Laserfiche WebLink
• <br />• <br />• <br />a <br />0 <br />v <br />0 <br />0 <br />0 <br />0 <br />m <br />SECTION 6 - TRAFFIC AND LIGHTING <br />11" I.D. Min. , 6" <br />0.75'- -- <br />— — 1.5" Ty <br />I I <br />I I <br />I <br />I - <br />Non -Rotating j N <br />Landing Lug I <br />#6-250mcm I <br />CLl/AL I <br />I 14.0" <br />_ 17.38" <br />SIDE VIEW <br />(Pull Section Cover Removed) <br />Section Thru Metering Compartment <br />ENCLOSURE CONSTRUCTION NOTES: <br />1. Exterior 12 ga. H.D. galv. steel and interior 14 ga. cold rolled steel electrically welded z <br />reinforced where required. <br />2. Construction will be NEMA 3R, raintight. <br />3. All nuts, bolts and screws will be stainless steel. <br />4. Nuts, bolts & screws will not be visible from outside of enclosure. <br />5. Nameplates will be provided as required. <br />6. Control wiring will be marked at both ends by permanent wire markers. <br />7. A plastic covered wiring diagram will be attached to the inside of the front door. <br />8. Enclosure will be factory wired and conform to required NEMA and UL 508A standards. <br />9. Color to be: Char Brown or as specified by Engineering Department. <br />REF STD SPEC SEC 6-2 <br />APPROVED/REVISED BY THE BOARD OF PUBLIC WORKS <br />EFFECTIVE DATE: Month xx, xxxx <br />I Item I Revision I Approved Date I1144",x3. '?' <br />Kara M. <br />Meter Socket w/ Box <br />Landis & GYR 40007-01 <br />w/ Barriers <br />Handle <br />Handle <br />PANEL SIDE VIEW <br />CITY OF SOUTH BEND <br />��e STANDARDS FOR DESIGN <br />AND CONSTRUCTION <br />SERVICE POINTS - SINGLE METER (CABINET AND FOUNDATION STANDARD <br />DETAILS) 6-1 <br />34.00" (Dual) <br />30.00" (Single) <br />0 2.00" <br />26.00" <br />-- - - - - - - - - — - - <br />I <br />�& <br />i <br />CITY BASE DETAIL NOTES <br />r <br />Conduit Entrance <br />Base Must be 34"w X 30"h X 22"d <br />^ .+ <br />Fy I <br />12" (of 30") Must be Exposed Above Ground <br />18" (of 30") Must be Below Ground <br />-- — <br />I <br />I <br />-- <br />L-- <br />----------- <br />22.95" <br />PANEL BASE PLAN <br />-- — <br />5.27" <br />ENCLOSURE CONSTRUCTION NOTES: <br />1. Exterior 12 ga. H.D. galv. steel and interior 14 ga. cold rolled steel electrically welded z <br />reinforced where required. <br />2. Construction will be NEMA 3R, raintight. <br />3. All nuts, bolts and screws will be stainless steel. <br />4. Nuts, bolts & screws will not be visible from outside of enclosure. <br />5. Nameplates will be provided as required. <br />6. Control wiring will be marked at both ends by permanent wire markers. <br />7. A plastic covered wiring diagram will be attached to the inside of the front door. <br />8. Enclosure will be factory wired and conform to required NEMA and UL 508A standards. <br />9. Color to be: Char Brown or as specified by Engineering Department. <br />REF STD SPEC SEC 6-2 <br />APPROVED/REVISED BY THE BOARD OF PUBLIC WORKS <br />EFFECTIVE DATE: Month xx, xxxx <br />I Item I Revision I Approved Date I1144",x3. '?' <br />Kara M. <br />Meter Socket w/ Box <br />Landis & GYR 40007-01 <br />w/ Barriers <br />Handle <br />Handle <br />PANEL SIDE VIEW <br />CITY OF SOUTH BEND <br />��e STANDARDS FOR DESIGN <br />AND CONSTRUCTION <br />SERVICE POINTS - SINGLE METER (CABINET AND FOUNDATION STANDARD <br />DETAILS) 6-1 <br />