Laserfiche WebLink
Quote # Q000000005904 November 9, 2020 Page 8 <br />Option <br />QTY Description <br />1 ACRYLIC COLOR: LIGHT TINT <br />2000-0288 <br />All acrylic doors to be light tint. <br />3 STAINLESS STEEL COUNTER TOPS Fore and aft of CPR seat <br />2000-0293 <br />Fab and install Stainless pan formed countertops in the patient area. <br />1 PAINTED STANDARD INHALATION AREA WALLS <br />2000-0592 <br />The main wall action area walls are to be painted to match the remainder of the interior cabinets. <br />2000-0303 <br />1 <br />INHALATION PANEL, LAMINATE COVERED <br />The inhalation panel is to be fabricated from composite material and covered with laminate to match <br />to color selected. <br />2000-0457 <br />1 <br />LONCOIN FLECKSTONE BLACK ONYX #150TS <br />The patient area floor is to be covered in Loncoin Fleckstone Black Onyx #150TS. <br />2000-0324 <br />1 STAINLESS STEEL RISERS <br />Install stainless steel on the interior risers. If a cabinet riser accent stripe is ordered the stainless steel <br />will stop at the bottom edge of the stripe. <br />1 STAINLESS STEEL LOWER DOOR PANELS <br />2000-0325 <br />Finish lower section of inside patient compartment doors with stainless steel. <br />1 WILSONART FASHION GRAY #D381, WALLS <br />2000-0441 <br />The interior walls are to be made of reinforced structural composite board covered with Wilsonart <br />Fashion Gray #D381 laminate. This does not apply to areas surrounding the inhalation/CPR seat area. <br />1 FASHION GREY CABINET COLOR <br />2000-0667 <br />All interior cabinetry is to be painted Fashion Grey. <br />1 CABINET PAINT TO BE TEXTURED <br />2000-0710 <br />The specified cabinet paint is to have a textured finish. <br />1 ASH GRAY VACU-FORM VINYL COLOR <br />2000-3012 <br />All seat cushions, backrests and vinyl closeouts are to be covered in Ash Grey colored <br />material. <br />1 VACUFORMED UPHOLSTERY <br />2000-3011 <br />All seat cushions including head and back cushions are to be vacuformed style with .5" <br />overhang. Cushions are to be installed with Velcro around the full perimeter of the cushion. <br />All closeouts are to be covered with matching material and installed per standard. Head, <br />backrest and HOPS cushions are to be made and attached per standard. Bucket seats to be <br />specified separately. <br />1 SWIVEL MOUNT BASE FOR USSC ATTENDANT SEAT <br />2000-0328 <br />Install a swivel base for the specified USSC attendant's seat. <br />1 Locate the attendant's seat 10" from the main wall and 8.5" away from the linen cabinet. <br />1 USSC CHILD, BLACK 4-POINT, ASH GRAY <br />SR00112439 <br />2000-1590 <br />Install a vacu-formed Ash Gray USSC high back bucket seat with integral child safety seat and <br />black Opt seatbelt and safety vest. The seat to be adjustable front to rear and is to be <br />mounted at the head of the cot. <br />1 4 POINT SEAT BELT FOOT OF BENCH, BLACK <br />2000-0681 <br />Install black 4-pt seatbelt with safety vest at the foot position of the squad bench. <br />1 4 POINT SEAT BELT HEAD OF BENCH, BLACK <br />2000-0682 <br />Spec Writer: <br />Spec Designer: <br />