK, FRONT (2) Frame Mounted
1ANA
AXLE CONFIGURATION {Navistar} 4x2
Notes
: Pricing may change if axle configuration is changed.
1 CAA
FRAME RAILS High Strength Low Alloy Steel (80,000 PSI Yield); 9.125" x 3.062" x 0.312" (231.8mm x 77.8mm
x 8.Omm); with Transition to 6.500" x 3.062" x 0.312" (165.1 mm x 77.8mm x 8.Omm); 388.4" (9864mm)
Maximum OAL, For LP Chassis
1LNN
BUMPER, FRONT Contoured, Steel, Chrome Plated
1WEH
WHEELBASE RANGE 134" (340cm) Through and Including 197" (500cm)
2AYY
AXLE, FRONT NON -DRIVING {Dana Spicer E-10021R} I -Beam Type, 9,000-lb Capacity
3AGW
SUSPENSION, FRONT, SPRING Parabolic Taper Leaf, Shackle Type, 9,000-lb Capacity, with Shock
Absorbers
Includes
: SPRING PINS Rubber Bushings, Maintenance -Free
4091
BRAKE SYSTEM, AIR Dual System for Straight Truck Applications
Includes
BRAKE LINES Color and Size Coded Nylon
DRAIN VALVE Twist -Type
GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster
PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel
PARKING BRAKE VALVE For Truck
QUICK RELEASE VALVE On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4
SPRING BRAKE MODULATOR VALVE R-7 for 4x2, SR-7 with relay valve for 6x4/8x6
4722
DRAIN VALVE {Bendix DV-21 Automatic, with Heater, for Air Tank
4AZJ
AIR BRAKE ABS {Bendix AntiLock Brake System} 4-Channel (4 Sensor/4 Modulator) Full Vehicle Wheel
Control System, with Automatic Traction Control
4EBD
AIR DRYER {Wabco System Saver 1200} with Heater
4EXP
BRAKE CHAMBERS, FRONT AXLE {Bendix} 20 Sgln
4EXS
BRAKE CHAMBERS, REAR AXLE {Bendix EverSure} 24/30 Sqln Spring Brake
4LAG
SLACK ADJUSTERS, FRONT {Gunite} Automatic
4LGG
SLACK ADJUSTERS, REAR {Gunite} Automatic
4SPA
AIR COMPRESSOR {Cummins} 18.7 CFM
4VGA
AIR DRYER LOCATION Mounted Outside Right Rail, Forward of Front Wheel
4VKH
AIR TANK LOCATION (2) Mounted Under Battery Box, Outside Right Rail, Under Cab
4XDD
BRAKES, FRONT {Meritor 15X5 Q-PLUS CAST) Air S-Cam Type, Cast Spider, Fabricated Shoe, Double
Anchor Pin, Size 15" X 5", 13,200-lb Capacity
4XDU
BRAKES, REAR {Meritor 15X8.625 Q-PLUS CAST) Air S-Cam Type, Cast Spider, Fabricated Shoe, Double
Anchor Pin, Size 15" X 8.625", 21,000-lb Capacity per Axle
5710
STEERING COLUMN Tilting and Telescoping
5CAW
STEERING WHEEL 4-Spoke; 18" Dia., Black
2 Proposal: 17172-06
INTERNATIONAL" Vehicle Specifications November05, 2020
2022 MV607 SBA LP (MV60H)
Code
Description
5PSA
STEERING GEAR {Sheppard M100) Power
6DGA
DRIVELINE SYSTEM (Dana Spicer) SPL100, for 4x2/6x2
7BME
EXHAUST SYSTEM Horizontal Aftertreatment System, Frame Mounted Under Right Rail Back of Cab,
Includes Single Short Horizontal Tail Pipe
7SCP
ENGINE EXHAUST BRAKE for Cummins ISB/B6.7/ISL/L9 Engine with Variable Vane Turbo Charger
7WZX
SWITCH, FOR EXHAUST 3 Position, Momentary, Lighted Momentary, ON/CANCEL, Center Stable, INHIBIT
REGEN, Mounted in IP Inhibits Diesel Particulate Filter Regeneration When Switch is Moved to ON While
Engine is Running, Resets When Ignition is Turned OFF
8000
ELECTRICAL SYSTEM 12-Volt, Standard Equipment
Includes
DATA LINK CONNECTOR For Vehicle Programming and Diagnostics In Cab
HAZARD SWITCH Push On/Push Off, Located on Instrument Panel to Right of Steering Wheel
HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever
PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light
STARTER SWITCH Electric, Key Operated
STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector
TURN SIGNAL SWITCH Self -Cancelling for Trucks, Manual Cancelling for Tractors, with Lane Change
Feature
: TURN SIGNALS, FRONT Includes Reflectors and Auxiliary Side Turn Signals, Solid State Flashers; Flush
Mounted
: WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature (5 Pre -Set Delays), Integral with
Turn Signal Lever
WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted
WIRING, CHASSIS Color Coded and Continuously Numbered
8518
CIGAR LIGHTER Includes Ash Cup
8541
HORN, ELECTRIC (2) Disc Style
8585
FOG LIGHTS Prewire; Includes Auxiliary Switch and Wiring to Front Bumper, for Driving Lights or Fog Lights
Mounted by Customer
8GXK
ALTERNATOR {Leece-Neville BLP4006HN) Brushless, 12 Volt, 325 Amp Capacity, Pad Mount, with Remote
Sense
8HAB
BODY BUILDER WIRING Back of Day Cab at Left Frame or Under Sleeper, Extended or Crew Cab at Left
Frame; Includes Sealed Connectors for Tail/Amber Turn/Marker/ Backup/Accessory Power/Ground and
Sealed Connector for Stop/Turn
8MJU
BATTERY SYSTEM {Fleetrite} Maintenance -Free, (3) 12-Volt 285OCCA Total, Top Threaded Stud
8RMZ
SPEAKERS (2) 6.5" Dual Cone Mounted in Both Doors, (2) 5.25" Dual Cone Mounted in Both B-Pillars
8RPU
RADIO AM/FM/WB/SiriusXM/Clock/Bluetooth/USB Input/Auxiliary Input
8THV
DISCONNECT, FRONT HARNESS for Guide Post Lights; Connectors Located at Headlight Connection, for
Customer Installation
8VTV
STOP -LIGHT WIRING MODIFIED Stop -Lights Turned on When Engine Compression Brake, Exhaust Brake
or Retarder is Activated
8VUX
BATTERY BOX Steel, with Plastic Cover, 25" Wide, 2-3 Battery Capacity, Mounted Right Side Under Cab
8WBW
JUMP START STUD Remote Mounted
Includes
: JUMP START STUD Mounted to Battery Box
Proposal: 17172-06
INTERNATIONAL" Vehicle Specifications November05, 2020
2022 MV607 SBA LP (MV60H)
Code Description
8WGL WINDSHIELD WIPER SPD CONTROL Force Wipers to Slowest Intermittent Speed When Park Brake Set and
Wipers Left on for a Predetermined Time
8WHE HORN, AIR Accommodation Package, Less Horn
8WPB HEADLIGHTS Halogen, Composite Aero Design, with Daytime Running Lights
8WPH CLEARANCE/MARKER LIGHTS (5) {Truck Lite} Amber LED Lights, Flush Mounted on Cab or Sunshade
8WPZ TEST EXTERIOR LIGHTS Pre -Trip Inspection will Cycle all Exterior Lamps Except Back-up Lights
8WRB HEADLIGHTS ON W/WIPERS Headlights Will Automatically Turn on if Windshield Wipers are turned on
8WTK STARTING MOTOR {Delco Remy 38MT Type 300} 12 Volt, Less Thermal Over -Crank Protection
8WWJ INDICATOR, LOW COOLANT LEVEL with Audible Alarm
8WZP
INDICATOR, BATTERY WARNING Green BATTERY ON Indicator, Mounted on Left Side of Instrument Panel,
To be Used with Factory Installed or Customer Mounted Battery Disconnect Switch
8XAH
CIRCUIT BREAKERS Manual -Reset (Main Panel) SAE Type III with Trip Indicators, Replaces All Fuses
8XGT
TURN SIGNALS, FRONT Includes LED Side Turn Lights Mounted on Fender
8XHV
BATTERY DISCONNECT SWITCH for Cab Power Disconnect Switch, Disconnects Power to Power
Distribution Center (PDC) and Body Builder Through Solenoid, Does Not Disconnect Charging Circuits, Locks
with Padlock, Cab Mounted
8XKM
SWITCH, AIR HORN, PASSENGER Fire Truck Application; Momentary Switch Located in Instrument Panel
Close to Passenger, Driver Also To Activate Switch with Lanyard
8XKY
USB PORT (1) Located in the Instrument Panel
9AAB
LOGOS EXTERIOR Model Badges
9AAE
LOGOS EXTERIOR, ENGINE Badges
9HBM
GRILLE Stationary, Chrome
9WAY
FRONT END Tilting, Fiberglass, with Three Piece Construction
9WBT
GRILLE EMBER SCREEN Mounted to Grille and Cowl Tray to Keep Hot Embers out of Engine and HVAC Air
Intake System
10060
PAINT SCHEMATIC, PT-1 Single Color, Design 100
Includes
: PAINT SCHEMATIC ID LETTERS "WP"
10636
PAINT IDENTITY, PT-2 Single Color, Instruction No. 936. Frame/Running Gear, Less Fuel Tanks
Includes
: NOTE: Battery Box, Air Tanks, Fuel Tanks, Steps and Straps NOT Painted
10761
PAINT TYPE Base Coat/Clear Coat, 1-2 Tone
10771
PAINT CLASS Single Custom Color
10VAA
KEYS - ALL ALIKE, ADDITIONAL 3 Keys
11001 CLUTCH Omit Item (Clutch & Control)
12703 ANTI -FREEZE Red, Extended Life Coolant; To -40 Degrees F/ -40 Degrees C, Freeze Protection
12ERJ ENGINE, DIESEL {Cummins B6.7 2601 EPA 2021, 260HP @ 2400 RPM, 660 lb-ft Torque @ 1600 RPM, 2600
RPM Governed Speed, 260 Peak HP (Max)
12TSY FAN DRIVE {Borg-Warner SA85} Viscous Type, Screw On
4 Proposal: 17172-06
INTERNATIONAL" Vehicle Specifications November05, 2020
2022 MV607 SBA LP (MV60H)
Code
Description
Includes
: FAN Nylon
12UYE
RADIATOR Aluminum, 2-Row, Cross Flow, Over Under System, 717 Sqln Louvered, with 313 Sqln Charge
Air Cooler, Includes In -Tank Oil Cooler
Includes
DEAERATION SYSTEM with Surge Tank
HOSE CLAMPS, RADIATOR HOSES Gates Shrink Band Type; Thermoplastic Coolant Hose Clamps
RADIATOR HOSES Premium, Rubber
12VBR
AIR CLEANER with Service Protection Element
12VHP
FEDERAL EMISSIONS {Cummins B6.7} EPA, OBD and GHG Certified for Calendar Year 2021
12VXT
THROTTLE, HAND CONTROL Engine Speed Control; Electronic, Stationary, Variable Speed; Mounted on
Steering Wheel
12WPV
OIL PAN 15 Quart Capacity, For Cummins ISB/B6.7 Engines
12WZE
EMISSION COMPLIANCE Federal, Does Not Comply with California Clean Air Idle Regulations
12XAT
ENGINE CONTROL, REMOTE MOUNTED Provision for; Includes Wiring for Body Builder Installation of PTO
Controls, with Ignition Switch Control, for Cummins ISB/B6.7 and ISL/L9 Engines
13ASY
TRANSMISSION, AUTOMATIC {Allison 2500 EVS} 5th Generation Controls, Wide Ratio, 6-Speed with Double
Overdrive, with PTO Provision, Less Retarder, with 33,000-lb GVW and GCW Max
13WLN
TRANSMISSION OIL Synthetic; 20 thru 28 Pints
13WVS
TRANSMISSION SHIFT CONTROL T-Handle
13WYH
TRANSMISSION TCM LOCATION Located Inside Cab
13WYY
SHIFT CONTROL PARAMETERS {Allison} 1000 or 2000 Series Transmissions, Performance Programming
13XAN
PTO LOCATION Customer Does Not Intend to Install PTO
14AGE
AXLE, REAR, SINGLE {Dana Spicer 17060S} Single Reduction, 17,500-lb Capacity, 190 Wheel Ends. Gear
Ratio: 4.88
14TDR
SUSPENSION, REAR, SINGLE {LiquidSpring} Accommodation Package for CBC/TSC Install, 13,500-lb
Capacity, with Stacked Volume Tanks Under Left Rail and Power Module Mounted Behind Suspension
15LMS
FUEL/WATER SEPARATOR 12 VDC Electric Heater, Includes Pre -Heater, Includes Water -in -Fuel Sensor,
Cummins Supplied on Engine
15SWU
FUEL TANK Top Draw, Non -Polished Aluminum, D-Style, 16" Tank Depth, 40 US Gal (151 L), Mounted Left
Side, Under Cab
15WDG
DEF TANK 7 US Gal (26L) Capacity, Frame Mounted Outside Left Rail, Under Cab
16030
CAB Conventional, Day Cab
Includes
: CLEARANCE/MARKER LIGHTS (5) Flush Mounted
16136
AIR CONDITIONER, PROVISION FOR Accommodation Package, for Air Conditioning, Includes Auxiliary
Compressor in Secondary Position and Compressor Drive Effects for Vehicle with Primary Compressor
Mounting
16564
HEATER SHUT-OFF VALVES (1) Ball Valve Type, Supply Line
16BAM
AIR CONDITIONER with Integral Heater and Defroster
5 Proposal: 17172-06
INTERNATIONAL"
Vehicle Specifications November 05, 2020
2022 MV607 SBA LP (MV60H)
Code
Description
16GDG
GAUGE CLUSTER Premium Level; English with English Speedometerand Tachometer, for Air Brake Chassis,
Includes Engine Coolant Temperature, Primary and Secondary Air Pressure, Fuel and DEF Gauges, Oil
Pressure Gauge, Includes 5 Inch LCD Color Display
16HGH
GAUGE, OIL TEMP, AUTO TRANS for Allison Transmission
16HHE
GAUGE, AIR CLEANER RESTRICTION {Filter -Minder} with Black Bezel, Mounted in Instrument Panel
16HKT
IP CLUSTER DISPLAY On Board Diagnostics Display of Fault Codes in Gauge Cluster
16JNT
SEAT, DRIVER {National 20001 Air Suspension, High Back with Integral Headrest, Vinyl, Isolator, 1 Chamber
Lumbar, with 2 Position Front Cushion Adjust, -3 to +14 Degree Angle Back Adjust
16RPV
SEAT, PASSENGER {National 2000} Air Suspension, High Back with Integral Headrest, Vinyl, Isolated, 1
Chamber Lumbar, 2 Position Front Cushion Adjustment, -3 to +14 Degree Back Adjust
16SDC
GRAB HANDLE, EXTERIOR (2) Chrome, Towel Bar Type, with Anti -Slip Rubber Inserts, for Cab Entry
Mounted Left and Right Side at B-Pillar
16SNN
MIRRORS (2) C-Loop, Heated, Bright Heads, Black Arms, 7.5" x 14" Flat Glass, Includes 7.5" x 7" Convex
Mirrors, for 102" Load Width
Notes
: Mirror Dimensions are Rounded to the Nearest 0.5"
16VCC
SEAT BELT All Orange; 1 to 3
16VKK
CAB INTERIOR TRIM Diamond, for Day Cab
Includes
: CONSOLE, OVERHEAD Molded Plastic with Dual Storage Pockets, Retainer Nets and CB Radio Pocket;
Located Above Driver and Passenger
: DOME LIGHT, CAB Door Activated and Push On -Off at Light Lens, Timed Theater Dimming, Reading Lights;
Integral to Overhead Console, Center Mounted
: SUN VISOR (3) Padded Vinyl; 2 Moveable (Front -to -Side) Primary Visors, Driver Side with Vanity Mirror and
Toll Ticket Strap, plus 1 Auxiliary Visor (Front Only), Driver Side
16VLM
CAB REAR SUSPENSION Rubber Suspension, for Low Cab Height
16WBY
ARM REST, RIGHT, DRIVER SEAT
16WBZ
ARM REST, LEFT, PASSENGER SEAT
16WHJ
HOSE CLAMPS, HEATER HOSE {Breeze} Belleville Washer Type
16WJU
WINDOW, POWER (2) and Power Door Locks, Left and Right Doors, Includes Express Down Feature
16WKZ
KEYLESS ENTRY SYSTEM REMOTE with Panic and Auxiliary Buttons, Includes One Key Fob (Transmitter)
16WSE
LOW WASHER FLUID INDICATOR
16XJN
INSTRUMENT PANEL Flat Panel
16ZBT
ACCESS, CAB Steel, Driver & Passenger Sides, Two Steps per Door, for use with Day Cab and Extended
Cab
27DAY
WHEELS, FRONT {Accuride 296851 DISC; 19.5x7.50 Rims, Extra Polish Aluminum, 10-Stud, 285.75mm BC,
Hub -Piloted, Flanged Nut, with Steel Hubs
28DAY
WHEELS, REAR {Accuride 29685} DUAL DISC; 19.5x7.50 Rims, Extra Polish Aluminum Outer Wheel 10-Hand
Hole, Steel Inner Wheel 5-Hand Hole, 10-Stud, 285.75mm BC, Hub -Piloted, Flanged Nut, with Steel Hubs
29580
WHEEL SEALS, FRONT {International} Oil -Lubricated Wheel Bearings
29SAK
WHEEL SEALS, REAR {Stemco Discover-HNBR} Oil Lubricated Wheel Bearings
6 Proposal: 17172-06
INTERNATIONAL" Vehicle Specifications November05, 2020
2022 MV607 SBA LP (MV60H)
Code
60ACW
7749450101
7789458137
40129
40PTL
40SZX
1
TSC
TSC
Description
BDY INTG, 1/0 EXP HARNESS {for Diamond Logic Builder) In -Cab wire harness (DLB) program only, Includes
a harness with five blunt cut wires routed on lower left of instrument panel. Two ground active inputs and two
(.5Amp) relay drivers outputs are provided
(2) TIRE, FRONT 245/70R19.5 Load Range G G647 RSS (GOODYEAR), 626 rev/mile, 75 MPH, All -Position
(4) TIRE, REAR 245/70R19.5 Load Range H FUEL MAX RTD (GOODYEAR), 622 rev/mile, 81 MPH, Drive
Services Section:
WARRANTY Standard for MV Series, Effective with Vehicles Built July 1, 2017 or Later, CTS-2020A
SRV CONTRACT, EXT VEH COVERAGE {Navistar) To 36-Month/50,000 Miles (80,000 km), Excludes
Extended Warranty for Engine and Transmission
SRV CONTRACT, EXT CMMS ENGINE {Cummins) To 72-Month/100,000 Miles (160,000 km), Extended
Cummins B6.7 Engine Coverage, Full Engine Coverage, (RV/Fire Application Only)
TO ADD LIQUID SPRING 13500 REAR SUSPENSION
$8600.00
GROVER/HADLEY AIR HORNS MTD ON HOOD
SPECIAL PROGRAMMING
AUXILIARY AIR TANK FOR HORNS
FRONT STABILIZER BAR
CONTINUE EXHAUST TO LR WHEEL AREA
ADDITIONAL KEY FOB
LIQUID SPRING SUSPENSION
7
Proposal: 17172-06
INTERNATIONAL" Weight Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
There is no weight study for this proposal.
