My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Ben and Carrie Modlin vs. Historic Preservation Commission (COA#2019-1007A)
sbend
>
Public
>
Common Council
>
Legislation
>
Upcoming Bills
>
2020
>
03-23-2020
>
Ben and Carrie Modlin vs. Historic Preservation Commission (COA#2019-1007A)
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
3/2/2020 10:43:36 AM
Creation date
3/10/2020 4:12:21 PM
Metadata
Fields
Template:
City Council - City Clerk
City Counci - Date
3/9/2020
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
600
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
Show annotations
View images
View plain text
BOARD AND BATTEN INSTALLATION INSIDE CORNER POSTS <br /> r Inside corner posts are the only finish "trim" piece to <br /> BOARD AND BATTEN R be installed prior to the siding. panels. <br /> • Install any inside corners. Fasten the inside <br /> © Weather Barrier&Flashings Furring corners using weather resistant screws placed <br /> o Furring strips for trim Strips <br /> ° Inside Corner Posts inside the pocket of the corner no more than 16" <br /> OCelect Board&Batten Siding Panels I apart. Unlike the other finished trim, inside <br /> °window. Door. Etc.Trim If more than 10' corners are applied before the siding. <br /> NOTE: Make sure not to draw the pocket in when <br /> „ fastening to the wall. <br /> Fig.1 J The pocket width must remain 3/4". Use a scrap <br /> • After preparing the walls for the siding installation (see piece of siding as a spacer in the pocket. The <br /> Wall preparation pg. 8), install 1X2 furring around all inside of the corner post should not lay against <br /> windows, doors, outside corners, etc. This must be done the siding. <br /> anywhere the ends of the siding terminate with the • As a general rule, you will install panels from the <br /> exception of along the bottom of the course up to 10'. if inside corner outward on both sides. <br /> the panels are longer than 10'a furring strip and trim • If installing between two inside corners, 1) <br /> will be neccessary along the bottom as well. (Fig 1-2) install one inside corner, 2) install the panels <br /> • Make sure to install the proper flashing as required by then, 3) install the other inside corner. This way <br /> specific local building codes (Fig 2) you can secure the last panel going into the <br /> NOTE: If no solid nailable substrate exists, either furring second inside corner. Note that you will only be <br /> strips installed horizontally at 12" spacing or solid nailable able to secure the second inside corner on one <br /> sheathing MUST be applied prior to the installation of the side. Be careful to keep it even and square to the <br /> vertical panels. corner. <br /> / I I <br /> Flashing 1" Gap `� <br /> 1 along <br /> horizontal <br /> r lines <br /> A <br /> Install inside corners prior to siding <br /> 1 <br /> Window Header ` <br /> 1 <br /> I <br /> 1/2" Gap <br /> along vertical���; i ,I <br /> linesN. <br /> I <br /> 1X2 Furring Strip Ip , Fig. 2 ,) ' <br /> ,....1X2 <br /> 1 <br /> 28 29 <br />
The URL can be used to link to this page
Your browser does not support the video tag.