Laserfiche WebLink
Specifications <br />Model MP4124W <br />Volume............................................................................................... . Up to 12.8 GPM <br />Discharge Pressure......................................................................................... <br />Up to 3000 PSI <br />InletPressure.................................................................................................. <br />Up to 90 PSI <br />Speed___ ................................... ................................................................... <br />Up to 1450 RPM <br />Plunger Diameter.. ..... ... _ ............. ...................................................... <br />2411rm <br />PlungerStroke................................................................................................. <br />2611i n <br />Crankcase Oil Capacity.................................................................................. <br />32 fl.oz. <br />Temperature of Pumped Fluids....................................................................... <br />Up to 160 OF <br />Inlet Ports............................................................................. <br />. <br />.......................... (2) 1" NPT <br />Discharge Ports.............................................................................................. <br />(2) 3/4" NPT <br />Pulley Mounting.............................................................................................. <br />Either side <br />Shaft Rotation.................................................................................... <br />Top of Pulley Towards Fluid End <br />Weight............................................................................................................. <br />72 lbs. <br />Crankshaft Diameter....................................................................................... <br />28nrrn <br />Consult the factory for special requirements that must be met if the pump is <br />to operate beyond one oi- more of the limits specified above. <br />l*. J <br />PULLEY INFORMATION <br />Pulley selection and purnp speed are based on a 1725 PRM motor and "B" section belts. When selecting <br />desired GPM, allow for a ±5% tolerance on pumps output due to variations in pulleys, belts and motors <br />among manufacturers. <br />1. Select GPM required, then select appropriate motor pulley from the same line. <br />2. The desired pressure is acheived by selecting the correct nozzle size that corresponds with the pump GPM. <br />MP4124W PULLEY SELECTION AND HORSEPOWER <br />REQUIREMENTS <br />PUMP <br />PULLEY <br />MOTOR <br />PULLEY <br />RPM <br />GPM <br />1500 PSI <br />2000 PSI <br />2500 PSI <br />3000 PSI <br />9.75" <br />4.75" <br />805 <br />7.2 <br />7.5 <br />10.0 <br />12.5 <br />15.0 <br />9.75" <br />5.25" <br />900 <br />8.0 <br />8.4 <br />112 <br />14.0 <br />16.8 <br />9.75" <br />5.75" <br />990 <br />8.9 <br />9.2 <br />12.3 <br />15.4 <br />18.4 <br />9.75" <br />6.25" <br />1085 <br />9.7 <br />10.1 <br />13.5 <br />16.8 <br />20.2 <br />7.75" <br />5.45" <br />1140 <br />10.1 <br />10.5 <br />14.0 <br />17.5 <br />21.0 <br />7.75" <br />5.95" <br />113051 <br />11.61 <br />12.0 <br />16.1 <br />20.1 <br />24.2* <br />7.75" <br />6.45" <br />114501 <br />12-81 <br />13.1 <br />1 17.5 1 <br />21.8 <br />26.7* <br />*Intermittent duty <br />HORSEPOWER RATINGS: <br />The rating shown are the power requirements for the pump. Gas engine power outputs must be <br />approximately twice the pump power requirements shown above. <br />We recommend a 1.15 service factor be specified when selecting an electric motor as the power <br />source. To compute specific pump horsepower requirements, use the Following formula: <br />11P = (GPM X PSI) / 1440 MP4124 - Spec Sheet.pdf <br />