Proposal: 17172-06
INTERNATIONAL" Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
3000
E 2500
a
2000
m
CCL 1500
m
1000
"' 500
0
ENGINE/TRANSMISSION MATCHING
Sawtooth Grid
Vehicle Speed (mph)
Marginal Operating Power Below Recommended Minimum
Governed Engine Speed (2600) 90%Operating Range i1792}
85% Operating Range (1654) Actual Vehicle Po-,ver
Sawtooth Details
Gear
Trans
Upshift Power Avail
Govern Power Avail
Peak Power Comparison Warn Msg
Ratio
Veh Spd
Eng Spd
Veh Spd
Eng Spd Gear Step
85% Range
90% Range
(MPH)
(RPM)
(MPH)
(RPM)
(%)
(%)
(%)
1 C
3.51
0.0
2313
11.0
2419
N/A
57
45
2C
1.90
11.0
2301
18.1
2362
N/A
57
45
2L
1.90
18.1
1740
25.5
2455
N/A
57
45
3L
1.44
25.5
1860
33.7
2452
N/A
57
45
4L
1.00
33.7
1703
48.4
2450
N/A
57
45
5L
0.74
48.4
1813
65.1
2437
N/A
57
45
6L
0.64
65.1
2108
80.3
2600
N/A
57
45
@ - WHEELSLIP CAN OCCUR AT THE GRADE SHOWN. THE VEHICLE IS CAPABLE OF INCREASED GRADEABILITY IF MORE
WEIGHT IS PLACED ON THE DRIVE AXLES.
9 Proposal: 17172-06
INTERNATIONAL" Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
STEADY STATE PERFORMANCE
Performance Results Gear
Veh Spd
Eng Spd
Fuel Econ
Grade Notes
(mph)
(rpm)
(mpg)
(%)
LEVEL ROAD MAXIMUM SPEED 6L
77.1
2495
5.93
0.00
HI GEAR SPEED @ RATED RPM ----
----
----
----
----
55.0 MPH STEADY-STATE 6L
55.0
1781
10.05
2.71
TYPICAL OPERATING SPEED 6L
58.0
1878
9.41
2.52 - Calculated Grade
Ability/Fuel Economy
VEHICLE ORDER CODING ERRORS MAY RESULT IF THE
"LEVEL ROAD
MAX SPEED" VALUE EXCEEDS THE "HI GEAR SPEED
@ RATED RPM" AND IS USED AS THE ENGINE PROGRAMMABLE VEHICLE
SPEED LIMIT.
IF THE RESULTS CONTAIN " -----" , VEHICLE CANNOT ATTAIN THAT SPEED.
IF THE RESULTS CONTAIN "*"', THE ENGINE USED DOES NOT HAVE A FUEL MAP. FUEL ECONOMY CANNOT BE PREDICTED
Recommendations / General Information
IDLE FUEL RATE: 0.53 GALS/HR @ 700.0 RPM
TORQUE CONVERTER: TC-221 STALL RATIO: 1.73
Fuel Economy Route: Normal Route - City, Suburban, and Highway
Key Fuel Economy Information
City
Suburban
Highway Notes
MILES PER GALLON
8.74
10.93
9.54
AVERAGE MPH
19.1
40.0
54.6
MISSION MINUTES
29.52
51.71
173.28
IF THE RESULTS CONTAIN —, THE ENGINE USED DOES NOT HAVE A FUEL MAP. FUEL ECONOMY CANNOT BE PREDICTED.
10 Proposal: 17172-06
INTERNATIONAL" Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
GRADEABILITY PERFORMANCE
Enroute - Full Throttle Upshift Performance
Gear
Trans
Veh Spd
Eng Spd
Whl Pwr
Grade
Warn Notes
Ratio
(mph)
(rpm)
(hp)
(%)
Msg
1 C
3.51
0.0
2313
0.00
48.04
@ STALL
6.7
2309
158.84
36.30
70% EFF
8.3
2325
181.21
32.86
80% EFF
11.0
2419
200.30
27.02
2C
1.90
11.0
2301
146.32
19.19
18.1
2362
195.06
15.13
2L
1.90
18.1
1740
192.55
14.92
25.5
2455
223.12
11.87
3L
1.44
25.5
1860
205.16
10.81
33.7
2452
222.31
8.41
4L
1.00
33.7
1703
189.45
6.96
48.4
2450
223.01
4.77
5L
0.74
48.4
1813
195.63
3.94
65.1
2437
215.85
1.82
69.3
2593
206.15
1.00
6L
0.64
65.1
2108
216.09
1.83
70.9
2296
216.74
1.00
74.2
2402
214.82
0.50
77.1
2495
209.79
0.00
LEVEL ROAD
80.3
2600
202.51
-0.58
RATED RPM
STARTING / TOP GEAR PERFORMANCE
Gear Trans Veh Spd Eng Spd
Whl Pwr
Grade Warn Notes
Ratio (mph) (rpm)
(hp)
(%) Msg
1 C 3.51 0.0
0.00
48.04 @ STALL
8.3
181.21
32.86 80% EFF - Calculated Start Ability
@ - WHEELSLIP CAN OCCUR AT THE GRADE SHOWN. THE VEHICLE IS CAPABLE OF INCREASED GRADEABILITY IF MORE
WEIGHT IS PLACED ON THE DRIVE AXLES.
THE TRANSMISSION WAS SIMULATED IN PERFORMANCE OPERATING MODE.
11 Proposal: 17172-06
INTERNATIONAL Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
ACCELERATION PERFORMANCE RESULTS
Acceleration Performance Grid
Acceleration Performance Grid
- - - - - - ---T------------------ - - - - - - -------------------
Q
1------- 100 ❑f
m
aCD
CD
is
------f------------ ---i---------------h---------f------- m
0 10 15 25
Time (secs)
- Vehicle Speed - Distance
Acceleration Performance: TIME TO ACCELERATE ON A GRADE TO 55.0 (MPH) IS 29.23 (SECS)
Acceleration Performance Details
Gear
Time
Distance
Speed Notes
(secs)
(feet)
(mph)
1 C
0.12
0.1
1.0
0.23
0.3
2.0
0.35
0.8
3.0
0.47
1.4
4.0
0.59
2.2
5.0
0.71
3.2
6.0
0.85
4.5
7.0
0.99
6.0
8.0
1.14
7.9
9.0
1.30
10.1
10.0
2C
1.47
12.7
11.0
1.72
17.0
12.0
1.98
21.7
13.0
2.24
26.9
14.0
2.52
32.7
15.0
2.80
39.0
16.0
3.08
46.0
17.0
3.38
53.7
18.0
2L
3.43
54.8
18.1
3.75
63.6
19.1
4.07
72.9
20.1
4.40
82.7
21.1
4.73
93.3
22.1
5.07
104.7
23.1
5.44
117.3
24.1
5.82
131.0
25.1
3L
5.99
137.4
25.5
6.43
154.1
26.5
6.86
171.4
27.5
7.31
189.8
28.5
7.77
209.4
29.5
8.25
230.4
30.5
12 Proposal: 17172-06
INTERNATIONAL" Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
Gear Time
Distance
Speed Notes
(secs)
(feet)
(mph)
8.74
252.9
31.5
9.26
277.1
32.5
9.80
303.3
33.5
4L 9.87
306.7
33.7
10.54
340.3
34.7
11.21
375.1
35.7
11.89
411.1
36.7
12.57
448.4
37.7
13.26
486.9
38.7
13.96
526.7
39.7
14.66
568.4
40.7
15.39
612.3
41.7
16.14
658.7
42.7
16.91
707.7
43.7
17.72
759.6
44.7
18.55
815.0
45.7
19.42
874.0
46.7
20.34
937.1
47.7
5L 21.07
988.5
48.4
22.25
1073.4
49.4
23.45
1161.4
50.4
24.67
1252.5
51.4
25.91
1346.9
52.4
27.17
1444.8
53.4
28.47
1547.3
54.4
29.23
1608.6
55.0
13 Proposal: 17172-06
INTERNATIONAL" Performance TCAPE Summary November 05, 2020
2022 MV607 SBA LP (MV60H)
REQUIRED TCAPE INFORMATION
TCAPE Factors For Vehicle
Selected Rear Axle Gear Ratio(s):
4.88
Engine Fan Type:
VISCOUS
Parked PTO:
NO
Enroute PTO:
NO
ID Wheel Slip Conditions:
Yes
Road Governor/Cruise Ctrl:
No
Road Surface Type:
TYPICAL
Fuel Economy Route:
Normal Route - City, Suburban, and Highway
Vehicle Vocation:
GENERAL ON HIGHWAY
Acceleration Grade (%):
0.0
Frontal Area (FT2):
96
Speed Limit on Route (MPH):
61.0
Relative Drag Coefficient:
85
Alternator (A):
40
Steering Gear (HP):
2.60
Air Conditioner (HP):
3.20
Vehicle Width (IN):
96
Vehicle Height (IN):
144
Weight on Drive Axle (LBF):
17500
Acceleration Vehicle Spd (MPH):
55.0
Air Compressor (HP):
2.20
TIRE, FRONT
2 - RADIAL LOWPROFILE
TIRE, REAR
4 - RADIAL LOWPROFILE
Components
0001ANA AXLE CONFIGURATION {Navistar} 4x2
0002AYY AXLE, FRONT NON -DRIVING {Dana Spicer E-10021R} I -Beam Type, 9,000-lb Capacity
0004SPA AIR COMPRESSOR {Cummins} 18.7 CFM
0005PSA STEERING GEAR {Sheppard M100) Power
0008GXK ALTERNATOR {Leece-Neville BLP4006HN} Brushless, 12 Volt, 325 Amp Capacity, Pad Mount, with Remote Sense
0012ERJ ENGINE, DIESEL {Cummins B6.7 2601 EPA 2021, 260HP @ 2400 RPM, 660 lb-ft Torque @ 1600 RPM, 2600 RPM
Governed Speed, 260 Peak HP (Max)
0012TSY FAN DRIVE {Borg-Warner SA85} Viscous Type, Screw On
0013ASY TRANSMISSION, AUTOMATIC {Allison 2500 EVS} 5th Generation Controls, Wide Ratio, 6-Speed with Double
Overdrive, with PTO Provision, Less Retarder, with 33,000-lb GVW and GCW Max
0014AGE AXLE, REAR, SINGLE {Dana Spicer 17060S} Single Reduction, 17,500-lb Capacity, 190 Wheel Ends
0016030 CAB Conventional, Day Cab
0016BAM AIR CONDITIONER with Integral Heater and Defroster
07749450101 TIRE, FRONT 245/70R19.5 Load Range G G647 RSS (GOODYEAR), 626 rev/mile, 75 MPH, All -Position 245/70R19.5
Load Range G G647 RSS (GOODYEAR), 626 rev/mile, 75 MPH, All -Position
07789458137 TIRE, REAR 245/70R19.5 Load Range H FUEL MAX RTD (GOODYEAR), 622 rev/mile, 81 MPH, Drive 245/70R19.5
Load Range H FUEL MAX RTD (GOODYEAR), 622 rev/mile, 81 MPH, Drive
TCAPE HAS BEEN DESIGNED TO GIVE ECONOMY AND PERFORMANCE PREDICTIONS WHICH HAVE BEEN SHOWN TO BE
TYPICAL FOR MOST OPERATIONS. HOWEVER, DUE TO OPERATING CONDITIONS, DRIVER INFLUENCES, AND OTHER
FACTORS, YOUR RESULTS MAY VARY FROM THOSE PREDICTED. ALSO, BECAUSE OF FUEL MAPPING PROCEDURES USED
BY VARIOUS ENGINE MANUFACTURERS, COMPARISONS OF FUEL ECONOMY RESULTS FOR DIFFERENT BRANDS OF
ENGINES MAY VARY FROM THOSE SHOWN.
