Laserfiche WebLink
Product Information <br />Firestop Wrap Strip <br />(CP 648-S) <br />Product description <br />A single wrap strip of intumescent, flexible firestop for use with <br />plastic and insulated pipe penetrations <br />Product features <br />a Highly intumescent <br />■ Pre -measured — no cutting required <br />■ Integrated fastening tape <br />Cost effective <br />Quick and easy closure without tools <br />Ideal for very tight installations <br />Areas of application <br />Firestopping combustible pipe penetrations <br />Difficult applications where space is limited <br />Penetrations through concrete over metal deck <br />Suitable for the following plastic pipe materials: <br />PVC, CPVC, ABS, FRPP <br />For use with <br />Concrete, masonry, wood floor and gypsum wall assemblies <br />Wall and floor assemblies rated up to 3 hours <br />Examples <br />Waste water pipes <br />Fresh water pipes <br />Decking penetrations <br />Installation instructions for CP 648-S <br />Notice <br />Before handling, read Material Safety Data Sheet and <br />product label for safe usage and health information. <br />• Instructions below are general guidelines — always <br />refer to the applicable drawing in the UL Fire <br />Resistance Directory or HIM Firestop Systems Guide <br />for complete installation information <br />Installation <br />1. Clean the plastic or insulated pipe penetration. <br />Expansion of the intumescent material during a fire <br />closes the plastic pipe. Very dirty pipes (ie: with <br />remains of mortar) may lead to a delay in the closing <br />action. Soiled plastic or insulated pipes should, <br />therefore, be cleaned in the area where the <br />CP 648-S Firestop Wrap Strip is to be installed. <br />2. Install Wrap Strip. First check the annular space <br />to ensure compatibility with the appropriate UL <br />System. Use the CP 648-S Firestop Wrap Strip <br />corresponding to the diameter of the pipe to be <br />installed. Wrap the CP 648-S strip around the pipe <br />and fasten it tightly using the integrated adhesive <br />strip. <br />Push the CP 648-S Firestop Wrap Strip into the <br />annular space in accordance with the UL listing. <br />Technical Data* I CP 648-S <br />Density <br />Dimension (approximate) <br />(thkns" x width" x length") <br />Color <br />Temperature resistance <br />Intumescent activation <br />x. 1.35 g/Cm` <br />1.5": 3/16" x 1 " x 6-3/4" <br />2": 3/16" x 1" x 8-1/4" <br />3": 3/16" x 1-3/4" x 11-1/2" <br />4": 3/8" x 1-3/4" x 15" <br />6": 1/2" x 1-3/4" x 22-1/4" <br />Black with foil backing <br />-40"F to 212"F (-40"C to 1 <br />Expansion ratio (unrestricted) <br />Tested in accordance with <br />• UL 1479 • ASTM E 814 • ASTM G21 <br />320"F <br />1:40 <br />-At 73-F (23oC) and 50% relative humidity <br />G�,garp�FO FOR SEOID OR CAVITY IN THROUGH -PENETRATION TERIAI_�� <br />Q FIRESTOP SYSTEMS ramn momvo�A <br />APPROVED vian meava1-trmveft-fom. <br />CSEE UL FIRE RESISTANCE DIRECTORY rec*^iaeo-sa•n�a�aa <br />66Y7 Me Wbrlml �prporeli"n. <br />3. Seal against smoke and gas. Seal the remaining gap Storage <br />• Store only in the original packaging in a location <br />with Hilti FS-ONE sealant. <br />temperatures between <br />4. For maintenance reasons, a penetration seal can be protected from moisture at <br />permanently marked with an identification plate and 231F and 86oF (-5oC and 30oC). <br />fastened in a visible position next to the seal. <br />Not for use <br />• In highly corrosive surroundings <br />• Outdoors <br />I <br />t. Clean penetration 2A. Wrap the CP 648S 2B. Push the CP 648-S smoeal penetration ke with FFS-ONE <br />4. (ifrequired)installation plate <br />Wrap Strip around Wrap Strip along the pipe <br />the pipe and fasten It and Into <br />the above. <br />bider space sealant. <br />tightly with the <br />adhesive strip. <br />Hilt! Firestop <br />Saving lives <br />through innovation <br />and education <br />Hilti.Out erform.Outlast. <br />Hilt!, Inc. (U.S.) 1-8o0-87 m800 • www.us.h!Ri.com • en espanol 1-800-879-5000 • Hilt! Firestop Systems Guide <br />