Opening of Bids - Venues, Parks, and Arts 2020 Chemical Supply - Hartell's, LLC.

Home Browse Search

ResoluteTm 65WG MIXING Resolute 65WG must be mixed thoroughly in the spray tank to ensure uniform application. Follow these steps: 1. Fill the spray tank 1/4 full with clean water or fluid fertilizer only. 2. Start agitation and check to ensure it is working properly. 3. Add Resolute 65WG directly into the tank. 4. Add the rest of the carrier to obtain the final spray volume. 5. A spray colorant may be used with Resolute 65WG to mark areas as they are treated. This will improve application accuracy by minimizing swath skips and overlaps. 6. Maintain vigorous agitation in the spray tank before and during the application. This will ensure a well -mixed spray suspension. 7. Do not allow spray suspension to dry in the tank. Thoroughly clean the sprayer after use by flush- ing the system with water containing a detergent. Refer to Pesticide Disposal section of this label for waste disposal. TANK MIXING RESOLUTE 65WG Resolute 65WG may be tank mixed with certain other EPA -registered herbicides to provide a broader spectrum of weed control or to control emerged weeds. Refer to the specific directions for use for tank mix partners, and consult the label(s) of the individual tank mix partner(s) for use rate, applica- tion timing, weeds controlled, and specific precautions and/or restrictions. Tank mixes are permitted only in states where the tank mix partner(s) are registered for the application site and the turf and ornamental species listed. When using Resolute 65WG in a tank mixture with other pesticides, observe the most restrictive label limitations and precautions on the labels of the products used. Before tank mixing with other pesticides not named on this label compatibility must be tested. See the Compatibility Test section. COMPATIBILITY TEST Before mixing Resolute 65WG with other pesticides in the spray tank, test the compatibility by mixing all components (carrier and pesticide products) in a small container in proportionate quantities. For example, a 1-qt. jar would be 1/100 the volume of a 25 gals./A spray rate. At 1 Ib./A the Resolute 65WG rate would be proportional to 4.5 g per quart. Add approximately 1.5 teaspoons to a qt. of water. Calculate amounts for other products based on rate per acre. An approximate volume would be 1.5 teaspoons for each Ib./A of a dry formulation and 0.5 teaspoons for each pt./A of a liquid formulation. (See following table). Amount of Component to Add to One Quart Jar of Spray Carrier (Assuming Carrier Volume of 25 gals./A) Rate Per Component Formulations Acre 1,000 Sq. Ft. Level Teaspoons W Resolute 65WG 1.0 lb. 0.4 oz. 1.5 Dry Tank Mix Partners 1.0 lb. 0.4 oz. 1.5 Liquid Tank Mix Partners 1.0 pt. 0.4 oz. 0.5 If components do not ball -up or form flakes, sludge, gels, oily films or layers, then the mixture is com- patible. Incompatibility will usually occur within 5 minutes after mixing. If the components are not compatible, a compatibility agent must be added to the tank mixture. Rerun the test to determine if the mixture is suitable after addition of the compatibility agent. If components are still not com- patible, do not tank mix. MIXING ORDER FOR TANK MIXTURES Notes: 1) When mixing Resolute 65WG with other components (carrier and partner pesticide prod- ucts), allow products to completely dissolve between steps. This is key when tank mixing with ester formulations. 2) Maintain agitation throughout mixing and application of the mixture. Add the products to the spray tank in the following order: 1. Add products packaged in water-soluble bags first. Agitate the tank mixture. Allow the water- soluble bags to completely dissolve and the product to disperse before adding any other tank mix partner. 2. Then add water -dispersible granules (WDG or WG formulations) and wettable powders (WP formulations). Add wettable powders to the tank as agitation continues. Allow the product to disperse completely before other products are added. 3. Add spray adjuvants and spray markers. Read the adjuvant's label first and use only those adjuvants approved for application to turf and ornamentals. 4. Add flowable liquids (FL) or suspension concentrates (SC). 5. Add emulsifiable concentrates (EC) last.