NAVISTAR, INC. SHALL NOT BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS OR
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND THAT ARE INCURRED BY DEALER OR BY
DEALER'S CUSTOMERS AS A RESULT OF RELIANCE ON TCAPE, WHETHER THE CLAIM IS IN CONTRACT,TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE.
14 Proposal: 17172-06
INTERNATIONAL" Turning Radius Summary November05, 2020
2022 MV607 SBA LP (MV60H)
f�
'�4x�
f
k
}�\ k
y
� f
f F
k k
x 5
/
f
5 5
1 f
� r
s 1
5 i
rr J
� 4
I
CENTER
I
I
'
Turning
I I
Radius:
I
I '
Curb
I I
w
iY
�
Clearance: �
I
I I
wall
I
'
�
Clearance: �� �
I I
i i
I I TRCR
CI
TW
C
4
CH: O6 TR: ?3' S" TW: 5.54
Series:
MV
Model:
MV60H
Description:
MV607 SBA LP
Model Year:
2022
Calculation Factors
Wheelbase: 169
Front Axle: 0002AYY
Description: AXLE, FRONT NON -DRIVING, {Dana Spicer E-10021R) (-
Beam Type, 9,000-lb Capacity
Front Wheel: 0027DAY
Description: WHEELS, FRONT, {Accuride 296851 DISC; 19.5x7.50 Rims,
Extra Polish Aluminum, 10-Stud, 285.75mm BC, Hub -
Piloted, Flanged Nut, with Steel Hubs
Front Tire: 07749450101
Description: TIRES, 245/70R19.5 Load Range G G647 RSS
(GOODYEAR), 626 rev/mile, 75 MPH, All -Position
Steering Gear: 0005PSA
Description: STEERING GEAR, {Sheppard M100) Power
Turnina Radius Statistics
General Information
Inside Turn Angle:
50 Degrees
Radial Overhang:
19
Axle Information
KingPin Inclination:
5.5 Degrees
KingPin Center:
69
Turnina Radius - Curb View
C
- Curb Contact Length:
13.68
Cl
- Curb Clearance Increment:
5.07
CR
- Curb Clearance Radius:
24'2"
CH
- Curb Height:
6"
TR
- Turning Radius:
23'9"
TW
- Tire Width:
09.50
* All Measurements are in inches, unless otherwise specified.
This information is based on engineering information available at this time. Actual figures may vary. Navistar, Inc. cannot accept
liability for consequences due to this variance.
15 Proposal: 17172-06
INTERNATIONAL" Body Allied/Equipment November 05, 2020
2022 MV607 SBA LP (MV60H)
Description
TO ADD LIQUID SPRING 13500 REAR SUSPENSION
$8600.00
(US DOLLAR)
Price
$0.00
Total Body Allied/Equipment: $0.00
16 Proposal: 17172-06
EHorton
2L1-'GR0UP
SALES AGREEMENT
PROPOSAL
3800 McDowell Road Phone 614-539-8181 Horton Emergency Vehicles is Pleased to offer
Grove City, Ohio 43123 Fax this Custom Vehicle Quotation for Your Consideration
—Hortonambulance.com E-mail
DATE: 11/9/2020
Contact Name
Department Name Chy of South Bend
Street address 1222 South Michigan St
Chy, ST ZIP South Bend, IN 46619
Res Ph#
Cell#
Bus Ph#
Fax#
STANDARD EQUIPMENT
See Specifications and Drawinus for Details
QTY MAKE
CHASSIS MODEL
COLOR HORTON MODEL
VIN
HORTON JOB NUMBER
GVW
1 Int
MV
Red 603A
NIA
05904
22,500
EQUIPMENT
Base Unit Cost:
Chassis Cost
$175,810.00
$90,700.00
LINE ITEM
QTY
DESCRIPTION
UNIT PRICE
AMOUNT
1
1
2022 Int. MV Chassis with Horton 603A Medic Conversion per quote #5904.
266,510.00
266,510.00
Trade (If applicable)
NIA
NIA
Delivery
NIA
N/A
Terms: FOB Grove City, Ohio
Make all checks payable to Horton Emergency Vehicles
If you have any questions, please feel free to contact us.
THANK YOU FOR YOUR BUSINESS!
TOTAL 266,510.00
The proposed vehicle(s) will be delivery ready within 225-250 calendar days after receipt of approved production order subject to the terms an
NOTE: All customers to register their vehicles with their respective local Department of Motor Vehicles
and pay any applicable sales tax at that time. Vehicle(s) will be delivered with Certificates of Origin and an odometer statement.
WARRANTY:
Contract includes all published warranties in force at the date this proposal is accepted.
TERMS AND CONDITIONS:
A. LABOR AND MATERIALS: Horton Ambulance shall furnish the Ambulance listed as specified, with the price and delivery quoted herein, are
based on materials which were in our inventory and in the inventory of our suppliers at the time of this proposal and are subject to prior sale.
Delivery quotes are contingent on timely confirmation from Customer. Any variations to material listed will result in a cost change.
Change Order Fees may apply
B. ARBITRATION: if any controversy or dispute arises under, out of, or in relation to any of the provisions hereof which cannot be settled by
the parties within 15 days after the same shall arise, such controversy or dispute shall be submitted for arbitration in the State of Ohio in
accordance with the rules of the American Arbitration Association. Such arbitrator(s) in accordance with such rules shall
determine any dispute or controversy submitted to arbitration in accordance with the provisions of the section.
The arbitrator(s) may award any relief which he or she shall deem proper in the circumstances, without regard to the relief which
would otherwise be available to any party hereto in a court of law or equity including, without limitation, an award of money damages, specific
performance, injunctive relief and/or declaratory relief. The award and findings of the arbitrators shall be conclusive and binding upon all the
parties hereto, whether or not all parties hereto participate in the arbitration proceeding, and judgment upon the award may be entered in any
court of competent jurisdiction upon the application of any party.
Any party may initiate an arbitration proceeding hereunder, all costs of which (including fling fees, fees payable to arbitrators, court
reporters' fees, transcript costs and counsel fees) shall be recovered by the prevailing party. No party hereto shall commence any arbitration
proceeding hereunder other than in good faith, or take any action other than in good faith which requires another party hereto to commence
such arbitration hearing and, in the event any party is determined in arbitration to have so acted other than in good faith, he or it shall bear all
costs of the such proceeding.
C. REPRESENTATION OF SOLVENCY: Buyer represents that buyer is solvent and has assets sufficient to meet all of its financial obligations,
and that it is current on all of its financial obligations. Buyer further represents that it can and will meet all its financial obligations to seller on
time. Buyer understands seller relies on this promise and that any breach is material and substantial and to the essence of the contract.
D. FORCE MAJEURE: Seller shall not be responsible for delay, nondelivery, failure to complete installation or construction, or default in
shipment or other performance, in whole or in part if occasioned by strike, war, riot, or revolutions, or for any delay in transportation due to
demands or embargoes of the United States government or any other government, or nondelivery or delays through fire, floods, droughts,
accidents, insurrections, lockouts, breakdown of machinery, commandeering of vessels carrying goods, or for loss or damage in transit, or
detention of or delay in vessels resulting directly or indirectly from acts of God, perils of the sea, stoppage of labor, shortage of carriers, or
refusal of any necessary license of government restrictions considered as "force majeure," or any other unavoidable cause other than seller's
own negligence. In no case shall seller be responsible after delivery of goods in good order or conditioning to the carrier or carriers at the point
of shipment.
E. CUSTOM ORDERS: Buyer understands that a custom -ordered vehicle is speck to Buyers needs. Any deposit received for a custom order
is non-refundable once Engineering has begun, material has been purchased or the vehicle begins production.
YOU MAY CONSIDER THE PRICE QUOTED FIRM FOR WRITTEN ACCEPTANCE WITHIN 30 DAYS OF THE DATE OF OUR PROPOSAL.
Thank you for your interest in having Horton Ambulance provide you with our quotation for this
purchase. If you have any questions or commen garding this sales agreement please contact us.
Sincerely, E'
Jason Cavallo
Horton Am a, e
ACCEPTANCE OF PROPOSAL:
I have read, understand and agree to the terms, conditions and specifications described herein and
authorize Horton Emergency Vehicles to go forward with this order.
By:
Customer Signature Date
November 9, 2020
_ Horton
EMERGENCY VEHICLES
Quote # Q0000000O5904
Production #
Document Rev. #
Prepared For:
SOUTH BEND FIRE DEPARTMENT
1222 SOUTH MICHIGAN STREET
SOUTH BEND,
INDIANA
46619
Phone:
PRELIMINARY BUILD SPECIFICATION
Presented By:
Jason Cavallo
Horton Emergency Vehicles
3800 McDowell Road
Grove City, OH
43123
Phone: 800-282-5113
Option CITY Description
CHASSIS
1000-0002 1 AMBULANCE SPECIFICATIONS
SR00112437 1 Previous unit is #19161
SR00112433
1
Supply a 2022 International MV chassis per quote #17172-06. Chassis includes Liquid Spring.
CHASSIS ORDER SPECIAL COLOR. MED DUTY NAV 2684
1000-0093
1
The chassis is to be ordered special color from chassis OEM.
CHASSIS ORDERED WITH ALUM WHEELS, MD
1000-0085
1
The chassis will include aluminum OEM wheels.
WALK THROUGH FOR NAVISTAR
1000-0066
1
Type 1 Navistar chassis to be modified to provide walk through access to the patient area.
NAVISTAR HUB/LUG COVERS,10 LUG
1000-0468
1
Install chrome finish hub and lug nut covers for International 10 lug wheels.
1000-0476
1
VALVE EXTENSIONS, ALUM WHEELS, INT
Install stainless steel braided filler extensions on the rear tires. Fasten to the center wheel hub
with stainless steel brackets.
TIRE SIZE, 19.5", MEDIUM DUTY:
1000-0073
1
This chassis is specified to have 19.5" tires.
1000-0075
1
CHASSIS IS EQUIPPED WITH AIR BRAKES
This vehicle is specified to have air brakes. Note that proper tire clearances are allowed.
1000-0080
1
CHASSIS IS EQUIPPED WITH HORIZONTAL EXHAUST
The chassis specified above is to include a horizontal exhaust.
1000-0083
1
STANDARD CAB HEIGHT
The specified chassis will have the standard cab height.
1000-0258
1
MUD FLAPS FRONT, INTERNATIONAL
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 2
Option
QTY
Description
Install mud flaps behind each front tire.
MUD FLAPS, REAR, LARGE W/LOGO
1000-0346
1
Install individual rear mud flaps behind each set of rear wheels. Mud flaps to include Horton
logo.
REAR DOCK BUMPERS
1000-0087
1
Install two (2) black rubber standard sized dock bumpers. Locate one on either side of the rear
step on the end caps.
1000-0090
1
REINFORCE REAR BUMPER END CAPS
Reinforce end caps of rear bumper for greater impact resistance.
1000-0145
1
STEP/TANK TRIM SINGLE CAB INT. STD HEIGHT
Install diamond plate step well covers on both the curb and street side cab step wells. The
covers shall sized appropriately for a standard cab.
REAR TOW HOOKS
1000-0105
1
Install (2) tow hooks rear of vehicle. Attach to bumper frame.
1000-0229
1
REAR STEP/ BUMPER ASSEMBLY, INTERNATIONAL
Install a diamondplate rear step/bumper assembly with flip -up center section.
SR00112434
1 The chassis is coming equipped with a Liquid Spring suspension.
SR00112270
1 Install a drive shaft loop just behind the U joint. J
BODY
SR00111996
1
AMBULANCE BODY CONVERSION MODEL IS TO BE A 603A USING A INTERNATIONAL 4300
CHASSIS. MODIFY TO BE 170%.
HEADROOM, 74"
2000-0014
1
The headroom is to be 74".
2000-0625 1
2000-0245 1
2000-0247 1 1
ALUM. DIAMONDPLATE AT SIDE STEPWELL
Fabricate the stepping surface inside the side access door using polished aluminum diamond
treadplate.
DOUBLE STEP CURBSIDE ENTRY, 6" DROP SKIRT
Fabricate curbside of body with 6" drop skirt. To include two step side entry.
NO BODY DROP, STREETSIDE
The streetside bodv forward of the rear wheels will not have a drop skirt.
2000-0250
1
SOUND PROOFING/ACOUSTIC ENHANCEMENT PACKAGE
Install standard sound control package.
2000-0259
1
PRIVACY WINDOWS, FIXED, REAR ENTRY DOORS
Install privacy tinted solid fixed windows in the rear module access doors.
2000-0263
1 PRIVACY WINDOW, SLIDING FOR SIDE ENTRY DOOR
Install a sliding tinted privacy window in the side access door.
2000-1054
1 PRIVACY WINDOW, ABOVE SQUAD BENCH, WITH BELTS
A fixed privacy window shall be installed on the curbside of the body above the squad bench. Use
shortened window to clear 4pt seatbelts.
Spec Writer:
Spec Designer:
Quote # Q000000005904
November 9, 2020
Page 3
Option
CITY
Description
EMERGENCY RELEASE, REAR DOORS
2000-0265
2
Install standard emergency release knobs on top and bottom of the rear module entrance
doors. _
EMERGENCY RELEASE, SIDE ACCESS DOOR
2000-0704
1
Install emergency release knobs on top and bottom of the side module entrance door.
1
DOOR HANDLES
2000-0010
Install Tri-Mark free floating style door handles with pre -stretched stainless steel cables. Include three
piece interior door panels on all access doors.
2000-0813
1
VI -TECH MOUNTING, INTERNATIONAL
Install standard Vi-Tech body mounts.
STAINLESS STEEL SPLASH SHIELDS
2000-0269
1
Install brushed stainless splash shields on the lower front face of the body just behind the cab access
doors. These splash shields are to be the same height as the diamond plate front corner guards.__
FENDERS, RUBBER
2000-0509
1
Install rubber extruded fenders around the rear wheel well openings.
C CHANNEL RUB RAILS
2000-0586
1
Install 'C' channel style lower body rub rails.
STANDARD CORNER GUARDS
2000-0652
1
Install standard height polished diamondplate corner guards.
REAR DOOR HOLD OPENS, GRABBER
2000-0281
1
Install chrome Cast Products "Grabber" style rear door hold opens. (NOTE: HOLDOPENS MUST BE
RELOCATED IF TELESCOPIC LIGHTS ARE ORDERED)
REAR RISER ADP
2000-0584.
1
The rear riser is to be fabricated out of polished aluminum diamondplate.
REAR RISER, BACKLIGHTED
2000-0589
1
The specified rear riser is to be laser cut with the logo as provided. The cutout area is to be
backlighted with red LED lighting.
LICENSE PLATE BRACKET, STREETSIDE RISER
2000-1101
1
Install a surface mount rear license plate bracket on the streetside of the rear riser. Include an
LED license plate light.
DOOR REFLECTORS
2000-0598
20
All patient compartment entry doors to include standard red reflectors.
COMPARTMENTATION
SR00112024
1
DELETE EXTERIOR ALS DOOR PER DRAWINGS
2900-1571 1 STREETSIDE FORWARD COMPARTMENT
The height of the streetside front compartment is to be the full available height of the body.
See drawings for compartment dimensions. Compartment is to include standard LED strip
lighting and a single hinged door.
2000-0400 1 SS FORWARD COMPT. DIAMONDPLATE
The streetside forward compartment is to be fabricated from diamondplate.
