Laserfiche WebLink
07-HW-SX11-- <br />Round Pull Latch: Non -locking - Chrome Finish <br />11-X0-0010-- <br />Stowage rating label - Southco round latch 10 pounds applied each <br />07-ZZ-ZZZZ-- <br />07-WC-SS01-- <br />CPR Side Seat: 24" inch - Single Position - Standard <br />07-WC-BR0l <br />I-- Back Rest: Fixed to Back Wall of CPR Seat w/clips <br />07-WC-TAX1-- <br />Telemetry Area: with armrest pad <br />07-CA-49X0-- <br />1/2" Solid Surface Telemetry Area Tray: X-Series STD <br />07-CA-4T19 <br />I-- Gibraltar (Solid Surface) Material COLOR: Northern Melange 9195ML <br />08-SE-1702-- <br />P4 - 4-Point PER4MAX Restraint System - with replacement indicator W/CPR <br />08-SE-1820 < <br />1— (2) on Squad Bench, (1) CPR Side Seat Per4Max Black Belts <br />Belt retractors must mount below the top of the seat. <br />BELT-F151390 <br />08-SE-SB70-- S/B: (3) Sec patient restraints - 9" Sleeves Face of Bench <br />08-SE-SB76-- S/B: (3) Sec patient restraints - 5" Sleeves By Hinge <br />00-20-0072-- Per4Max Four -Point Seatbelts: Accept and Install Full Feature <br />07-ZZ-ZZZZ-- <br />08-00-OOCX Sub Floor, 3/4" Composite, STD <br />08-00-FL30 Flooring: Lonplate H - #424 Gun Metal (Dark Gray) <br />08-00-FL01 -- Flooring Main Edge: 3" Recessed (112" deep) roll -up <br />08-AS-0001 <-- Rear Threshold, Stainless, 6" Wide x Full Width at rear doors <br />Install safety yellow with diagonal stripes nonskid tape over threshold. <br />08-AS-0006 -- CIS Stepwell Threshold, Polished Diamond Plate <br />08-ZZ-ZZZZ-- <br />08-CS-0001 COT MOUNT HARDWARE: (Full Size Mod) <br />08-CR-09PS < I-- Cot Mount: Stryker, No 6390, Power Load, CUST/DLR SUP -MOD option. <br />Install Customer/Dealer supplied Stryker #6390 Power Load system <br />complete with mechanical fasteners as required and electrical connections with testing. <br />Manuf. supplies only the floor cut out by CNC machine and 12v wiring from main electrical <br />system and installation. <br />>>> Caution, Power load head consumes floor space toward attendant seat. Spacing <br />review between seat and cot is recommended. >> <br />08-CR-09PN-- mass casualty kit not requested <br />08-CR-09SM-- No Bolt On Stryker Antler Required. <br />08-CR-1002 <-- 12v power feed location FRONT for Stryker power load 6390 <br />The 12 volt feed will be drilled and fed through the template FRONT hole for a Stryker <br />power load system. The 12volt power shall be brought through the floor, with Heat shrink <br />connectors installed. <br />08-CS-OOPL < I-- Cot Position No 1: PRIMARY CENTER POSITION, <br />Maintain 12" between Cot and S/B. <br />08-CS-2000 < I-- Primary Cot position under floor reinforcement <br />Install 8 inch wide by 5 long 1/2" aluminum reinforcement at primary cot position. <br />(Primary cot position only - REV Std) <br />**If custom location is desired, must be specified below. <br />08-CS-3009 I-- Cot mount set up for: Stryker Power -Pro 6506 <br />08-CS-19A5 I-- Cot Stop, Block: Stryker Power/Performance load. Install hook with kit <br />08-CS-19U1-- Q Straint System: NONE <br />08-OS-04SX OXYGEN / AIR / VACUUM System: X-Series <br />08-OS-0421-- Oxygen Outlet No 1: Amico Console - Latch Key (Chemtron) NCG Style <br />08-OS-040A I-- LOCATION: Action Area <br />08-OS-0422-- Oxygen Outlet No 2: Amico Console - Latch Key(Chemtron) NCG Style <br />08-OS-040A I-- LOCATION: Action Area <br />08-OS-0423-- Oxygen Outlet No 3: Amico Console - Latch Key(Chemtron) NCG Style <br />08-OS-040E I-- LOCATION: Curbside, in head of cabinet, over head of SIB <br />08-OS-090X S < I-- Port Cyl Rack No 1: Zico QR-D-2 - D or Jumbo D - No Strap Req <br />Through bolt the rack to metal. <br />INSTALLED ON SIDE OF RF AILS NEAR WALK THRU <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />