|
CONSEAL
<br />CONCRETE SEALANTSIr,Ic
<br />SEAL OF SECURITY. BOND OF TRUST.
<br />ConSeal" C5=102
<br />Butyl Rubber Sealant for All Precast
<br />Concrete Structures - Meets ASTM C990
<br />PRODUCT APPLICATIONS
<br />For concrete joints in: Manholes, Concrete Pipe, Vaults, Box Culverts, Septic Tanks,
<br />and Vertical Panel Structures. Not intended for use in expansion joints or joints that move.
<br />SEALING PROPERTIES
<br />• Provides permanently flexible watertight joints.
<br />• Low to high temperature workability: 30°F to 120'F (-1°C to +49'C)
<br />• Rugged service temperature: -30°F to +200°F (-34°C to +93°C)
<br />• Excellent chemical and mechanical adhesion to clean dry surfaces.
<br />• Greater cohesive and adhesive strengths.
<br />• Sealed joints will not shrink, harden or oxidize upon aging.
<br />• Controlled flow resistance for application ease.
<br />• ConSeal CS-102 meets the hydrostatic performance requirement as
<br />set forth in ASTM C990 section 10.1. (Performance requirement:
<br />10psi for 10 minutes in straight alignment — in plant, quality control
<br />test for joint materials.)
<br />• ConSeal CS-102 meets or exceeds all of the requirements of Federal
<br />Specification SS-S-210 (210-A), and AASHTO M-198 Type B.
<br />• No priming normally necessary. When confronted with difficult
<br />installation conditions, such as wet concrete or temperatures below
<br />40°F (4°C), priming the concrete will improve the bonding action.
<br />Consult Concrete Sealants for the proper primer to meet your application.
<br />BUTYL RUBBER SEALANT
<br />PHYSICAL PROPERTIES & CHEMICAL COMPOSITION
<br />Description
<br />Spec
<br />Required
<br />CS-102
<br />Color
<br />Black
<br />Specific Gravity, 77°F
<br />ASTM D71
<br />1.15-1.50
<br />1.25
<br />(25°C)
<br />Ductility, 77°F (25°C)
<br />ASTM D113
<br />5.0 min.
<br />6
<br />Penetration, cone 77°F
<br />ASTM D217
<br />55-100 dmm
<br />55-60 dmm
<br />(250C), 150 gm, 5 sec.
<br />Flash Point, C.O.C., °F
<br />ASTM D92
<br />350°F min.
<br />375°F
<br />Fire Point, C.O.C., °F
<br />ASTM D92
<br />375°F min.
<br />475°F
<br />Hydrocarbon blend
<br />ASTM D297
<br />50% min.
<br />51%
<br />content, % by weight
<br />Inert material filler, % by
<br />AASHTO
<br />30% min.
<br />35%
<br />weight
<br />T111
<br />Volatile Mater, % by weight
<br />ASTM D6
<br />3% max.
<br />1.2%
<br />IMMERSION TESTING
<br />30-Day Immersion Testing: No visible deterioration when tested in 5% Caustic Potash, 5% Hydrochloric Acid, 5% Sulfuric Acid,
<br />and 5% saturated Hydrogen Sulfide.
<br />One Year Immersion Testing: No visible deterioration when tested in 5% Formaldehyde, 5% Formic Acid,
<br />5% Sulfuric Acid, 5% Hydrochloric Acid, 5% Sodium Hydroxide, 5°% Hydrogen Sulfide, and 5% Potassium Hydroxide.
<br />INSTALLATION GUIDELINES
<br />The following procedures should be followed for optimum sealant performance.
<br />• Clean the upper and lower joint surface with a stiff bristle brush.
<br />• Remove any dirt, debris, flashing, or concrete high points, which could keep the joint from coming together.
<br />• ConSeal recommends the use of surface primers, as primers improve adhesion. When using a primer, allow the primer to dry before placing sealant.
<br />• ConSeal primers are specifically designed for use with ConSeal products. Contact ConSeal for the best primer for the projects specific application.
<br />• DO NOT PLACE ANY JOINTS WITHIN 12" OF A CORNER.
<br />• Join the sealant into one continuous strand by kneading the ends together where they meet- Do not stretch the sealant.
<br />• A minimum compression of 50% is required. Greater than 50% compression is optimal. It may take 15-20 minutes for the sealant to fully
<br />compress depending on the ambient temperature and the weight being applied.
<br />Reference Installation Instructions for "Butyl Sealing Tapes" for more detailed instructions.
<br />LIMITED WARRANTY
<br />This information is presented in good faith, but we cannot anticipate all conditions under which this information and our products, or the products of other
<br />manufactures in combination with our products, may be used. We accept no responsibility for results obtained by the application of this information or the safety and
<br />suitability of our products, either alone or in combination with other products. Users are advised to make their own tests to determine the safety and suitability of each
<br />,,._.,_.e<_ o ,i -.. mbi p...,,e�--_o,e«,.e�s
<br />information for this own particular use. We sell this product without warranty, and buyers and users assume all responsibility and liability for loss or damage arising
<br />from the handling and use of this product, whether used alone or in combination with other products
<br />© 2022 CONCRETE SEALANTS, INC. i
<br />CONCRETE SEALANTS, INC. 19325 STATE ROUTE 201, TIPP CITY, OH 45371, USA I WWW.CONSEAL.COM
<br />+1.800.332.7325 +1.937.845.8776
<br />VERSION: 7-APR-2022 CONCRETE SEALANTS, INC.
<br />ISO 9001:2015 REGISTERED
<br />
|