SR00112018 1 STREETSIDE FORWARD MODIFICATION: Increase width by 10". See drawings.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 4
Option
QTy _
Description
2900-0004
1
ADJUSTABLE SHELF STREETSIDE FRONT ABOVE 02 TANK LOCATION PER DRAWINGS
Install diamond plate adjustable shelving in the streetside forward compartment. Locate as
noted.
2000-0225
SWEEP OUT COMPARTMENT FLOOR, SS FRONT
1
Streetside forward compartment floor is to be sweep -out style.
2900-0095
1
SILL PLATES, STREETSIDE FRONT
Install a stainless sill plate on the streetside forward compartment.
2900-1575
1
STREETSIDE INTERMEDIATE COMPARTMENT
The height of the streetside intermediate compartment is to be reduced to allow space for an
interior cabinet located below the interior countertop. See drawings for compartment
dimensions. Compartment is to include standard LED strip lighting and double hinged doors.
_
2000-0402
1
SS INTRMDT COMPT. DIAMONDPLATE
The streetside intermediate compartment is to be fabricated from diamondplate.
2900-0144
1 ADJUSTABLE SHELF STREETSIDE INTERMEDIATE CENTER PER DRAWINGS
Install diamond plate adjustable shelving in the streetside intermediate compartment. Locate
as noted.
1 CEILING MOUNTED ELECTRICAL EQUIPMENT
2000-0587
Add -on electrical equipment is to be installed on the ceiling of the streetside intermediate
compartment.
1 EXPANDED METAL CAGE, STREETSIDE INTERMEDIATE
2900-0252
Install an expanded metal cage around the onboard electrical equipment per location noted
above. Include access ports to equipment with grip lock around the edges of the openings.
1 SWEEP OUT COMPARTMENT FLOOR SS INTERMEDIATE COMPT
2000-0624
Streetside intermediate compartment floor is to be sweep -out style.
1 SILL PLATES, STREETSIDE INTERMEDIATE
2900-4005
Install a stainless sill plate on the streetside intermediate compartment.
1 SS WHEELWELL COMPARTMENT, DELETE
8000-0145
Vehicle is not equipped with a streetside wheelwell compartment.
1 STREETSIDE REAR COMPARTMENT
SR00112015
The dimensions of the streetside rear compartment are to be as shown in the drawings.
Compartment is to include standard LED strip lighting and double hinged doors.
2900-1579
1 STREETSIDE REAR COMPARTMENT
The height of the streetside rear compartment is to be 3/4 of the available height of the body.
See drawings for compartment dimensions. Compartment is to include standard LED strip
lighting and double hinged doors. _
1 SS REAR COMPT. DIAMONDPLATE
2000-0404
The streetside rear compartment is to be fabricated from diamondplate.
2900-0145
2
ADJUSTABLE SHELF STREETSIDE REAR PER DRAWINGS
Install diamond plate adjustable shelving in the streetside rear compartment. Locate as noted.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 5
Option
CITY
~Description
TOOL MOUNTING PLATE; STREETSIDE REAR
2900-0216
1
Install a .25" thick aluminum plate on the back wall of the streetside rear compartment. Plate
is to have a D/A finish. Install (2) aluminum 'C' channels to the wall and secure the plate using
the 'C' channels.
SWEEP OUT COMPARTMENT FLOOR SS REAR COMPT
2000-0608
1
Streetside rear compartment floor is to be sweep -out style.
SILL PLATES, STREETSIDE REAR
2900-4007
1
Install a stainless sill plate on the streetside rear compartment.
2900-1583
1
CURBSIDE REAR COMPARTMENT
The height of the curbside rear compartment is to be the full available height of the body. See
drawings for compartment dimensions. Compartment is to include standard LED strip lighting
and a single hinged door.
CS REAR COMPT. FLAT ALUMINUM
2000-0409
1
The curbside rear compartment is to be fabricated from flat aluminum.
SR00112017
1
STAIR CHAIR HOLDER: Install a pull-out stair chair tray in the curbside rear compartment.
ADJUSTABLE SHELF CURBSIDE REAR Locate on the right side of the divider above the stair
2900-0148
1
chair
Install diamond plate adjustable shelving in the curbside rear compartment. Locate as noted.
1
2900-4070
FIXED VERTICAL DIVIDER, CURBSIDE REAR 13.5" FROM RIGHT WALL
Install a 16" deep fixed vertical divider in the curbside rear compartment. Locate as noted
a bove.
ROK BACKBOARD STRAP CURBSIDE REAR Position for backboard
2900-0266
1
Install a Rok buckle style backboard strap in the designated compartment.
2000-0611
1
SWEEP OUT COMPARTMENT FLOOR CS REAR COMPT
Curbside rear compartment floor is to be sweep -out style.
2900-4001
1
STAIR CHAIR POCKET, CURBSIDE REAR
A stair chair pocket is to be recessed into the curbside rear compartment inner door panel.
The pocket shall be installed as close to the bottom and hinged side of door as possible. See
drawings for dimensions.
STAIR CHAIR MODEL, STRYKER #6252
2900-2956
1
A Stryker #6252 stair chair will be stored as noted. This is for sizing/placement purposes only.
_
Horton is not to supply this equipment.
2900-4008
1
SILL PLATES, CURBSIDE REAR
Install a stainless sill plate on the curbside rear compartment.
1
CS INTRMDT COMPT, DELETE
8000-0090
Vehicle is not equipped with a curbside intermediate compartment.
1
8000-0143
CURBSIDE FRONT COMPT DOOR DELETE
2900-1204 1 DRI DECK, BLACK
Black Dri-Deck is to be installed on the floor and shelving of all exterior compartments. To
include tapered edge trim pieces where applicable.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 6
Option QTY Description
2900-1206 1 RUBBER WALLS IN BB COMPT, BLACK
The interior of the backboard compartment is to be covered with black rubber matting to
protect equipment stored in this area.
PAINT AND GRAPHICS
SR00112016 1 1
Roof Paint: Module is to be painted white from the inset.
5000-0189 1 MODULE PAINT NAV 2684
The module body is to be painted a special paint color and paint code as noted above.
5000-0031
1 STRIPE: 8" SCOTCHLITE BELTLINE, WHITE
Apply an 8" white Scotchlite beltline stripe.
5000-0014
1
PAINT PANEL: SAMPLE NAV 2684
A painted test panel shall be prepared with the paint color and number noted above,
1
5000-0036
PAINT PANEL: CHASSIS NAV 2684
A painted test panel shall be prepared with the paint color and number noted above, This
panel is specific to the chassis repaint selected.
PIN STRIPE: 1/4" BLACK, NON -REFLECTIVE
5000-0022
1
The single color stripe as described above shall include a 1/4"black pinstripe that surrounds
the entire accent stripe.
DIAMONDGRADE CHEVRON, FULL REAR Fluorsecent Yellow Green, Red
5000-0081
1
Install full rear body chevron pattern using Diamondgrade material. Install inboard or vertical
corner posts and below upper drip rail.
Lettering Streetside of Body
SR00112022
1
Lettering shall be installed on the street side of the body. 8" outlined scotchlite white,
streetside body - Times Bold. EKG on streetside. This lettering shall meet the requirements
listed below.
SR00112020
Spec Writer:
Spec Designer:
1
Configure:
(SOUTH BEND)
(FIRE DEPT.)
(AMBULANCE)
REFER TO DRAWINGS
Lettering on Curbside of Body
Lettering shall be installed on the curbside of the body. This lettering shall meet the
requirements listed below.
Configure:
(SOUTH BEND)
(FIRE DEPT.)
(AMBULANCE)
Refer to Drawings
Quote # Q000000005904 November 9, 2020 Page 7
on QTY Description
SR00111986 1 Lettering shall be installed on the front of the vehicle. This lettering shall meet the
requirements listed below.
SR00112009
SR00112021
Configure: 4" White "MEDIC 1" across top edge of windshield in center on 18928
Configure: 4" White "MEDIC 10" across top edge of windshield in center on 18933
1 Lettering on Cab Doors
Lettering shall be installed on the cab doors. This lettering shall meet the requirements
listed below.
1
5000-0069 1 2
5000-0070 1 2
5000-0190 1 3
INTERIOR FEATURES
Spec Writer:
Spec Designer:
Configure: Install customer supplied door shields
"MEDIC 1" across lower edge of door on 18928
"MEDIC 10" across lower edge of door on 18933
On both front fenders install "MEDIC 1" "3777" State Registration Number on 18928
On both front fenders install "MEDIC 10" "3777" State Registration Number on 18933
See drawings
Lettering Rear of Vehicle
Lettering shall be installed on the rear of the vehicle. 6" Oulined, Scotchlite White, Times
Bold. This lettering shall meet the requirements listed below.
Configure: "SOUTH BEND" above door windows
"FIRE DEPT." below door windows
"M-1" on doors below handles on 18928
"M-10" on doors below handles on 18933
"MEDIC 1" "3777"(State Registration Number) left middle body panel on 18928
"MEDIC 10" "3777"(State Registration Number) left middle body panel on 18933
"XXXX" truck number, lower left body panel. TBD!!
"DIAL 911" logo middle right body panel
refer to drawings
STAR OF LIFE, 12" REAR DOORS PER DRAWINGS
Install 12" star of life per quantity and location information above.
STAR OF LIFE, IS" ONE (1) EACH SIDE PER DRAWINGS
Install 18" star of life per quantity and location information above.
ACCESS DOORS RED SCOTCHLITE STRIP
Install 2" x 12" st
of red Scotchlite at the top of each entry door placed horizontally.
Quote # Q000000005904 November 9, 2020 Page 8
Option
QTY Description
1 ACRYLIC COLOR: LIGHT TINT
2000-0288
All acrylic doors to be light tint.
3 STAINLESS STEEL COUNTER TOPS Fore and aft of CPR seat
2000-0293
Fab and install Stainless pan formed countertops in the patient area.
1 PAINTED STANDARD INHALATION AREA WALLS
2000-0592
The main wall action area walls are to be painted to match the remainder of the interior cabinets.
2000-0303
1
INHALATION PANEL, LAMINATE COVERED
The inhalation panel is to be fabricated from composite material and covered with laminate to match
to color selected.
2000-0457
1
LONCOIN FLECKSTONE BLACK ONYX #150TS
The patient area floor is to be covered in Loncoin Fleckstone Black Onyx #150TS.
2000-0324
1 STAINLESS STEEL RISERS
Install stainless steel on the interior risers. If a cabinet riser accent stripe is ordered the stainless steel
will stop at the bottom edge of the stripe.
1 STAINLESS STEEL LOWER DOOR PANELS
2000-0325
Finish lower section of inside patient compartment doors with stainless steel.
1 WILSONART FASHION GRAY #D381, WALLS
2000-0441
The interior walls are to be made of reinforced structural composite board covered with Wilsonart
Fashion Gray #D381 laminate. This does not apply to areas surrounding the inhalation/CPR seat area.
1 FASHION GREY CABINET COLOR
2000-0667
All interior cabinetry is to be painted Fashion Grey.
1 CABINET PAINT TO BE TEXTURED
2000-0710
The specified cabinet paint is to have a textured finish.
1 ASH GRAY VACU-FORM VINYL COLOR
2000-3012
All seat cushions, backrests and vinyl closeouts are to be covered in Ash Grey colored
material.
1 VACUFORMED UPHOLSTERY
2000-3011
All seat cushions including head and back cushions are to be vacuformed style with .5"
overhang. Cushions are to be installed with Velcro around the full perimeter of the cushion.
All closeouts are to be covered with matching material and installed per standard. Head,
backrest and HOPS cushions are to be made and attached per standard. Bucket seats to be
specified separately.
1 SWIVEL MOUNT BASE FOR USSC ATTENDANT SEAT
2000-0328
Install a swivel base for the specified USSC attendant's seat.
1 Locate the attendant's seat 10" from the main wall and 8.5" away from the linen cabinet.
1 USSC CHILD, BLACK 4-POINT, ASH GRAY
SR00112439
2000-1590
Install a vacu-formed Ash Gray USSC high back bucket seat with integral child safety seat and
black Opt seatbelt and safety vest. The seat to be adjustable front to rear and is to be
mounted at the head of the cot.
1 4 POINT SEAT BELT FOOT OF BENCH, BLACK
2000-0681
Install black 4-pt seatbelt with safety vest at the foot position of the squad bench.
1 4 POINT SEAT BELT HEAD OF BENCH, BLACK
2000-0682
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 9
Option
CITY Description
Install black 4-pt seatbelt with safety vest at the head position of the squad bench.
1 4 POINT SEAT BELT, CPR SEAT, BLACK
2000-0683
Install black 4-pt seatbelt with safety vest at CPR seat location.
1 ALUMINUM INTERIOR CABINETS
2000-0605
All interior cabinets are to be fabricated from aluminum.
2000-0575
1
CABINET TRIM RADIUSED
Install smooth radiused trim molding on all applicable interior cabinets.
IV HANGER, CP WITH RUBBER ARM COT HEAD Per drawing
2900-0079
1
Install a Cast Products recessed IV hanger with rubber arm over the cot head area.
2900-0210
1
IV HANGER, CP WITH RUBBER ARM COT CHEST Per Drawing
Install a Cast Products recessed IV hanger with rubber arm over the cot chest area.
2900-0206
1
IV HANGER, CP WITH RUBBER ARM BENCH HEAD Per drawing
Install a Cast Products recessed IV hanger with rubber arm over the bench head area.
IV HANGER, CP WITH RUBBER ARM BENCH CHEST Per Drawing
2900-0207
1
Install a Cast Products recessed IV hanger with rubber arm over the bench chest area.
1
2000-0650
GRAB RAIL: 6FT ANTI-MIC, ANTI SLIP, OVER BENCH See drawing
Install 6 foot anti -slip main grab rail with anti -microbial coating. Locate offset toward the
bench wall in the patient area ceiling.
GRAB RAIL: 8FT ANTI-MIC. ANTI SLIP, CENTER See drawing
2000-0411
1
Install 8 foot anti -slip main grab rail with anti -microbial coating. Locate centered in the patient
area ceiling.
1
2000-0418
VERTICAL GRAB RAIL, 2' ANTI -MICROBIAL BOLSTER
Install a standard style 2' grab rail with anti -microbial coating. Locate on the bench bolster at
the side access door angled upward toward the forward end.
PATIENT DOOR GRAB RAILS: ANTI -MICROBIAL
2000-0419
1
Install standard 'V' shaped grab rails with anti -microbial coating. Locate on the interior door
panels of all three patient entry doors.
2000-0423
1
CEILING MATERIAL, PLATINUM WHITE COMPOSITE
The standard module ceiling material shall be platinum white aluminum composite.
2000-0578
1
FIRE EXTINGUISHERS: 5LB ABC SHIP LOOSE
Supply and ship loose a five lb ABC fire extinguisher.
2000-0579
1
FIRE EXTINGUISHERS: 5LB ABC SHIP LOOSE
Supply and ship loose a second five lb ABC fire extinguisher.
STREETSIDE CABINETRY
SR00111994
1
INSTALL CUSTOMER SUPPLIED MEDVAULT UNDER INHALATION CT PER DRAWINGS
2000-0339
1
LINEN CLOSET WITH HEAT/AC UNIT IN BOTTOM
Install a storage cabinet behind the attendant seat. Cabinet to be sized for installation of the
HVAC system in the bottom.
FIXED SHELF, UPPER LINEN CLOSET
2900-1076
1
Fab and install a fixed aluminum shelf in the upper section of the linen cabinet. Shelf is to be
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 10
Option
CITY
Description
painted to match the cabinet color.
2900-1078
1
FIXED SHELF, LINEN CLOSET, CENTER SECTION
Fab and install a fixed aluminum shelf in the middle section of the linen cabinet. Shelf is to be
_
painted to match the cabinet color. _
1
2900-1083
ADJUSTABLE SHELF LOWER LINEN CLOSET
Fab and install an adjustable aluminum shelf in the lower section of the linen cabinet. Shelf is to be
painted to match the cabinet color.
2900-2029
2
SOLID LAMINATE -COVERED LINEN CLOSET DOOR
Install hinged solid doors on the linen cabinet. Cover in laminate to match the interior.
2900-1070
1
PIANO HINGE FOR LINEN CLOSET TOP DOOR
The upper linen cabinet door(s) is/are to use piano style hinge.
_
2900-1072
1
PIANO HINGE FOR LINEN CLOSET MIDDLE DOOR
The middle linen cabinet door(s) is/are to use piano style hinge.
2900-1056
1
SOUTHCO LOCKING LATCH, LINEN CABINET DOOR TOP,
Install a stainless flush mount Southco locking pull latch on the upper linen cabinet door.
2900-1064
1
SS LATCH FOR LINEN CLOSET DOOR MIDDLE
Install a stainless flush mount Southco non -locking pull latch on the middle linen cabinet door.
2000-0343
1
STREETSIDE WALL WITH CPR SEAT
Street side cabinet wall to include a CPR seat.
2000-0310
1
CPR SEAT, 28" WIDTH
Streetside CPR seat width to be 28".
2900-4087
_
1
ANGLED UPPER CABINET, FORWARD OF CPR SEAT
The upper cabinet forward of the CPR seat is to be angled.
2900-4086
1
ANGLED UPPER CABINET, AFT OF CPR SEAT
The upper cabinet to the rear of the CPR seat is to be angled.
2000-2050
1
CUSTOM CABINET, Cabinet 1 Dimensions: 12.75H x 18.75W x 16 D - Location: BELOW REAR
COUNTER
Main wall cabinet #1 dimensions are to be as noted above. Note that dimensions are I.D.
2000-0396
1
ACRYLIC SLIDING, Cabinet 1
1
Cabinet specified above is to have sliding acrylic doors.
2000-2051
CUSTOM CABINET, Cabinet 2 Dimensions: 36.5W x 17.75"H x 16 D - Location: Upper Rear
Main Wall
Main wall cabinet #2 dimensions are to be as noted above: Note that dimensions are I.D.
ACRYLIC SLIDING, Cabinet 2
2000-0521
1
Cabinet specified above is to have sliding 3/8" acrylic doors.
INTERIOR ADJUSTABLE SHELVING, Cabinet 2
2900-0172
1
Install painted adjustable shelving in cabinet #2.
2900-4103
1
LIFT UP CABINET FRAMES, UPPER INHALATION CABINET
Install a flip -up restocking cabinet frame on cabinet noted above. Includes gas shocks and
horizontal latches.
UPPER INHALATION CABINET 14.75 H x 27.75 W x 16 D
2000-2058
1
Upper inhalation cabinet dimensions are to be as noted above. Note that dimensions are I.D.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 11
Option
QTY
Description
ACRYLIC SLIDING DOORS, UPPER INHALATION CAB.
2900-1102
1
Cabinet specified above is to have sliding 3/8" acrylic doors.
2900-1094
1 INTERIOR SHELVING, UPPER INHALATION CABINET
Install painted adjustable shelving in upper inhalation cabinet.
_
2000-2059
1 LOWER INHALATION CABINET 12.75 H x 7.75 W x 16 D
Cabinet below the inhalation area dimensions are to be as noted above. Note that dimensions
are I.D.
1 ACRYLIC HINGED DOOR, LOWER INHALATION CAB.
2900-1124
Cabinet below the inhalation counter is to have a 3/8" acrylic vertically hinged door.
2900-1118
1
LATCH, SOUTHCO SS, LOWER INHALATION CABINET
Install stainless flush mount Southco pull latches on the selected hinged doors on the cabinet
designated above.
2900-1113 1 PIANO STYLE HINGE, LOWER INHALATION CABINET
The cabinet(s) below the inhalation area counter is/are to use piano style hinge.
2000-0345 1 PULL OUT WRITING TRAY W/STORAGE BELOW SURFACE
Install a pull out writing table below the inhalation counter top. The writing surface is to be
positioned for use at the attendant seat location. Storage shall be provided below a lift up
writing surface.
2000-0347 1 STORAGE BENEATH THE CPR SEAT
Provide a hinged CPR seat cushion with storage located underneath.
2000-0349 1 GAS HOLD OPEN FOR LIFT UP CPR SEAT CUSHION
Provide a gas holdopen on the flip -up CPR seat cushion to keep the cushion in the upright
position when opened.
CURBSIDE CABINETRY
2000-0359 1 SQUAD BENCH WITH NO CUPS OR WELLS
Provide storage under the squad bench lid/cushion(s). The area shall run where possible under the
bench. The storage pan is to be fabricated from aluminum and painted to match the interior.
8000-0056 1 BENCH END RESTRAINT FOR USE WITH HOPS, DELETE
2000-0377
1
CARGO NET -HEAD OF BENCH
Install a cargo net at the head of the bench. Net to be removeable for cleaning purposes.
SR00112443
1
Install a custom cabinet at the head of the bench. Install (2() rearward -facing drawers
approximately 11"W x 5"H x 16.75"D per previous unit. Include Southco pull latches. Install
a Stainless steel countertop. The specified cargo net is to run from the forward end of the
cabinet to the ceiling.
DOUBLE CUSHION SQUAD BENCH
2000-0744
1
The squad bench cushion is to be two piece.
2000-0380
1
BENCH HOLD OPENS: GAS
Install gas spring hold opens on squad bench lid.
2000-0381 1
BENCH HOLD-DOWN: PADDLE LATCHES (PAIR)
Install recessed paddle latches into the squad bench riser to retain the squad bench lids in the closed
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020
Page 12
Option
QTY
Description
position. The latches shall be both passive and positive.
2000-0382
1
BENCH CUSHION EDGE TRIM:
Trim bench cushion edge with protective aluminum trim, to protect horizontal edge of squad bench
cushion from tears.
2000-0383
1
BENCH BACK CUSHION: FULL SIZE
Install full size bench backrest cushion.
S/W ON A TIP OUT DOOR, FORWARD BENCH
2000-0516
1
Install a tip -out under the head of the squad bench facing the aisle. This door will house both
sharps and waste containers. Containers are to be supplied by Horton. Paint cabinet to match
interior.
BENCH CABINET, HINGED DOORS
2900-0065
2
Fabricate and install a bench ceiling cabinet above the squad bench with lift up 3/8" acrylic
doors.
SR00112440
1
Shorten the bench ceiling cabinet and install a straight forward section for radio install.
Provide battery switched radio power/ground inside this section and terminate one coax at
this location.
SOUTHCO LATCH OVERHEAD BENCH CABINET
2900-1130
2
Install stainless flush mount Southco pull latches on the bench ceiling cabinet.
2900-1135 4 SELF CLOSING HINGE FOR OVERHEAD BENCH CABINET
The bench ceiling cabinet door(s) is/are to use self -closing style hinges.
FRONT WALL CABINETRY
2900-0073
1
FRONT WALL CABINET: FLAT ALUM PAINTED
The front wall cabinet shall be arranged per drawing. Additional configuration information may follow.
Cabinet interior is to be painted to match the interior cabinet color.
The front wall cabinet must have a 25" clear door opening with the Acrylic doors open at 90
SR00112026
1
degrees.
2900-1005
1
ACRYLIC HINGED DOORS, Upper front wall
Cabinet specified above is to have two 3/8" acrylic vertically hinged doors.
SOUTHCO FLUSH SS PULL LATCH TOP FRONT WALL DOOR
2900-1022
2
Install stainless flush mount Southco pull latches on the selected hinged doors on the upper front wall
cabinet.
3
2900-1017
SELF CLOSING HINGES TOP FRONT WALL CABINET
The upper front wall cabinet door(s) is/are to use self -closing style hinges.
2900-1038
1 ADJUSTABLE SHELF, UPPER FRONT WALL TOP CABINET
Fab and install an adjustable aluminum shelf in the upper section of the front wall cabinet as noted.
Shelf is to be painted to match the cabinet color.
1 FIXED SHELF FRONT WALL MIDDLE CABINET
2900-1039
Fab and install a fixed aluminum shelf in the center section of the front wall cabinet as noted. Shelf is to
be painted to match the cabinet color.
1 ADJUSTABLE SHELF, LOWER FRONT WALL CABINET
2900-1042
Fab and install an adjustable aluminum shelf in the lower section of the front wall cabinet as noted.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 13
j Option QTY
Description
j
Shelf is to be painted to match the cabinet color.
2900-1012
ACRYLIC HINGED DOORS, Lower front wall
1
Cabinet specified above is to have two 3/8" acrylic vertically hinged doors.
SOUTHCO SS PULL STYLE LATCH LOWER FRONT WALL DOOR
2900-1032
2
Install stainless flush mount Southco pull latches on the selected hinged doors on the lower
front wall cabinet.
2900-1021
SELF CLOSING HINGES LOWER FRONT WALL CABINET
3
The lower front wall cabinet door(s) is/are to use self -closing style hinges.
2000-1402 1
CAB TO MODULE WALKTHROUGH DOOR, POCKETED
Install a recessed hinged front cabin closeout door on the right front compartment wall.
COT MOUNT
2000-0599 1
STRYKER POWER LOAD, CENTERED Cot Type: Stryker Power Pro XT
Supply and install a Stryker Power load system. Locate in the center position. This option does
not include a cot. Note: this option complies with GSA change notice 8.
2000-0426 1 COT SAFETY HOOK, STRYKER
Install a yellow cot safety hook on the floor near the rear doors. The provided hook shall be a
Stryker to match the cot mount.
VISUAL WARNING
3000-1807 1 WIG WAG HEADLIGHTS, INTERNATIONAL
Install wig wag headlight flasher. Provide a dedicated switch in the front control panel.
Deactivate with high beams and in secondary mode.
3000-1028
4 900 SERIES LED, RED/CLEAR LENS FRONT MODULE FACE (2 ON EACH SIDE OF 900 KKK LIGHT)
(R/W/R/W/R/W/R)
Install Whelen 900 series LED lights as noted. Lights to be red with clear lenses. Lights to
include chrome flanges.
8 900 SERIES LED, RED/CLEAR LENS Please locate: 2 - at rear window level, 2 - street side
3300-1028
upper outboard corners, 2 - curb side upper outboard corners, 2 - rear upper outboard
corners
Install Whelen 900 series LED lights as noted. Lights to be red with clear lenses. Lights to
include chrome flanges.
3200-1102
2 900 SERIES LED, WHITE/CLEAR LENS FRONT FACE OF MODULE (2 ON EACH SIDE OF 900 KKK
LIGHT) (R/W/R/W/R/W/R)
Install Whelen 900 series LED lights as noted. Lights to be white with clear lenses. Lights to
include chrome flanges.
3000-5079
1 900 Series LED White/Clear Lens Front Center KKK
Install a Whelen 900 series LED light on the front face of the body per K requirements. Light to
be white with clear lens. Light to include chrome flange.
1 900 Series LED Amber/Clear Lens Rear Center KKK
3000-5094
Install a Whelen 900 series LED light on the rear face of the module body per K requirements.
Light to be amber with clear lens. Light to include chrome flange.
1 FLASH PATTERN, 80 FPM A/B
3000-0144
Program the emergency lighting flash pattern to 80 FPM A/B.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 14
Option
CITY
Description
700 SERIES LED, RED/CLEAR LENS 1 OVER BOTH REAR WHEEL WELLS
3400-1063
2
Install Whelen 700 series LED lights as noted. Lights to be red with clear lenses. Lights to
include chrome flanges.
700 SERIES LED, RED/CLEAR LENS REAR OF MODULE - SIDE BODY MARKER LIGHTS
3500-1063
2
Install Whelen 700 series LED lights as noted. Lights to be red with clear lenses. Lights to
include chrome flanges.
1
_
3000-0787
RED/CLEAR LENS 700 LED GRILLE, TOP
Install (2) Whelen 700 Series red LEDs with clear lenses in the upper chassis grille. To include
bezels where applicable.
3000-1281
1
RED/CLEAR LENS 400 LED INT. LIGHTS
Install (2) Whelen 400 Series red LED lights with clear lenses on the chassis fenders. To include
housings and weather proof plugs.
Install Whelen LED light strips in the C Channel rubrails. Strips are to be red at forward and
SR00112148
1
rearward locations with white in the middle.
AUDIBLE WARNING
2000-0434 1
3000-0171 1
SR00112147 1
3000-0181
3000-1546
AIR HORNS: OEM ON HOOD, WITH CHASSIS
__The chassis is to include OEM airhorns.
FOOT SWITCH, AIR HORN, PASSENGER'S SIDE
Install a passenger's side foot switch for air horn activation.
Install a pull lanyard in the center of the cab headliner for air horn activation in addition to
the specified foot switch.
1 SIREN, FEDERAL PA30OMSC
Install a Federal PA30OMSC siren in the front console.
1 SPEAKERS, CAST PRODUCTS, INTERNATIONAL
Install Cast Products siren speakers, applicable to International chassis, in the front bumper.
NON -EMERGENCY LIGHTING
3000-0207 1 KKK SIDE BODY MARKER LIGHTS, 700 SERIES LED (PAIR)
Install red Whelen 700 series LED turn/marker lights on each rear side of the module body.
Lights provide module body night time side lighting visibility and turning signal indication.
Lights do not flash with warning lights. Includes chrome flanges.
3000-0217 1 LED EXTERIOR COMPARTMENT LIGHTING
Install full height LED strip lighting in all exterior compartments. with the exception of any
wheelwell compartments. Install vertical strips inside both sides of each compartment. The
lights are to be directed toward the back of each compartment.
3000-0221 1 ROLLED ICC MARKER LIGHTS
Install standard rolled marker lights along the upper corner post front and rear. Do not install in cases
where there are already ICC marker lights installed on a specified lightbar.
3000-0235 1 SCENE LIGHTS, 900 SERIES, LED, SS FRONT
Install a Whelen 900 Series L.E.D. side scene light with chrome flange on the upper streetside
forward area of the body.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 15
Option
CITY
Description
SCENE LIGHTS, 900 SERIES, LED, SS CENTER
3000-0729
1
Install a Whelen 900 Series L.E.D. side scene light with chrome flange on the upper streetside
center of the body.
SCENE LIGHTS, 900 SERIES, LED, SS REAR
3000-0736
1
Install a Whelen 900 Series LED side scene light with chrome flange on the upper streetside
rearward portion of the body.
SCENE LIGHTS, 900 SERIES, LED, CURBSIDE FRONT
3000-0743
1
Install a Whelen 900 Series LED side scene light with chrome flange on the upper curbside
forward portion of the body.
SCENE LIGHTS, 900 SERIES, LED, CS CENTER
3000-0750
1
Install a Whelen 900 Series LED side scene light with chrome flange on the upper curbside
center portion of the body.
SCENE LIGHTS, 900 SERIES, LED, CURBSIDE REAR
3000-0757
1
Install a Whelen 900 Series LED side scene light with chrome flange on the upper curbside
rearward portion of the body.
LOAD LIGHTS WHELEN 900 SERIES LED
3000-0242
1
Install two Whelen 900 Series LED load lights with chrome flanges above the rear body entry
doors.
TAIL LIGHTS, 600 L.E.D. LED REVERSE VERT. MOUNTED
3000-0271
1
Install Whelen 600 series LED stop/tail, reverse, and turn signals. Install lights stacked
vertically above the rear riser in the rear body panels to either side of the rear access doors.
All lights to include chrome flanges.
ARROW LIGHTS 600 SERIES LED, FRONT
3000-0266
1
Install (2) Whelen 600 series LED turn signals on the front face of the body below the
outboard flashers and wire into the turn signal circuit. Lights to include chrome flanges.
ELECTRICAL
3000-0018 1
ELECTRIC DOOR LOCKS COMPARTMENT EXTERIOR
Install power activated door locks on all exterior compartment doors. Locks to be activated by a switch
at each patient area access door. Locks may be overridden by a door key.
_
3000-0019
1
ELECTRIC DOOR LOCKS ACCESS DOORS INTERIOR
Install power activated door locks on all patient area access doors. Locks to be activated by a
switch at each patient area door. Locks may be overridden by a manual slide lever or by the
door key.
ELECTRIC DOOR LOCKS WIRED TO OEM SWITCHES
3000-0022
1
The specified power door locks are to be wired to the chassis OEM door lock switches.
SR00112000
1 Install an emergency unlock switch under the rear street side corner post.
1 ELECTRIC DOOR LOCKS CONCEALED UNDER REAR STEP
3000-0452
Install a concealed switch under the rear step to operate the power door lock circuit. Doors shall be
wired to unlock only on this circuit.
1 REAR RADIO SPEAKERS, CEILING, 1 FRONT, 1 REAR
3000-0033
Install two (2) rear AM/FM radio speakers in the patient compartment ceiling, (1) front and
(1) rear. Provide volume control in the rear switch panel.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 16
Option
QTY_
Description
_
3000-0282
_
1
ELECTRICAL SYSTEM
Install the Intelliplex i4G electrical system. System is to include a USB port installed under the dash for
ease of programming.
1
INPOWER BATTERY SWITCH, WITH WAKE BUTTON 5 min.
3000-0305
Install an Inpower electronic battery switch. Switch is to activate battery power through the vehicle
ignition and is to include an automatic shutdown timer to deactivate battery power after the ignition is
turned off. To include a wake button installed on the front console to activate the electrical system
without using the key.
1050CUL W/CHARGER, ON DEMAND
3000-0534
1
A Vanner #20-1050CUL combination inverter/charger shall be installed in the streetside
intermediate compartment. This inverter operates with out a switch and functions "On
Demand". Wire the charger to the shoreline circuit.
3000-2151
1
VANNER CHARGER/STATUS PANEL
Install a Vanner charger/status panel in standard location.
SR00112145
1
Inverter panels to be located in standard locations.
3000-0320
5
110V INTERIOR OUTLET 1 In Inhalation Area And 1 Over Telemetry Counter. 2 IN ALS
CABINET AND 1 IN BENCH AREA PER DRAWINGS.
Install a 110V outlet(s) as noted.
INTERIOR 12VDC OUTLETS: CL TYPE/USB 1 In Inhalation Area And 1 In Upper Front Wall
3000-0549
2
Install a 12VDC cigarette style/USB outlet(s) as noted. Wire battery hot.
SR00112143
1
Install (2)12V prewires. Locate one in the cab behind the driver's seat and one behind the
inhalation panel. The circuit is to be 12V only active when the engine is running and off of
shore power. Do not connect either end to power. Just leave the wiring there for future use.
3000-1457
SHORELINE 1, 20A AUTO EJECT, RED
1
Mount a Kussmaul Auto Eject 20 amp shoreline inlet in the standard location. Unit is to
include a dynamic disconnect. Cover is to be red.
3000-1500
1
PD BOX LOCATION, LEFT HAND SIDE, SS INT. COMPARTMENT
Install the power distribution panel on the left hand side of the streetside intermediate
compartment. Close off this area from the remainder of the compartment.
REPORT LIGHT, LED
3000-0332
1
Install a 12" LED report light on the action wall to light the counter area.
CLOCK, DIGITAL W/SECONDS: OVER REAR DOORS
3000-0340
1
Installa Horton large face digital 12/24 hour clock with seconds display over the rear doors.
STEP WELL LIGHT VISTA LED
3000-0344
1
Install a 10.5" LED Vista light strip in the standard location on the bench side of the step well. Light to
activate with door open.
3000-0350
1
ROM DUROLUMEN LED ABOVE HEAD IN CEILING
A ROM Durolumen light fixture shall be provided and installed as noted above. Fixture is to be
operable from the rear switch panel as well as through other means as noted within this
document.
3000-0581
1
ROM DUROLUMEN LED ABOVE CHEST IN CEILING
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 17
Option
QTY
Description
A ROM Durolumen light fixture shall be provided and installed as noted above. Fixture is to be
operable from the rear switch panel as well as through other means as noted within this
document.
3000-0582
1
ROM DUROLUMEN LED ABOVE KNEE IN CEILING
A ROM Durolumen light fixture shall be provided and installed as noted above. Fixture is to be
operable from the rear switch panel as well as through other means as noted within this
document.
ROM DUROLUMEN LED ABOVE FOOT IN CEILING
3000-0584
1
A ROM Durolumen light fixture shall be provided and installed as noted above. Fixture is to be
operable from the rear switch panel as well as through other means as noted within this
document.
PATIENT CEILING DOME LIGHTS WHELEN LED
3000-0359
8
Install Whelen 8000EHCR LED dome lights in the patient area ceiling. The lights will have a high/low
feature with the switch in the rear control panel.
3 SWITCH PANEL REAR DOOR PANEL
3000-0525
1
Install an i4G 3-switch control panel on the right rear entry door panel.
TIMER, FLUOR/LED, REAR DOOR PANEL
3000-2113
1
Install an electronic momentary touch timer switch in the specified 14g switch panel on the
right rear entry door panel. The switch will enable time limited operation of the specified
fluorescent/LED check-out lights with the battery switch in the 'off' position. Set timer to 15
minutes.
DUMP OVERRIDE, 14G, REAR DOOR PANEL
3000-5042
1
Install the dump override switch in the panel selected for the right rear entry door inner panel.
SR00112146
1
Install an Optronics "Blue Eye 4000" spotlight behind the passenger's seat. light is to be
hard wired.
FLASHLIGHT, STREAMLIGHT SL20 WITH CHARGER
3000-0370
1
Supply and install SL-20 box light(s) with 12V chargers as noted.
STREAMLIGHT SL-20 WITH CHARGER
3000-0603
1
Supply and install a Streamlight SL20 flashlight with 12v charger as noted above. _
ENGINE HOUR METER
3000-0006
1
Install an engine hour meter in the driver's side of the cab radio console.
BACKUP ALARM RESET, MOMENTARY
3000-0007
1
Install a back-up alarm and provide a momentary backup alarm reset button on the front
console.
PROGRAMMING
6000-0001
1
LIGHT PROGRAMMING: SIDE REAR SCENE
The side rear scene lights shall be wired to transmission reverse, plus standard mode of operation.
6000-0002
1
LIGHT PROGRAMMING: RIGHT SIDE SCENE
The right side scene lights shall come "on" when the side patient door is opened.
6000-0003
1
LIGHT PROGRAMMING: LOAD LIGHT
Program the rear load lights to activate with transmission reverse plus the standard mode of
operation.
Spec Writer:
Spec Designer:
Quote # Q000000005904 November 9, 2020 Page 18
Option
CITY
Description
PROGRAMMING: AUDIBLE LOW VOLTAGE ALARM
6000-0006
1
1
Program an audible alarm to activate if the voltage drops below 11.8 volts for 120 seconds.
ON THE REAR DOOR PANEL SWITCH ADD DOOR LOCK BUTTON TO 3RD SWITCH ON PATIENT
SR00111997
DOOR
6000-0007
LIGHT PROGRAMMING: PARK BRAKE
1
Program a warning to display on the front console readout advising to set the Parking Brake
when the module disconnect switch is "ON" and the transmission is placed in "PARK" or
"NEUTRAL". It will also advise to Disengage the Parking Brake should the vehicle be placed
into gear.
LIGHT PROG: BRAKE LIGHT, BRAKE OVERRIDE
6000-0010
1
Program the lower red flashing warning lights to operate as supplemental brake lights. The
brake light feature is to override the warning mode. Once the brake is released then the lights
should return to flashing.
MODULE DISCONNECT, DEFAULT TO "ON"
3000-1269
1
Program the Module Disconnect to'On' with battery activation.
HVAC
3000-3005
1
AUX.CONDENSER, FRAME MOUNT, INT.
There shall be an auxiliary exterior condenser installed between the frame rails under the
body.
12V HVAC, BOTTOM OF LINEN CABINET
3000-4029
1
Install a ProAir Pre -charged 12V heat/AC system with brushless motor in the bottom of the
linen cabinet.
SR00112002
Use "T" Metallic fittings for HVAC splice locations. See file in V-drive 18928 & 18933
1
3000-0427
NFPA COMPLIANT VENTING, CAST
1
Install an NFPA style venting system to include a 400cfm exhaust fan along with a static vent.
Install 9.5" square polished covers on both vents per drawings.
CO DETECTOR:
3000-0431
1
Install a 12V carbon monoxide detector in the patient area per drawings.
RADIO
3000-0432 1 ANTENNA COAX 1 Start: Behind Driver Seat, End: Front Center of Mod Roof
An RG 58U coax shall be installed terminating as noted above.
3000-1174 1
1000-0408 1
SR00112142 1
3000-5025 1
Spec Writer:
Spec Designer:
PULL WIRE 1 Start: Cab Console, End: Inhalation Wall
Install a radio cable pull wire terminating as noted above. Wire is not to be wire tied or
otherwise prevented from moving freely.
FRONT CONSOLE, INTERNATIONAL
Install standard front console for International chassis.
Install storage for (3) glove boxes and a waste container in the cab. Customer to provide
further information.
POWER TERMINAL, SWITCHED, BEHIND DRIVER
Quote # Q000000005904 November 9, 2020 Page 19
Option
CITY
Description
Install two (2)10 gauge 30 amp cables to positive and ground studs for radio power. Wire one
battery switched and the other as a ground. Locate behind the driver's seat.
i SR00112144
1
Install customer -supplied radio cables. Customer to determine termination points. Install
(2) 22 gauge 9 wire cables from the forward portion of the bench ceiling cabinet to the front
console.
OXYGEN
SR00112025
1
INSTALL TWO (2) Ferno 521 Universal mounts on left wall of 02 comartment.
4000-0001
02 MOUNT, VERT TRACK FOR QRM-V
1
Vertical track for mounting of a QRM-V 02 bottle mount shall be welded on the back wall of
the streetside forward compartment in the right hand corner. Bracket will be set up for an'M'
sized bottle.
4000-0018
1
02 BOTTLE, BRACKET QRM-V
Install a Zico QRM-V oxygen bracket for'M' bottle. Locate in the streetside forward
compartment.
OXYGEN ACCESS
4000-0019
1
Provide access to the oxygen cylinder valve through the wall as depicted on the drawings. The
door shall be hinged so that it swings into the oxygen cylinder storage compartment. Door
material is to match other selected cabinet doors. The opening shall be 7" wide x 11" high and
trimmed with anodized aluminum.
4000-0022
2
02 OUTLET, OHIO MEDICAL 2 In Inhalation Panel
Install 02 outlets per instructions above. Outlets to be Ohio Medical style.
4000-0088 1
FLOWMETER: TUBE TYPE
Supply tube style flowmeter.
4000-0025
1
OXYGEN WRENCH
Install oxygen wrench in oxygen compartment. Mount securely to wall. Mount with length of
chain or cable to allow for use without being removed from the compartment.
SR00112004 1 Install a SSCOR VX-2 portable suction and aspiration unit with charging/retention bracket
on the inhalation wall per drawing.
CERTIFICATIONS
7000-0001 1 KKK-A-1822F CERTIFICATION LABEL
The vehicle shall have weight/payload, electrical load and KKK-A-1822F certification stickers installed in
the 02 compartment.
Spec Writer:
Spec Designer:
SOUTH BEND FIRE DEPT.
RECESSED DCORPOCKET
I`WxAD'H x 1PD
SLIDE OUT STAIR CHAIR TI
'ALL COMPARTMENTS TO BE SWEEP -OUT
603A WT EXTERIOR
NAVISTAR CHASSIS
RUBBER FENDERS) if NTMUDFLAPS STAINLESS WHEEL HUB
4ATTERYTRAY BLUGNUTCOVERS
• 0
A : A i
! � I
w Ii rr i�
WIG WAG
(ALTERNATING)
Not
MEDIC X
NOTE: DRAWINGS ARE FOR GRAPHICAL SPECIFICATION DRAWING
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE &MAY VARY
DURING CONSTRUCTION
REVISIONS
-V DESCRIPTION
603A EXTERIOR
DRAWN BV: CMH
CK BUMPERS
MPER
END CAPS
SOUTH BEND FIRE DEPT. 19161 REVISIONS
REV DESCRIPTION
623 EXTERIOR
DRAWN w. CMH
NON S'
LO
SURFACE
BI
DOC
�•V,G REPRESENTATION ONL Yrni�.n�
DIMENSIONS ARE APPROXIMATE & MAY VARY
DURING CONSTRUCTION
603A WT EXTERIOR
NAVISTAR CHASSIS
WIG WAG
(ALTERNATING)
)CK BUMPERS
JMPER
END CAPS
m Iitr-�r ary I�r_wr ar�v --m a.� m
rr
pm N!G\M MI=Ji. N�6�1. MI=JM NIG�N w=-l"
(i
MEDIC X
SPECIFICATION DRAWING
SOUTH BEND FIRE DEPT. 19161 REVISIONS
RE:V DESCRIPTION DATE
823 EXTERIOR 1/21/20
DRAWN BY: CMH
0
DEF FILL
INSIDE
INSIDE
INSIDE
CL
OPEEARG NIN
CLEAR
OPENING
COMP.
WIDTH
HEIGHT
DEPTH
WIDTH
HEIGHT
SS FWD
28.95
83.63
21.36
26.25
82.66
SS INT
41.91
29.00
21.36
38.28
27.87
SS REAR
37.44
63.62
21.36
32.09
62.66
NOTE; DRAWINGS ARE FOR GRAPHICAL
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE & MAY VARY
DURING CONSTRUCTION
603A WT EXTERIOR
NAVISTAR CHASSIS
113
FIRE
C' CHANNEL RUB RAILS
.25" TOOL PLATE
SPECIFICATION DRAWING
SOUTH BEND FIRE DEPT.
603A WT EXTERIOR
NAVISTAR CHASSIS
�� 9 9
SOUTH
I '
-" AMBULANCE
,Ili ll.
FIRE IEDIJ
RECESSED DOOR POCKET
10" IN x 40" H x 1.2" D
SLIDE OUT STAIR CHAIR TRAY
RUBBER FENDERS
INSIDE I INSIDE I INSIDE CLEAR I CLEAR
COMPT WIDTH HEIGHT DEPTH OPENING OPENIN(
WIDTH HEIGHT
:S REAR 29.61 1 83.63 1 21.36 1 25.09 1 82.66
NOTE. DRAWINGS ARE FOR GRAPHICAL
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE & MAY VARY
DURING CONSTRUCTION
DROP
REVISIONS
19161 REV DESCRIPTION
623 EXTERIOR
DRAWN BY: CMH
L7tj,,
ALUMINUM WHEELS WITH
FRONT MUD FLAPS STAINLESS WHEEL HUB
BATTERY TRAY & LUG NUT COVERS
SPECIFICATION DRAWING
SOUTH BEND FIRE DEPT.
74
603A WT FRONT WALL
NAVISTAR CHASSIS
96.250
—20.5
(A/C CHUTE)
--20.00
(LEFT FRONT)
LUST HAVE
25" C.D.O.
31.75W X 67H X 22D
PAINTED INTERIOR
0 0
0 0
0
o
-will
WILL NOT
A/C OUTLET
� O
a
MEET KKK
REQUIREMENT
,
02
ACRYLIC
ACRYLIC
—S/S NO
PULL LA
00
CHILD
SAFETY
o
/
—_
67.1
=
I
..
SEAT
o'
x:
t
------
33.000
ACRYLIC
ACRYLIC
SURFACE MOUNTM-' —
LOCKING
'CHES
00
NOTE: DRAWINGS ARE FOR GRAPHICAL SPECIFICATION DRAWING
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE &MAY VARY
DURING CONSTRUCTION
REVISIONS
DESCRIPTION DATE
603A FRONT WALL 11/9/20
DW —BY: CMH
REVISIONS
SOUTH BEND FIRE DEPT.
603A WT CABINET WALL "B"
NAVISTAR CHASSIS
NOTE: DRAWINGS ARE FOR GRAPHICAL
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE & MAY VARY
DURING CONSTRUCTION
20.0
2.00
19"H
16.00
�10.00--4
18.75W X 12.75H X 16D (ID)
12.00
2. 0
16"H
16.00
—� �--2.00
REINFORCE FOR
MONITOR BRACKET
.75' SCAB
A/C CHUTE
69H X 20.5W X 3.51)
LEFT FRONT CABINET
24W X 69H X 20D
—9W X 14H X 18D (OD)
7.75W X 12.75H X 16D (ID)
PULL OUT DRAWER
WITH WRITING SURFACE
16.75"W x 6.125'H x 18"D
DRAWER SIZE:
13.5"W x 3"H x 16"D id.
SPECIFICATION DRAWING
) 603 CABINET WALL B
DRAWN 6Y: CMH
HD LOCKING LATCH
LATCH
HEAT/AC INTAKE
SOUTH BEND FIRE DEPT.
603A WT SIDE WALL
NAVISTAR CHASSIS
167.000
-ARGO NET
14WX11HX12D
SOLID SURFACE WITH 1 INCH SCAB
COVED INTERIOR EDGES —81 W X 11 H X 8D
1
0 0 O ..0 _I' F o
RADIO
PANEL / ACRYLIC / / ACRYLIC /
21.00—
_ _l
f
FF___
O
S/S I�---
LL
S/S LOWER I R�aco.. of I = _ _
DOOR PANEL
a L J
III I I r �
J — L — — — — I (2) REAR -FACING DRAWERS L
11 "W x 5"H x 16.75"D (ID)
J
TIP -OUT SHARPS/WASTE
VISTA LED 15.625"W x 14.5"H x 9"D (ID)
6" DROP STEPWELL LIGHT
DOOR LOCK SWITCH
NOTE: DRAWINGS ARE FOR GRAPHICAL
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE & MAY VARY
DURING CONSTRUCTION
S/S RISER
SPECIFICATION DRAWING.
REVISIONS
E4 DESCRIPTION
603A SIDE WALL
DRAWN BY: CMH
SOUTH BEND FIRE DEPT.
603A WT REAR WALL
NAVISTAR CHASSIS
DUMP SWITCH
DOOR LOCK SWITCH
DUROLUMEN TIMER
NOTE: DRAWINGS ARE FOR GRAPHICAL SPECIFICATION DRAWING
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE &MAY VARY
DURING CONSTRUCTION
REVISIONS
DESCRIPTION
B03 REAR WALL
DHAYM- CMH
FRONT
SOUTH BEND FIRE DEPT.
603A WT OVERHEAD "B" WITH CPR SEAT
NAVISTAR CHASSIS
INTERIOR COVER ONLY
REINFORCE CEILING -INTERIOR COVER ONLY
FOR CARGO NET
Ell
A
Ml
III
m
Elml.0
m
MINIM
PANEL
SEAT
NOTE: DRAWINGS ARE FOR APPROXIMATE
&MAY AL
VA SPECIFICATION DRAWING
REPRESENTATION ONLY
DIMENSIONS ARE APPROXIMATE R MAY VARY
DURING CONSTRUCTION
REVISIONS
=V DESCRIPTION
603A OVERHEAD
DRAWN 9V: CMH
SPEAKER
SOUTH BEND FIRE DEPT.
WAKE-UP
BUTTO
31.00
12..00
22.50
i
18.00
TOP VIEW
NAVISTAR MV CONSOLE & EXTENSION
BLACK LINE-X COATED
CARBON FIBER TOP PLATES
I.
•
RUMBLER
PA30OMSC SIREN
ADJUSTABLE
DIVIDERS
14
SIDE VIEW
SPECIFICATION DRAWING
REVISIONS
=V DESCRIPTION
CONSOLE DRAWING
DRAWN BY: GMH
DASH
52
Horton
EMERGENCY VEHICLES
/Z1."GROUP
Exceptions/Clarifications to specifications:
1.4 WARRANTY:
The warranties offered are attached to our proposal.
1.6 DELIVERY:
Anticipated delivery is stated on our proposal page per Addendum #1.
2.0 CHASSIS MODEL AND TYPE:
Our detailed chassis proposal is included and exceeds what is requested.
2.1 OEM AIR RIDE SYSTEM:
Our proposal includes a Liquid Spring suspension per Addendum #1.
3.2 WIRING MODULE:
Our proposal includes a small electrical cabinet in the top of the cabinet behind the attendant's seat.
Our system does not require all of the space allowed for in the specification.
3.6 DRIVER SWITCHING CONSOLE:
We are offering touch screen controls for our standard multiplexed electrical system. All data and
control features otherwise specified are included.
5.0.1 SUBSECTION OF 5.0 EXTERIOR LIGHTING:
We are offering DOT lighting to match the current fleet.
6.3 ROOF, 6.4 SIDES, 6.5 FLOOR & 6.7 COMPARTMENT AND ENTRY DOOR CONSTRUCTION:
Horton
EMERGENCY VEHICLES
/Z1."GROUP
Our body construction designs, methods and materials vary from those specified and will match the
existing fleet.
6.27 POCKET WHITEBOARD:
This feature is not compatible with the design of this wall.
7.2 EXTERIOR COMPARTMENT DOOR HANDLES AND LATCHING:
Our door handle and latching systems differ from what is specified and will match the existing fleet.
7.12 COMPARTMENT ILLUMUNATION:
The proposed compartment lights are full length LED strips to match existing fleet.
10.0 CEILING HEADLINER:
Our wiring raceway is located above the main cabinet wall in lieu of the ceiling so as to leave the ceiling
area clear of any obstructions.
11.2 ACTION AREA CONTROL PANEL:
We are offering touch screen controls for our standard multiplexed electrical system. All data and
control features otherwise specified are included.
27.0 EQUIPMENT FURNISHED:
This section has been deleted per Addendum #1.
24.0.1 OXYGEN SYSTEM
We have included a Zico QRM-V 02 tank bracket in lieu of the steel band style specified.
25.2 PAINT BODY COLOR:
We are proposing Sikkens paint in lieu of PPG as specified. This matches the existing fleet.
Horton
EMERGENCY VEHICLES
/Z1."GROUP
Notes:
5.7 RUB RAIL LIGHTS:
Note that this style of rub rail, along with the lighting specified, do not match the existing fleet. We have
provided for it in our proposal. Deleting it and using what was used on the existing fleet would result in
a $948.00 reduction is our price proposal.
8.4 COUNTERTOPS:
In lieu of the specified Stainless Steel countertop work surfaces, the existing fleet is using solid surface
material with coved interior seams. This feature can be added at all three specified locations to match
the existing fleet should it be deemed to be appropriate. The cost to make this change is $1,773.00.
9.0.1 THINLITE LIGHTS:
The existing fleet does not include these lights or the referenced timer. Our proposal includes ROM
Durolumen lights with an electronic timer. Should these features be deleted, then the credit for this
deletion would be $1,209.00.
10.3 INTERIOR PROTECTION:
The existing fleet does not include Stainless Steel risers. The existing fleet does include carbon fiber
inner door panels. Our proposal includes Stainless risers and Formica door panels with Stainless
kickplates. The cost to match the existing fleet will be $1,019.00.
10.4 INTERIOR COLORS AND MATERIALS:
Please note that this section does not match the existing fleet. Our proposal matches the existing. There
is no price difference.
18.0 ALS CABINET:
Please note that the ALS cabinet does not match the existing fleet. For the sake of continuity we are
proposing the configuration on the existing units. If we need to change it to what is specified, then there
is no price difference.
Horton
EMERGENCY VEHICLES
/Z1-1'GR0UP
24.0.2 OXYGEN OUTLETS:
Existing fleet is using Ohio Medical style outlets in lieu of the NCG style specified. We are proposing the
Ohio Medical style. There is no cost difference to switch to NCG.
27.0 MISCELLANEOUS EQUIPMENT
This section was deleted via Addendum #1.
SIREN:
The previous unit included a Rumbler siren. That is not specified currently and is not in our proposal.
This feature can be added for an additional $847.00.
BENCH CABINET:
Our proposal includes a cabinet at the forward end of the squad bench with (2) rearward -facing drawers
to match previous units. Deletion credit to remove is $1,443.00 and would add a third seating position
to the bench.
HOPS SYSTEM:
Please note that this unit is not quoted with our rollover airbag system. That can be added for $645.00.
In order to located tubular and head curtain airbags at the attendant's seat, however, it will require
relocation of the attendant's seat closer to the wall as well as the use of a fixed base.
— Horton
EMERGENCY VEHICLES
ROUP
REFERENCE LIST
9/ 15/ 18
Amherst, MA Fire Department
Chief Tim Nelson - (413) 259-3082
Email: nelsonwC�amherstma.gov
68 N. Pleasant St.
Amherst, MA 01004
Type I Ford F550 4x4 with a Horton 623 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonambulance.com
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonambulance.com
- Horton
EMERGENCY VEHICLES
/ R0UP
Baltimore City Fire Department
Chief Mark Fletcher- (410) 396-5680
Email: Mark. Fletcher(aD-baltimorecity.gov
401 E. Fayette Street
Baltimore, MD 21202
Type I Ford F550 4x4 with a Horton 457 Module
rr - *'. ' . .
- Horton
EMERGENCY VEHICLES
ROUP
City of Columbus Fire Department
Captain William Griffith — (614) 221-3132
Email: wrgriffith2(ab-columbus. gov
3675 Parsons Ave
Columbus, OH 43207
Type I International 4300 with a Horton 623 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonambulance.com
- Horton
EMERGENCY VEHICLES
/ R0UP
DC Fire & EMS Department
Chief John Donnelly — (202) 673-3395
Email: John.donnelly(a)-dc.gov
2000 14 Street, NW, 5th Floor
Washington, DC 20009
Type I International 4300 with a Horton 623 Module
p: 614.539.8181
tF: 800.282.5113
f: 614.539.8165
hortonambulance.com
- Horton
EMERGENCY VEHICLES
ROUP
Escambia County Department of Public Safety
Chief Steve White — (850) 471-6426
Email: spwhite@myescambia.com
6575 North "W" Street
Pensacola, FL 32505
Type I Ford F450 4A a Horton 603 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonan-b ilance.com
- Horton
EMERGENCY VEHICLES
/ R0UP
Fredericksburg (City of) Fire Department
Battalion Chief Charles Sterne — (540) 372-1059
Email: csteme fd.fredericksburgva.gov
601 Caroline Street, Suite 700
Fredericksburg, VA 22401
Type III Chevrolet G4500 with a Horton 553 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonambulance.com
- Horton
EMERGENCY VEHICLES
ROUP
Howard County Fire Department
Captain Pat LePore — (410) 313-1123
6751 Columbia Gateway Dr
Columbia, MD 21046
Type I Dodge 5500 4x4 with a Horton 603 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonambulance.com
Horton
EMERGENCY VEHICLES
rz—::�GRouP
Norwood MA Fire Department
Chief Anthony Greeley — (781) 440-5202
Email: tgreeley@norwoodma.gov
135 Nahatan Street
Norwood, MA 02062
Type I Ford F550 4x4 with a Horton 623 Module
p: 614.539.8181
tF: 800.282.5113
f: 614.539.8165
hortonan-b ilance.com
- Horton
EMERGENCY VEHICLES
ROUP
Rolling Meadows
Deputy Fire Chief Terry Valentino — (847) 397-3352
Email: ValentinoT(@-cityrm.org
2455 Plum Grove Road
Rolling Meadows, IL 60008
Type I Ford F650 with a Horton 623 Module
F
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonarrtx it ance. com
,f
Horton
EMERGENCY VEHICLES
rz—::�GRouP
Salem, NH Fire Department
Chief Paul Parisi — (603) 890-2200
Email: PParisi _ci.salem.nh.us
152 Main Street
Salem, NH 03079
Type I International TerraStar with a Horton 623
Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonan-b ilance.com
Horton
EMERGENCY VEHICLES
ice,::/OROUP
Sandusky County EMS
EMS Chief Jeff Jackson — (419) 332-7313
Email: JacksonJeff@co.sandusky.oh.us
2100 Countryside Dr
Fremont, OH 43420
Type 1 Freightliner with a Horton 623 Module
p: 614.539.8181
tF: 800.282.5113
f: 614.539.8165
hortonan-b ilance.com
Horton
EMERGENCY VEHICLES
rz—::�GRouP
Superstition Fire and Medical District
Fleet Supervisor Vaughn Croshaw — (480) 797-7392
Email: Vaughn.croshaw(c-sfmd.az.gov
565 N Idaho Rd
Apache Junction, AZ 85119
Type 1 Ford F550 with a Horton 623 Module
p: 614.539.8181
tf: 800.282.5113
f: 614.539.8165
hortonan-b ilance.com
l 4of
t "MA
�r�llr,�s'-�•[+��I 1wer � �
f
,I L yam. � �► ,, r yam=._ ' i7�' I +�.� � � • _ r -- _
er
;T
..........
77
P
*54
s-
--
MCI—
EMT
�
I �V
e` t
�lt I
-
yr, '�e�- it` a �. j, . � ; r -:: -w•'•
3800
1 � A
v -
A
Horton p: 800..82282..51
tf: 001
i — - - 113
EMERGENCY VEHICLES f: 800.513.8192
/Z�VGROUP warranty@hortonambulance.com
hortonambulance.com
STRUCTURAL WARRANTY OVERVIEW FOR END USERS
The module body, manufactured by HEV, is warranted thirty (30) years from the warranty start date as
determined by the HEV body build plate mounted in the module body. All exterior doors and hinges are
warranted against structural defects for thirty (30) years. Interior aluminum cabinetry (exclusive of paint
finish, hardware, moldings, and accessories) is warranted against structural defects for thirty (30) years.
Written approval must be given by HEV prior to the repairs beginning on items covered by this warranty.
Unauthorized work will void this warranty.
If the ambulance body is rechassised by HEV or REVGROUP during the original warranty period, the
structural warranty will be revalidated an additional five (5) years from the expiration of the original warranty
period. Bodies rechassised subsequent times will be warranted an additional five (5) years from the date the
body was last rechassised, provided that necessary repairs are authorized by the owner and performed by
HEV or REVGROUP.
Any rechassis or structural repair work performed by anyone other than HEV or REVGROUP will
void this warranty.
These warranties extend only to standard HEV features and published standard HEV options. Special
options and features that are not part of HEV's published options list shall be subject to the original OEM
manufacturer, if any, as HEV may designate in writing for each specific case.
HEV's warranty does not include the chassis or chassis parts. The warranty does not include normal -wear
parts such as tires, batteries, bulbs, or upholstery. Warranty coverage of special options components will be
considered on a case -by -case basis with the terms given in writing. Warranty coverage is based upon
reasonable maintenance, prompt notification of defects. This warranty will not cover defects resulting from
misuse, negligence, accident, or overloading the vehicle beyond its weight rating. All warranty repairs must
be completed by HEV or a HEV-authorized party. This warranty does not cover work that was not performed
by HEV.
HEV's warranty does not cover travel expenses, towing charges, mileage, downtime, or personnel time
associated with warranty repairs. HEV shall have no obligation to provide a replacement vehicle.
HEV shall determine the extent of warranty repairs.
This manufacturer's warranty is provided in place of any and all other representations or express or implied
warranties, including the implied warranty of merchantability. No person is authorized to make any other or
further representation or warranty on behalf of Horton Emergency Vehicles or its Dealers. Your right to
service and replacement of parts on the terms expressly set forth herein are your exclusive remedies and
neither the manufacturer nor any of its Dealers shall be liable for damages, whether ordinary, incidental, or
consequential.
1
-- Horton tf: 00on : 800..82282..511
113
�. EMERGENCY VEHICLES f: 800.513.8192
/Z� R 0 U P warranty@hortonambulance.com
hortonambulance.com
Filing a Warranty Claim
Contact your authorized Horton Dealer in order to submit warranty claims. Please provide the following:
Horton Serial Number
Chassis VIN
Mileage of the vehicle at the time of concern
What is the symptom or circumstance for the concern to occur?
Third Party Repair Centers
Use of third party companies to perform structural warranty work is not authorized and immediately voids
any remaining warranty. Third Party service centers or chassis dealerships do not represent the HEV
product or quality. HEV and its dealers use service -after -the -sale by HEV-trained personnel and are the only
businesses that are covered under HEV's warranty. Structural repairs and/or any rechassis work by anyone
other than HEV or REVGROUP will void this warranty.
Legal Remedies: Any claim or controversy arising out of or relating to this limited warranty, or beach thereof,
shall be settled by arbitration administered by the American Arbitration Association in Milwaukee, Wisconsin
in accordance with the Commercial Arbitration Rules of the American Arbitration Association. The laws of
the State of Wisconsin shall be applied in any arbitration proceedings, without regard to principles of conflict
of law. Each party shall bear its own costs, fees and expenses of arbitration. The arbitrator(s) determination
and the basis for that determination shall be in writing and shall include an explanation of the basis for the
determination. The determination of the arbitrator(s) shall be final and binding and judgment upon such
determination may be entered in any court having jurisdiction. The arbitration proceedings and arbitration
award shall be maintained by the parties as strictly confidential, except as otherwise required by court order
or as is necessary to confirm, vacate, or enforce the award and for disclosure in confidence to the parties'
respective attorneys, tax advisors, or senior management personnel. Furthermore, any action for breach of
warranty must be commenced within three months following the expiration of the warranty period.
REV 08_06_19
-- Horton
1�C EMERGENCY VEHICLES
/Z�VGROUP
PAINT WARRANTY OVERVIEW FOR END USER
The paint finish is warranted seven (7) years from the warranty start date or 84,000 miles prorated as
follows:
0 — 4 years
= 100%
4 — 5 years
= 50%
5 — 6 years
= 35%
6 — 7 years
= 20%
p: 614.539.8181
tf: 800,282.5113
f: 800.513.8192
warranty@hor onambulance.com
hortonambulance.com
The paint warranty extends only to Sikkens paint applied by HEV to the module body. It does not extend to
the chassis OEM paint, chassis parts, or paint applied by the manufacturers of accessory parts. This
warranty does not extend to and will not cover chips, scratches or gloss reduction due to normal use. This
warranty will not cover defects caused by misuse, negligence or accident.
HEV's warranty does not cover travel expenses, towing charges, mileage, downtime, or personnel time
association with warranty repairs. HEV shall have no obligation to provide a replacement vehicle.
HEV shall determine the extent of warranty repairs.
Horton Emergency Vehicles reserves the unrestricted right at any time, and from time to time to make
changes in the design of, and/or improvements on its products without thereby imposing any obligation on
itself to make corresponding changes or improvements in or on its products theretofore manufactured.
This manufacturer's warranty is provided in place of any and all other representations or express or implied
warranties, including the implied warranty of merchantability. No person is authorized to make any other or
further representation or warranty on behalf of Horton Emergency Vehicles or its Dealers. Your right to
service and replacement of parts on the terms expressly set forth herein are your exclusive remedies and
neither the manufacturer nor any of its Dealers shall be liable for damages, whether ordinary, incidental, or
consequential.
Filing a Warranty Claim
Contact your authorized Horton Dealer in order to submit warranty claims. Please provide the following:
Horton Serial Number
Chassis VIN
Mileage of the vehicle at the time of concern
What is the symptom or circumstance for the concern to occur?
Third Party Repair Centers
Use of third party companies to perform warranty work is not authorized. Third Party service centers or
chassis dealerships do not represent the HEV product or quality. HEV and its dealers use service -after -the -
sale by HEV-trained personnel and are the only businesses that are covered under HEV's warranty.
w Horton
. EMERGENCY VEHICLES
/Z—'VGROUP
p: 614.539.8181
tf: 800.282.5113
f: 800.513.8192
warranty@hortonambulance.com
hMonambulance.com
Legal Remedies: Any claim or controversy arising out of or relating to this limited warranty, or beach thereof,
shall be settled by arbitration administered by the American Arbitration Association in Milwaukee, Wisconsin
in accordance with the Commercial Arbitration Rules of the American Arbitration Association. The laws of
the State of Wisconsin shall be applied in any arbitration proceedings, without regard to principles of conflict
of law. Each party shall bear its own costs, fees and expenses of arbitration. The arbitrator(s) determination
and the basis for that determination shall be in writing and shall include an explanation of the basis for the
determination. The determination of the arbitrator(s) shall be final and binding and judgment upon such
determination may be entered in any court having jurisdiction. The arbitration proceedings and arbitration
award shall be maintained by the parties as strictly confidential, except as otherwise required by court order
or as is necessary to confirm, vacate, or enforce the award and for disclosure in confidence to the parties'
respective attorneys, tax advisors, or senior management personnel. Furthermore, any action for breach of
warranty must be commenced within three months following the expiration of the warranty period.
REV 08_06_19
81
Horton p: 800.282.5113
tf: 800.282.5113
EMERGENCY VEHICLES f: 800.513.8192
lL1�GROUP warranty@hortonambulance.com
hortonambulance. corn
NON-STRUCTURAL CONVERSION WARRANTY OVERVIEW FOR END USERS
Horton Emergency Vehicles' (HEV) warranty extends two (2) years from the warranty start date as noted on the HEV final
manufacturer sticker, or 24,000 miles, whichever occurs first.
These warranties extend only to standard HEV features and published standard HEV options. Special options and
features not part of HEV's published option list shall be subject to such warranty, if any, as HEV may designate in writing
to each specific case.
HEV's warranty does not include the chassis, chassis parts or any components or equipment manufactured by others and
installed by HEV, all of which are subject to warranties issued by other parties. The warranty does not include normal -
wear parts such as tires, batteries, bulbs, or upholstery. Warranty coverage of special options components will be
considered on a case -by -case basis with the terms given in writing. Warranty coverage is based upon reasonable
maintenance and prompt notification of defects. This warranty will not cover defects resulting from misuse, negligence,
accident, or overloading the vehicle beyond its weight rating. All warranty repairs must be completed by HEV or a HEV-
authorized party. This warranty does not cover work that was not performed by HEV.
HEV's warranty does not cover travel expenses, towing charges, mileage, downtime, or personnel time associated with
warranty repairs. HEV shall have no obligation to provide a replacement vehicle.
HEV shall determine the extent of warranty repairs.
HEV's warranty covers the vehicle as delivered. Changes to the vehicle could change the structural integrity of the vehicle
or damage equipment. Specific consent must be obtained from HEV for the warranty to remain in effect.
Horton Emergency Vehicles reserves the unrestricted right at any time, and from time to time to make changes in the
design of, and/or improvements on its products without thereby imposing any obligation on itself to make corresponding
changes or improvements in or on its products theretofore manufactured.
This manufacturer's warranty is provided in place of any and all other representations or express or implied warranties,
including the implied warranty of merchantability. No person is authorized to make any other or further representation or
warranty on behalf of Horton Emergency Vehicles or its Dealers. Your right to service and replacement of parts on the
terms expressly set forth herein are your exclusive remedies and neither the manufacturer nor any of its Dealers shall be
liable for damages, whether ordinary, incidental, or consequential.
Contact an authorized Horton dealer or representative to make arrangements for work to be completed locally or at
Horton Emergency Vehicles. Occasionally a dealer may need to obtain authorization from HEV for major repair work.
Without Horton approval, any repairs complete may not be covered. All bills for service under warranty must be submitted
to HEV by an HEV-authorized dealer.
Filing a Warranty Claim
Contact your authorized Horton Dealer in order to submit warranty claims. Please provide the following:
Horton Serial Number
Chassis VIN
Mileage of the vehicle at the time of concern
What is the symptom or circumstance for the concern to occur?
Horton
EMERGENCY VEHICLES
✓GROUP
p:614.539.8181
tf: 800.282.5113
f: 800.513.8192
warranty@hortonambulance.com
hortonambulance.com
Third Party Repair Centers
Use of third party companies to perform warranty work is not authorized. Third Party service centers or chassis
dealerships do not represent the HEV product or quality. HEV and its dealers use service -after -the -sale by HEV-trained
personnel and are the only businesses that are covered under HEV's warranty.
Le,:al Remedies: Any claim or controversy arising out of or relating to this limited warranty, or beach thereof, shall be
settled by arbitration administered by the American Arbitration Association in Milwaukee, Wisconsin in accordance with
the Commercial Arbitration Rules of the American Arbitration Association. The laws of the State of Wisconsin shall be
applied in any arbitration proceedings, without regard to principles of conflict of law. Each party shall bear its own costs,
fees and expenses of arbitration. The arbitrator(s) determination and the basis for that determination shall be in writing
and shall include an explanation of the basis for the determination. The determination of the arbitrator(s) shall be final and
binding and judgment upon such determination may be entered in any court having jurisdiction. The arbitration
proceedings and arbitration award shall be maintained by the parties as strictly confidential, except as otherwise required
by court order or as is necessary to confirm, vacate, or enforce the award and for disclosure in confidence to the parties'
respective attorneys, tax advisors, or senior management personnel. Furthermore, any action for breach of warranty must
be commenced within three months following the expiration of the warranty period.
REV 08_06_19
81
��- Horton :800.282.51 f1
t: 00.82.113
8 EMERGENCY VEHICLES f: 800.513.8192
/Z—✓GROUP warranty@hortonambulance.com
hortonambulance.com
ELECTRICAL SYSTEMS WARRANTY OVERVIEW FOR END USERS
Wiring: The stationary wiring harness is warranted for ten (10) years from the warranty start date including,
broken, chafed or pinched wires, and defective splices. Connections at electrical devices are not included in
this ten (10) year warranty.
Intelliplex: The Intelliplex solid state electrical system is warranted for seven (7) years from the warranty
start date or until the vehicle has been driven 100,000 miles, whichever occurs first, including all circuit
boards, circuit board components, and circuit board connections.
All other components are warranted for a period of two (2) years from the warranty start date or until the
vehicle has been driven 24,000 miles, whichever occurs first.
Intelliplex 14G: The Intelliplex 14G solid state electrical system is warranted for ten (10) years from the
warranty start date or until the vehicle has been driven 100,000 miles, whichever occurs first, including all
circuit boards, circuit board components, and circuit board connections.
The Intelliplex AG control panels are warranted for seven (7) years from the warranty start date or until the
vehicle has been driven 100,000 miles, whichever occurs first.
All other components are warranted for a period of two (2) years from the warranty start date or until the
vehicle has been driven 24,000 miles, whichever occurs first.
These warranties extend only to standard Horton Emergency Vehicles (HEV) features and published
standard HEV options. Special options and features that are not part of HEV's published options list shall be
subject to such warranty, if any, as HEV may designate in writing for each specific case.
HEV's warranty does not include the chassis, chassis parts, or any components or equipment manufactured
by others and not installed by HEV, all of which are the subject of warranties issued by other parties. The
warranty does not include normal -wear parts such as tires, batteries, bulbs, or upholstery. Warranty
coverage of special option components will be considered on a case -by -case basis with the terms given in
writing. Warranty coverage is based upon reasonable maintenance and prompt notification of defects. This
warranty will not cover defects resulting from misuse, negligence, accident, or overloading the vehicle
beyond its weight rating. All warranty repairs must be made by HEV or an HEV-authorized party. This
warranty does not cover work that was not performed by HEV or an HEV-authorized party.
HEV's warranty does not cover travel expenses, towing charges, mileage, downtime, or personnel time
associated with warranty repairs. HEV shall have no obligation to provide a replacement vehicle.
HEV shall determine the extent of warranty repairs.
HEV reserves the unrestricted right to, at any time and from time to time, make changes in the design of
and/or improvements on its products without thereby imposing any obligation on itself to make
corresponding changes or improvements in or on its products theretofore manufactured.
Within sixty (60) days of transfer of HEV vehicle ownership by the original purchaser, HEV's warranty may
be revalidated. Revalidation is contingent upon the original or subsequent owner completing vehicle
inspection by HEV or its authorized dealer and filing a warranty revalidation form available from HEV. Upon
81
Horton p: 800.282.5113
tf: 800.282.5113
EMERGENCY VEHICLES f: 800.513.8192
2'✓GROUP warranty@hoaonambulance.com
ho tonambulance.com
subsequent transfer of ownership, this warrant may be revalidated in the same manner, provided that it has
been revalidated on each preceding transfer. The warranty is valid beginning from the warranty start date
and expires at the conclusion of the original warranty term.
This manufacturer's warranty is provided in place of any and all other representations or expressed or
implied warranties including the implied warrant of merchantability. No person is authorized to make any
other or further representation or warranty on behalf of Horton Emergency Vehicles or any of its dealers.
Your right to service and replacement of parts on the terms expressly set forth herein are your exclusive
remedies and neither the manufacturer nor any of its dealers shall be liable for damages, whether ordinary,
incidental, or consequential.
Filing a Warranty Claim
Contact your authorized Horton Dealer in order to submit warranty claims. Please provide the following:
Horton Serial Number
Chassis VIN
Mileage of the vehicle at the time of concern
What is the symptom or circumstance for the concern to occur?
Third Party Repair Centers
Use of third party companies to perform warranty work is not authorized. Third Party service centers or
chassis dealerships do not represent the HEV product or quality. HEV and its dealers use service -after -the -
sale by HEV-trained personnel and are the only businesses that are covered under HEV's warranty.
Legal Remedies: Any claim or controversy arising out of or relating to this limited warranty, or beach thereof,
shall be settled by arbitration administered by the American Arbitration Association in Milwaukee, Wisconsin
in accordance with the Commercial Arbitration Rules of the American Arbitration Association. The laws of
the State of Wisconsin shall be applied in any arbitration proceedings, without regard to principles of conflict
of law. Each party shall bear its own costs, fees and expenses of arbitration. The arbitrator(s) determination
and the basis for that determination shall be in writing and shall include an explanation of the basis for the
determination. The determination of the arbitrator(s) shall be final and binding and judgment upon such
determination may be entered in any court having jurisdiction. The arbitration proceedings and arbitration
award shall be maintained by the parties as strictly confidential, except as otherwise required by court order
or as is necessary to confirm, vacate, or enforce the award and for disclosure in confidence to the parties'
respective attorneys, tax advisors, or senior management personnel. Furthermore, any action for breach of
warranty must be commenced within three months following the expiration of the warranty period.
REV 08_06_19